diff mbox series

[RFC,V4,3/4] dt-bindings: mt8183: Add sensor interface dt-bindings

Message ID 20190915065004.20257-4-louis.kuo@mediatek.com (mailing list archive)
State New, archived
Headers show
Series media: support Mediatek sensor interface driver | expand

Commit Message

Louis Kuo Sept. 15, 2019, 6:50 a.m. UTC
This patch adds the DT binding documentation for the sensor interface
module in Mediatek SoCs.

Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
---
 .../bindings/media/mediatek-seninf.txt        | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/mediatek-seninf.txt

Comments

Yingjoe Chen Sept. 16, 2019, 5:33 a.m. UTC | #1
On Sun, 2019-09-15 at 14:50 +0800, Louis Kuo wrote:
> This patch adds the DT binding documentation for the sensor interface
> module in Mediatek SoCs.
> 
> Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
> ---
>  .../bindings/media/mediatek-seninf.txt        | 30 +++++++++++++++++++
>  1 file changed, 30 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/mediatek-seninf.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/mediatek-seninf.txt b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
> new file mode 100644
> index 000000000000..bf2eb801cb47
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
> @@ -0,0 +1,30 @@
> +* Mediatek seninf MIPI-CSI2 host driver
> +
> +Seninf MIPI-CSI2 host driver is a HW camera interface controller. It support a widely adopted,
> +simple, high-speed protocol primarily intended for point-to-point image and video
> +transmission between cameras and host devices.
> +
> +Required properties:
> +  - compatible: "mediatek,mt8183-seninf"
> +  - reg: Must contain an entry for each entry in reg-names.
> +  - reg-names: Must include the following entries:
> +    "base_reg": seninf registers base
> +    "rx_reg": Rx analog registers base

Everyone here is a reg. Adding _reg prefix for everyone looks redundant.
Same for clock-names.


> +  - interrupts: interrupt number to the cpu.
> +  - clocks : clock name from clock manager
> +  - clock-names: must be CLK_CAM_SENINF and CLK_TOP_MUX_SENINF.
> +    It is the clocks of seninf
> +


Joe.C
Sakari Ailus Sept. 18, 2019, 8:29 a.m. UTC | #2
Hi Louis,

On Sun, Sep 15, 2019 at 02:50:03PM +0800, Louis Kuo wrote:
> This patch adds the DT binding documentation for the sensor interface
> module in Mediatek SoCs.
> 
> Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
> ---
>  .../bindings/media/mediatek-seninf.txt        | 30 +++++++++++++++++++
>  1 file changed, 30 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/mediatek-seninf.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/mediatek-seninf.txt b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
> new file mode 100644
> index 000000000000..bf2eb801cb47
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
> @@ -0,0 +1,30 @@
> +* Mediatek seninf MIPI-CSI2 host driver
> +
> +Seninf MIPI-CSI2 host driver is a HW camera interface controller. It support a widely adopted,
> +simple, high-speed protocol primarily intended for point-to-point image and video
> +transmission between cameras and host devices.

Please wrap so it fits to 80 chars per line.

You'll also need to document the graph nodes needed. Which ports correspond
to which interfaces on the device, for instance?

Please document which endpoint properties are required and whether there
are any optional ones.

> +
> +Required properties:
> +  - compatible: "mediatek,mt8183-seninf"
> +  - reg: Must contain an entry for each entry in reg-names.
> +  - reg-names: Must include the following entries:
> +    "base_reg": seninf registers base
> +    "rx_reg": Rx analog registers base
> +  - interrupts: interrupt number to the cpu.
> +  - clocks : clock name from clock manager
> +  - clock-names: must be CLK_CAM_SENINF and CLK_TOP_MUX_SENINF.
> +    It is the clocks of seninf
> +
> +Example:
> +	seninf: seninf@1a040000 {
> +		compatible = "mediatek,mt8183-seninf";
> +		reg = <0 0x1a040000 0 0x8000>,
> +		      <0 0x11C80000 0 0x6000>;
> +		reg-names = "base_reg", "rx_reg";
> +		interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_LOW>;
> +		power-domains = <&scpsys MT8183_POWER_DOMAIN_CAM>;
> +		clocks = <&camsys CLK_CAM_SENINF>,
> +			 <&topckgen CLK_TOP_MUX_SENINF>;
> +		clock-names = "CLK_CAM_SENINF", "CLK_TOP_MUX_SENINF";
> +	}
> +
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/mediatek-seninf.txt b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
new file mode 100644
index 000000000000..bf2eb801cb47
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mediatek-seninf.txt
@@ -0,0 +1,30 @@ 
+* Mediatek seninf MIPI-CSI2 host driver
+
+Seninf MIPI-CSI2 host driver is a HW camera interface controller. It support a widely adopted,
+simple, high-speed protocol primarily intended for point-to-point image and video
+transmission between cameras and host devices.
+
+Required properties:
+  - compatible: "mediatek,mt8183-seninf"
+  - reg: Must contain an entry for each entry in reg-names.
+  - reg-names: Must include the following entries:
+    "base_reg": seninf registers base
+    "rx_reg": Rx analog registers base
+  - interrupts: interrupt number to the cpu.
+  - clocks : clock name from clock manager
+  - clock-names: must be CLK_CAM_SENINF and CLK_TOP_MUX_SENINF.
+    It is the clocks of seninf
+
+Example:
+	seninf: seninf@1a040000 {
+		compatible = "mediatek,mt8183-seninf";
+		reg = <0 0x1a040000 0 0x8000>,
+		      <0 0x11C80000 0 0x6000>;
+		reg-names = "base_reg", "rx_reg";
+		interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_LOW>;
+		power-domains = <&scpsys MT8183_POWER_DOMAIN_CAM>;
+		clocks = <&camsys CLK_CAM_SENINF>,
+			 <&topckgen CLK_TOP_MUX_SENINF>;
+		clock-names = "CLK_CAM_SENINF", "CLK_TOP_MUX_SENINF";
+	}
+