deleted file mode 100644
@@ -1,83 +0,0 @@
-Texas Instruments K3 Interrupt Router
-=====================================
-
-The Interrupt Router (INTR) module provides a mechanism to mux M
-interrupt inputs to N interrupt outputs, where all M inputs are selectable
-to be driven per N output. An Interrupt Router can either handle edge triggered
-or level triggered interrupts and that is fixed in hardware.
-
- Interrupt Router
- +----------------------+
- | Inputs Outputs |
- +-------+ | +------+ +-----+ |
- | GPIO |----------->| | irq0 | | 0 | | Host IRQ
- +-------+ | +------+ +-----+ | controller
- | . . | +-------+
- +-------+ | . . |----->| IRQ |
- | INTA |----------->| . . | +-------+
- +-------+ | . +-----+ |
- | +------+ | N | |
- | | irqM | +-----+ |
- | +------+ |
- | |
- +----------------------+
-
-There is one register per output (MUXCNTL_N) that controls the selection.
-Configuration of these MUXCNTL_N registers is done by a system controller
-(like the Device Memory and Security Controller on K3 AM654 SoC). System
-controller will keep track of the used and unused registers within the Router.
-Driver should request the system controller to get the range of GIC IRQs
-assigned to the requesting hosts. It is the drivers responsibility to keep
-track of Host IRQs.
-
-Communication between the host processor running an OS and the system
-controller happens through a protocol called TI System Control Interface
-(TISCI protocol). For more details refer:
-Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
-
-TISCI Interrupt Router Node:
-----------------------------
-Required Properties:
-- compatible: Must be "ti,sci-intr".
-- ti,intr-trigger-type: Should be one of the following:
- 1: If intr supports edge triggered interrupts.
- 4: If intr supports level triggered interrupts.
-- interrupt-controller: Identifies the node as an interrupt controller
-- #interrupt-cells: Specifies the number of cells needed to encode an
- interrupt source. The value should be 1.
- First cell should contain interrupt router input number
- as specified by hardware.
-- ti,sci: Phandle to TI-SCI compatible System controller node.
-- ti,sci-dev-id: TISCI device id of interrupt controller.
-- ti,interrupt-ranges: Set of triplets containing ranges that convert
- the INTR output interrupt numbers to parent's
- interrupt number. Each triplet has following entries:
- - First entry specifies the base for intr output irq
- - Second entry specifies the base for parent irqs
- - Third entry specifies the limit
-
-For more details on TISCI IRQ resource management refer:
-http://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
-
-Example:
---------
-The following example demonstrates both interrupt router node and the consumer
-node(main gpio) on the AM654 SoC:
-
-main_gpio_intr: interrupt-controller0 {
- compatible = "ti,sci-intr";
- ti,intr-trigger-type = <1>;
- interrupt-controller;
- interrupt-parent = <&gic500>;
- #interrupt-cells = <1>;
- ti,sci = <&dmsc>;
- ti,sci-dev-id = <131>;
- ti,interrupt-ranges = <0 360 32>;
-};
-
-main_gpio0: gpio@600000 {
- ...
- interrupt-parent = <&main_gpio_intr>;
- interrupts = <192>, <193>, <194>, <195>, <196>, <197>;
- ...
-};
new file mode 100644
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-intr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 Interrupt Router
+
+maintainers:
+ - Lokesh Vutla <lokeshvutla@ti.com>
+
+allOf:
+ - $ref: /schemas/interrupt-controller.yaml#
+
+description: |
+ The Interrupt Router (INTR) module provides a mechanism to mux M
+ interrupt inputs to N interrupt outputs, where all M inputs are selectable
+ to be driven per N output. An Interrupt Router can either handle edge
+ triggered or level triggered interrupts and that is fixed in hardware.
+
+ Interrupt Router
+ +----------------------+
+ | Inputs Outputs |
+ +-------+ | +------+ +-----+ |
+ | GPIO |----------->| | irq0 | | 0 | | Host IRQ
+ +-------+ | +------+ +-----+ | controller
+ | . . | +-------+
+ +-------+ | . . |----->| IRQ |
+ | INTA |----------->| . . | +-------+
+ +-------+ | . +-----+ |
+ | +------+ | N | |
+ | | irqM | +-----+ |
+ | +------+ |
+ | |
+ +----------------------+
+
+ There is one register per output (MUXCNTL_N) that controls the selection.
+ Configuration of these MUXCNTL_N registers is done by a system controller
+ (like the Device Memory and Security Controller on K3 AM654 SoC). System
+ controller will keep track of the used and unused registers within the Router.
+ Driver should request the system controller to get the range of GIC IRQs
+ assigned to the requesting hosts. It is the drivers responsibility to keep
+ track of Host IRQs.
+
+ Communication between the host processor running an OS and the system
+ controller happens through a protocol called TI System Control Interface
+ (TISCI protocol).
+
+properties:
+ compatible:
+ const: ti,sci-intr
+
+ ti,intr-trigger-type:
+ description: |
+ Should be one of the following.
+ 1 = If intr supports edge triggered interrupts.
+ 4 = If intr supports level triggered interrupts.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 1
+ description: |
+ The 1st cell should contain interrupt router input hw number.
+
+ ti,sci:
+ description: phandle to TI-SCI compatible System controller node
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/phandle
+
+ ti,sci-dev-id:
+ description: TI-SCI device id of Interrupt Controller
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+
+ ti,interrupt-ranges:
+ description: |
+ Interrupt ranges that converts the INTR output hw irq numbers
+ to parents's input interrupt numbers.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ - items:
+ items:
+ - description: |
+ "output_irq" specifies the base for intr output irq
+ - description: |
+ "parent's input irq" specifies the base for parent irq
+ - description: |
+ "limit" specifies the limit for translation
+
+required:
+ - compatible
+ - ti,intr-trigger-type
+ - interrupt-controller
+ - '#interrupt-cells'
+ - ti,sci
+ - ti,sci-dev-id
+ - ti,interrupt-ranges
+
+examples:
+ - |
+ main_gpio_intr: interrupt-controller0 {
+ compatible = "ti,sci-intr";
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <131>;
+ ti,interrupt-ranges = <0 360 32>;
+ };
@@ -16652,7 +16652,7 @@ S: Maintained
F: Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
F: Documentation/devicetree/bindings/clock/ti,sci-clk.txt
F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-inta.txt
-F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
+F: Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml
F: Documentation/devicetree/bindings/reset/ti,sci-reset.txt
F: Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
F: drivers/clk/keystone/sci-clk.c
In order to automate the verification of DT nodes convert ti,sci-intr.txt ti,sci-intr.yaml. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> --- .../interrupt-controller/ti,sci-intr.txt | 83 ------------- .../interrupt-controller/ti,sci-intr.yaml | 113 ++++++++++++++++++ MAINTAINERS | 2 +- 3 files changed, 114 insertions(+), 84 deletions(-) delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.yaml