deleted file mode 100644
@@ -1,60 +0,0 @@
-STMicroelectronics STM32 Peripheral Reset Clock Controller
-==========================================================
-
-The RCC IP is both a reset and a clock controller.
-
-RCC makes also power management (resume/supend and wakeup interrupt).
-
-Please also refer to reset.txt for common reset controller binding usage.
-
-Please also refer to clock-bindings.txt for common clock controller
-binding usage.
-
-
-Required properties:
-- compatible: "st,stm32mp1-rcc", "syscon"
-- reg: should be register base and length as documented in the datasheet
-- #clock-cells: 1, device nodes should specify the clock in their
- "clocks" property, containing a phandle to the clock device node,
- an index specifying the clock to use.
-- #reset-cells: Shall be 1
-- interrupts: Should contain a general interrupt line and a interrupt line
- to the wake-up of processor (CSTOP).
-
-Example:
- rcc: rcc@50000000 {
- compatible = "st,stm32mp1-rcc", "syscon";
- reg = <0x50000000 0x1000>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>,
- <GIC_SPI 145 IRQ_TYPE_NONE>;
- };
-
-Specifying clocks
-=================
-
-All available clocks are defined as preprocessor macros in
-dt-bindings/clock/stm32mp1-clks.h header and can be used in device
-tree sources.
-
-Specifying softreset control of devices
-=======================================
-
-Device nodes should specify the reset channel required in their "resets"
-property, containing a phandle to the reset device node and an index specifying
-which channel to use.
-The index is the bit number within the RCC registers bank, starting from RCC
-base address.
-It is calculated as: index = register_offset / 4 * 32 + bit_offset.
-Where bit_offset is the bit offset within the register.
-
-For example on STM32MP1, for LTDC reset:
- ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset
- = 0x180 / 4 * 32 + 0 = 3072
-
-The list of valid indices for STM32MP1 is available in:
-include/dt-bindings/reset-controller/stm32mp1-resets.h
-
-This file implements defines like:
-#define LTDC_R 3072
new file mode 100644
@@ -0,0 +1,79 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bindings/clock/st,stm32mp1-rcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Reset Clock Controller Binding
+
+maintainers:
+ - Gabriel Fernandez <gabriel.fernandez@st.com>
+
+description: |
+ The RCC IP is both a reset and a clock controller.
+ RCC makes also power management (resume/supend and wakeup interrupt).
+ Please also refer to reset.txt for common reset controller binding usage.
+
+ This binding uses common clock bindings
+ Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+ Specifying clocks
+ =================
+
+ All available clocks are defined as preprocessor macros in
+ dt-bindings/clock/stm32mp1-clks.h header and can be used in device
+ tree sources.
+
+ Specifying softreset control of devices
+ =======================================
+
+ Device nodes should specify the reset channel required in their "resets"
+ property, containing a phandle to the reset device node and an index specifying
+ which channel to use.
+ The index is the bit number within the RCC registers bank, starting from RCC
+ base address.
+ It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+ Where bit_offset is the bit offset within the register.
+
+ For example on STM32MP1, for LTDC reset:
+ ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset
+ = 0x180 / 4 * 32 + 0 = 3072
+
+ The list of valid indices for STM32MP1 is available in:
+ include/dt-bindings/reset-controller/stm32mp1-resets.h
+
+ This file implements defines like:
+ #define LTDC_R 3072
+
+properties:
+ "#clock-cells":
+ const: 1
+
+ "#reset-cells":
+ const: 1
+
+ compatible:
+ items:
+ - const: st,stm32mp1-rcc
+ - const: syscon
+
+ reg:
+ maxItems: 1
+
+required:
+ - "#clock-cells"
+ - "#reset-cells"
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ rcc: rcc@50000000 {
+ compatible = "st,stm32mp1-rcc", "syscon";
+ reg = <0x50000000 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+...