| Message ID | 20200507192157.6831-1-sibis@codeaurora.org (mailing list archive) |
|---|---|
| State | Mainlined |
| Commit | d100ff3843b731c5c0c974bc9210cf092a7ec9b6 |
| Headers | show |
| Series | [v5] iommu/arm-smmu-qcom: Request direct mapping for modem device | expand |
Quoting Sibi Sankar (2020-05-07 12:21:57) > The modem remote processor has two modes of access to the DDR, a direct > mode and through a SMMU which requires direct mapping. The configuration > of the modem SIDs is handled in TrustZone. Is it "The configuration of the modem SIDs is typically handled by code running in the ARM CPU's secure mode, i.e. secure EL1"? And is that even true? I though it was programmed by EL2. > On platforms where TrustZone TrustZone is always there. > is absent this needs to be explicitly done from kernel. Add compatibles > for modem to opt in for direct mapping on such platforms. > > Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Is Sai the author? Or does this need a co-developed-by tag? > Signed-off-by: Sibi Sankar <sibis@codeaurora.org> > --- > > V5 > * Reword commit message and drop unnecessary details I don't see any improvement! Probably because I don't understand _why_ the modem needs a direct mapping. The commit text basically says "we need to do it because it isn't done in secure world sometimes". This is probably wrong what I wrote below, but I'd like to clarify to confirm my understanding. Maybe the commit text should say: The modem remote processor has two access paths to DDR. One path is directly connected to DDR and another path goes through an SMMU. The SMMU path is configured to be a direct mapping because it's used by various peripherals in the modem subsystem. Typically this direct mapping is configured by programming modem SIDs into the SMMU when EL2 responds to a hyp call from the code that loads the modem binary in the secure world. In certain firmware configurations, especially when the kernel is entered at EL2, we don't want secure mode to make hyp calls to program the SMMU because the kernel is in full control of the SMMU. Let's add compatibles here so that we can have the kernel program the SIDs for the modem in these cases.
Hey Stephen, Thanks for taking time to review the patch. On 5/8/20 2:44 AM, Stephen Boyd wrote: > Quoting Sibi Sankar (2020-05-07 12:21:57) >> The modem remote processor has two modes of access to the DDR, a direct >> mode and through a SMMU which requires direct mapping. The configuration >> of the modem SIDs is handled in TrustZone. > > Is it "The configuration of the modem SIDs is typically handled by > code running in the ARM CPU's secure mode, i.e. secure EL1"? And is that > even true? I though it was programmed by EL2. What I meant to say was qcom implementation of TZ or qcom proprietary bootloaders. I should have been more specific and mentioned that the configuration is done at EL2 by QHEE (Qualcomm's Hypervisor Execution Environment) before we enter the kernel. > >> On platforms where TrustZone > > TrustZone is always there. > >> is absent this needs to be explicitly done from kernel. Add compatibles >> for modem to opt in for direct mapping on such platforms. >> >> Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> > > Is Sai the author? Or does this need a co-developed-by tag? I decided to include Sai's S-b just to show I took back ownership of the patch from his patch series. I'll drop it in the next re-spin. > >> Signed-off-by: Sibi Sankar <sibis@codeaurora.org> >> --- >> >> V5 >> * Reword commit message and drop unnecessary details > > I don't see any improvement! Probably because I don't understand _why_ > the modem needs a direct mapping. The commit text basically says "we > need to do it because it isn't done in secure world sometimes". This is > probably wrong what I wrote below, but I'd like to clarify to confirm my > understanding. Maybe the commit text should say: Thanks for taking time to reword the commit message will use the same with a few corrections. > > The modem remote processor has two access paths to DDR. One path is > directly connected to DDR and another path goes through an SMMU. The > SMMU path is configured to be a direct mapping because it's used by > various peripherals in the modem subsystem. I'll use ^^ as is. > Typically this direct > mapping is configured by programming modem SIDs into the SMMU when EL2 > responds to a hyp call from the code that loads the modem binary in the > secure world. Typically this direct mapping is configured statically at EL2 by QHEE (Qualcomm's Hypervisor Execution Environment) before the kernel is entered. > > In certain firmware configurations, especially when the kernel is > entered at EL2, we don't want secure mode to make hyp calls to program > the SMMU because the kernel is in full control of the SMMU. Let's add > compatibles here so that we can have the kernel program the SIDs for the > modem in these cases. In certain firmware configuration, especially when the kernel is already in full control of the SMMU, defer programming the modem SIDs to the kernel. Let's add compatibles here so that we can have the kernel program the SIDs for the modem in these cases. Will/Stephen, Let me know if the above changes are okay? I'll re-spin the patch based on your feedback. >
diff --git a/drivers/iommu/arm-smmu-qcom.c b/drivers/iommu/arm-smmu-qcom.c index 5bedf21587a56..cf01d0215a397 100644 --- a/drivers/iommu/arm-smmu-qcom.c +++ b/drivers/iommu/arm-smmu-qcom.c @@ -17,7 +17,9 @@ static const struct of_device_id qcom_smmu_client_of_match[] = { { .compatible = "qcom,mdp4" }, { .compatible = "qcom,mdss" }, { .compatible = "qcom,sc7180-mdss" }, + { .compatible = "qcom,sc7180-mss-pil" }, { .compatible = "qcom,sdm845-mdss" }, + { .compatible = "qcom,sdm845-mss-pil" }, { } };