@@ -32,6 +32,13 @@ hdmi_con_in: endpoint {
};
};
+ ext_osc32k: ext_osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
leds {
compatible = "gpio-leds";
@@ -275,6 +282,10 @@ &r_pio {
vcc-pm-supply = <®_aldo1>;
};
+&rtc {
+ clocks = <&ext_osc32k>;
+};
+
&spdif {
status = "okay";
};
@@ -32,6 +32,13 @@ hdmi_con_in: endpoint {
};
};
+ ext_osc32k: ext_osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
leds {
compatible = "gpio-leds";
@@ -276,6 +283,10 @@ &r_ir {
status = "okay";
};
+&rtc {
+ clocks = <&ext_osc32k>;
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ph_pins>;
@@ -20,6 +20,13 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ ext_osc32k: ext_osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
leds {
compatible = "gpio-leds";
@@ -197,6 +204,10 @@ &r_ir {
status = "okay";
};
+&rtc {
+ clocks = <&ext_osc32k>;
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ph_pins>;
@@ -21,6 +21,13 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ ext_osc32k: ext_osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "ext_osc32k";
+ };
+
hdmi_connector: connector {
compatible = "hdmi-connector";
type = "a";
@@ -279,6 +286,10 @@ &r_pio {
vcc-pm-supply = <®_aldo1>;
};
+&rtc {
+ clocks = <&ext_osc32k>;
+};
+
/*
* The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI
* flash and eMMC at the same time, as one of them would fail probing.
@@ -62,13 +62,6 @@ osc24M: osc24M_clk {
clock-output-names = "osc24M";
};
- ext_osc32k: ext_osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "ext_osc32k";
- };
-
pmu {
compatible = "arm,cortex-a53-pmu",
"arm,armv8-pmuv3";
@@ -855,7 +848,6 @@ rtc: rtc@7000000 {
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
clock-output-names = "osc32k", "osc32k-out", "iosc";
- clocks = <&ext_osc32k>;
#clock-cells = <1>;
};
It turns out that not all H6 boards have external 32kHz oscillator. Currently the only one known such H6 board is Tanix TX6. Move external oscillator node from common H6 dtsi to board specific dts files where present. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> --- .../boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 11 +++++++++++ .../arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 8 -------- 5 files changed, 44 insertions(+), 8 deletions(-)