diff mbox series

[5/7] spi: zynq-qspi: Clarify the select chip function

Message ID 20191108105920.19014-6-miquel.raynal@bootlin.com (mailing list archive)
State New, archived
Headers show
Series spi: zynq-qspi: Clarify and fix the chip selection | expand

Commit Message

Miquel Raynal Nov. 8, 2019, 10:59 a.m. UTC 
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.

Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/spi/spi-zynq-qspi.c | 17 ++++++-----------
 1 file changed, 6 insertions(+), 11 deletions(-)
diff mbox series

Patch

diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c
index 34c24b2ad3cf..1ea9a4c2eceb 100644
--- a/drivers/spi/spi-zynq-qspi.c
+++ b/drivers/spi/spi-zynq-qspi.c
@@ -51,7 +51,6 @@ 
 #define ZYNQ_QSPI_CONFIG_BDRATE_MASK	0x00000038 /* Baud Rate Divisor Mask */
 #define ZYNQ_QSPI_CONFIG_CPHA_MASK	0x00000004 /* Clock Phase Control */
 #define ZYNQ_QSPI_CONFIG_CPOL_MASK	0x00000002 /* Clock Polarity Control */
-#define ZYNQ_QSPI_CONFIG_SSCTRL_MASK	0x00000400 /* Slave Select Mask */
 #define ZYNQ_QSPI_CONFIG_FWIDTH_MASK	0x000000C0 /* FIFO width */
 #define ZYNQ_QSPI_CONFIG_MSTREN_MASK	0x00000001 /* Master Mode */
 
@@ -63,7 +62,7 @@ 
  */
 #define ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX	7 /* Baud rate divisor maximum */
 #define ZYNQ_QSPI_CONFIG_BAUD_DIV_SHIFT	3 /* Baud rate divisor shift */
-#define ZYNQ_QSPI_CONFIG_PCS		10 /* Peripheral Chip Select */
+#define ZYNQ_QSPI_CONFIG_PCS		BIT(10) /* Peripheral Chip Select */
 
 /*
  * QSPI Interrupt Registers bit Masks
@@ -313,16 +312,12 @@  static void zynq_qspi_chipselect(struct spi_device *spi, bool assert)
 	struct zynq_qspi *xqspi = spi_controller_get_devdata(ctlr);
 	u32 config_reg;
 
+	/* Ground the line to assert the CS */
 	config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET);
-	if (assert) {
-		/* Select the slave */
-		config_reg &= ~ZYNQ_QSPI_CONFIG_SSCTRL_MASK;
-		config_reg |= (((~(BIT(spi->chip_select))) <<
-				ZYNQ_QSPI_CONFIG_PCS) &
-				ZYNQ_QSPI_CONFIG_SSCTRL_MASK);
-	} else {
-		config_reg |= ZYNQ_QSPI_CONFIG_SSCTRL_MASK;
-	}
+	if (assert)
+		config_reg &= ~ZYNQ_QSPI_CONFIG_PCS;
+	else
+		config_reg |= ZYNQ_QSPI_CONFIG_PCS;
 
 	zynq_qspi_write(xqspi, ZYNQ_QSPI_CONFIG_OFFSET, config_reg);
 }