deleted file mode 100644
@@ -1,44 +0,0 @@
-* Calxeda AHCI SATA Controller
-
-SATA nodes are defined to describe on-chip Serial ATA controllers.
-The Calxeda SATA controller mostly conforms to the AHCI interface
-with some special extensions to add functionality.
-Each SATA controller should have its own node.
-
-Required properties:
-- compatible : compatible list, contains "calxeda,hb-ahci"
-- interrupts : <interrupt mapping for SATA IRQ>
-- reg : <registers mapping>
-
-Optional properties:
-- dma-coherent : Present if dma operations are coherent
-- calxeda,port-phys : phandle-combophy and lane assignment, which maps each
- SATA port to a combophy and a lane within that
- combophy
-- calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off,
- which indicates that the driver supports SGPIO
- indicator lights using the indicated GPIOs
-- calxeda,led-order : a u32 array that map port numbers to offsets within the
- SGPIO bitstream.
-- calxeda,tx-atten : a u32 array that contains TX attenuation override
- codes, one per port. The upper 3 bytes are always
- 0 and thus ignored.
-- calxeda,pre-clocks : a u32 that indicates the number of additional clock
- cycles to transmit before sending an SGPIO pattern
-- calxeda,post-clocks: a u32 that indicates the number of additional clock
- cycles to transmit after sending an SGPIO pattern
-
-Example:
- sata@ffe08000 {
- compatible = "calxeda,hb-ahci";
- reg = <0xffe08000 0x1000>;
- interrupts = <115>;
- dma-coherent;
- calxeda,port-phys = <&combophy5 0 &combophy0 0 &combophy0 1
- &combophy0 2 &combophy0 3>;
- calxeda,sgpio-gpio =<&gpioh 5 1 &gpioh 6 1 &gpioh 7 1>;
- calxeda,led-order = <4 0 1 2 3>;
- calxeda,tx-atten = <0xff 22 0xff 0xff 23>;
- calxeda,pre-clocks = <10>;
- calxeda,post-clocks = <0>;
- };
new file mode 100644
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ata/sata_highbank.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Calxeda AHCI SATA Controller
+
+description: |
+ The Calxeda SATA controller mostly conforms to the AHCI interface
+ with some special extensions to add functionality, to map GPIOs for
+ activity LEDs and for mapping the ComboPHYs.
+
+maintainers:
+ - Andre Przywara <andre.przywara@arm.com>
+
+properties:
+ compatible:
+ const: calxeda,hb-ahci
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ dma-coherent: true
+
+ calxeda,pre-clocks:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Indicates the number of additional clock cycles to transmit before
+ sending an SGPIO pattern.
+
+ calxeda,post-clocks:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Indicates the number of additional clock cycles to transmit after
+ sending an SGPIO pattern.
+
+ calxeda,led-order:
+ description: Maps port numbers to offsets within the SGPIO bitstream.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - minItems: 1
+ maxItems: 8
+
+ calxeda,port-phys:
+ description: |
+ phandle-combophy and lane assignment, which maps each SATA port to a
+ combophy and a lane within that combophy
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/phandle-array
+ - minItems: 1
+ maxItems: 8
+
+ calxeda,tx-atten:
+ description: |
+ Contains TX attenuation override codes, one per port.
+ The upper 24 bits of each entry are always 0 and thus ignored.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ - minItems: 1
+ maxItems: 8
+
+ calxeda,sgpio-gpio:
+ description: |
+ phandle-gpio bank, bit offset, and default on or off, which indicates
+ that the driver supports SGPIO indicator lights using the indicated
+ GPIOs.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ sata@ffe08000 {
+ compatible = "calxeda,hb-ahci";
+ reg = <0xffe08000 0x1000>;
+ interrupts = <115>;
+ dma-coherent;
+ calxeda,port-phys = <&combophy5 0>, <&combophy0 0>, <&combophy0 1>,
+ <&combophy0 2>, <&combophy0 3>;
+ calxeda,sgpio-gpio =<&gpioh 5 1>, <&gpioh 6 1>, <&gpioh 7 1>;
+ calxeda,led-order = <4 0 1 2 3>;
+ calxeda,tx-atten = <0xff 22 0xff 0xff 23>;
+ calxeda,pre-clocks = <10>;
+ calxeda,post-clocks = <0>;
+ };
+
+...
Convert the Calxeda Highbank SATA controller binding to DT schema format using json-schema. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Cc: Jens Axboe <axboe@kernel.dk> --- .../devicetree/bindings/ata/sata_highbank.txt | 44 --------- .../bindings/ata/sata_highbank.yaml | 95 +++++++++++++++++++ 2 files changed, 95 insertions(+), 44 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.txt create mode 100644 Documentation/devicetree/bindings/ata/sata_highbank.yaml