@@ -395,6 +395,17 @@ config LEDS_LP3952
To compile this driver as a module, choose M here: the
module will be called leds-lp3952.
+config LEDS_LP50XX
+ tristate "LED Support for TI LP5036/30/24/18/12/9 LED driver chip"
+ depends on LEDS_CLASS && REGMAP_I2C
+ depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
+ help
+ If you say yes here you get support for the Texas Instruments
+ LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
+
+ To compile this driver as a module, choose M here: the
+ module will be called leds-lp50xx.
+
config LEDS_LP55XX_COMMON
tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
@@ -49,6 +49,7 @@ obj-$(CONFIG_LEDS_LM3697) += leds-lm3697.o
obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o
obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o
obj-$(CONFIG_LEDS_LP3952) += leds-lp3952.o
+obj-$(CONFIG_LEDS_LP50XX) += leds-lp50xx.o
obj-$(CONFIG_LEDS_LP5521) += leds-lp5521.o
obj-$(CONFIG_LEDS_LP5523) += leds-lp5523.o
obj-$(CONFIG_LEDS_LP5562) += leds-lp5562.o
new file mode 100644
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: GPL-2.0
+// TI LP50XX LED chip family driver
+// Copyright (C) 2018-20 Texas Instruments Incorporated - https://www.ti.com/
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <uapi/linux/uleds.h>
+
+#include <linux/led-class-multicolor.h>
+
+#include "leds.h"
+
+#define LP50XX_DEV_CFG0 0x00
+#define LP50XX_DEV_CFG1 0x01
+#define LP50XX_LED_CFG0 0x02
+
+/* LP5009 and LP5012 registers */
+#define LP5012_BNK_BRT 0x03
+#define LP5012_BNKA_CLR 0x04
+#define LP5012_BNKB_CLR 0x05
+#define LP5012_BNKC_CLR 0x06
+#define LP5012_LED0_BRT 0x07
+#define LP5012_OUT0_CLR 0x0b
+#define LP5012_RESET 0x17
+
+/* LP5018 and LP5024 registers */
+#define LP5024_BNK_BRT 0x03
+#define LP5024_BNKA_CLR 0x04
+#define LP5024_BNKB_CLR 0x05
+#define LP5024_BNKC_CLR 0x06
+#define LP5024_LED0_BRT 0x07
+#define LP5024_OUT0_CLR 0x0f
+#define LP5024_RESET 0x27
+
+/* LP5030 and LP5036 registers */
+#define LP5036_LED_CFG1 0x03
+#define LP5036_BNK_BRT 0x04
+#define LP5036_BNKA_CLR 0x05
+#define LP5036_BNKB_CLR 0x06
+#define LP5036_BNKC_CLR 0x07
+#define LP5036_LED0_BRT 0x08
+#define LP5036_OUT0_CLR 0x14
+#define LP5036_RESET 0x38
+
+#define LP50XX_SW_RESET 0xff
+#define LP50XX_CHIP_EN BIT(6)
+
+/* There are 3 LED outputs per bank */
+#define LP50XX_LEDS_PER_MODULE 3
+
+#define LP5009_MAX_LED_MODULES 2
+#define LP5012_MAX_LED_MODULES 4
+#define LP5018_MAX_LED_MODULES 6
+#define LP5024_MAX_LED_MODULES 8
+#define LP5030_MAX_LED_MODULES 10
+#define LP5036_MAX_LED_MODULES 12
+
+static const struct reg_default lp5012_reg_defs[] = {
+ {LP50XX_DEV_CFG0, 0x0},
+ {LP50XX_DEV_CFG1, 0x3c},
+ {LP50XX_LED_CFG0, 0x0},
+ {LP5012_BNK_BRT, 0xff},
+ {LP5012_BNKA_CLR, 0x0f},
+ {LP5012_BNKB_CLR, 0x0f},
+ {LP5012_BNKC_CLR, 0x0f},
+ {LP5012_LED0_BRT, 0x0f},
+ /* LEDX_BRT registers are all 0xff for defaults */
+ {0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff},
+ {LP5012_OUT0_CLR, 0x0f},
+ /* OUTX_CLR registers are all 0x0 for defaults */
+ {0x0c, 0x00}, {0x0d, 0x00}, {0x0e, 0x00}, {0x0f, 0x00}, {0x10, 0x00},
+ {0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00}, {0x15, 0x00},
+ {0x16, 0x00},
+ {LP5012_RESET, 0x00}
+};
+
+static const struct reg_default lp5024_reg_defs[] = {
+ {LP50XX_DEV_CFG0, 0x0},
+ {LP50XX_DEV_CFG1, 0x3c},
+ {LP50XX_LED_CFG0, 0x0},
+ {LP5024_BNK_BRT, 0xff},
+ {LP5024_BNKA_CLR, 0x0f},
+ {LP5024_BNKB_CLR, 0x0f},
+ {LP5024_BNKC_CLR, 0x0f},
+ {LP5024_LED0_BRT, 0x0f},
+ /* LEDX_BRT registers are all 0xff for defaults */
+ {0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+ {0x0d, 0xff}, {0x0e, 0xff},
+ {LP5024_OUT0_CLR, 0x0f},
+ /* OUTX_CLR registers are all 0x0 for defaults */
+ {0x10, 0x00}, {0x11, 0x00}, {0x12, 0x00}, {0x13, 0x00}, {0x14, 0x00},
+ {0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+ {0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+ {0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+ {0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00},
+ {LP5024_RESET, 0x00}
+};
+
+static const struct reg_default lp5036_reg_defs[] = {
+ {LP50XX_DEV_CFG0, 0x0},
+ {LP50XX_DEV_CFG1, 0x3c},
+ {LP50XX_LED_CFG0, 0x0},
+ {LP5036_LED_CFG1, 0x0},
+ {LP5036_BNK_BRT, 0xff},
+ {LP5036_BNKA_CLR, 0x0f},
+ {LP5036_BNKB_CLR, 0x0f},
+ {LP5036_BNKC_CLR, 0x0f},
+ {LP5036_LED0_BRT, 0x0f},
+ /* LEDX_BRT registers are all 0xff for defaults */
+ {0x08, 0xff}, {0x09, 0xff}, {0x0a, 0xff}, {0x0b, 0xff}, {0x0c, 0xff},
+ {0x0d, 0xff}, {0x0e, 0xff}, {0x0f, 0xff}, {0x10, 0xff}, {0x11, 0xff},
+ {0x12, 0xff}, {0x13, 0xff},
+ {LP5036_OUT0_CLR, 0x0f},
+ /* OUTX_CLR registers are all 0x0 for defaults */
+ {0x15, 0x00}, {0x16, 0x00}, {0x17, 0x00}, {0x18, 0x00}, {0x19, 0x00},
+ {0x1a, 0x00}, {0x1b, 0x00}, {0x1c, 0x00}, {0x1d, 0x00}, {0x1e, 0x00},
+ {0x1f, 0x00}, {0x20, 0x00}, {0x21, 0x00}, {0x22, 0x00}, {0x23, 0x00},
+ {0x24, 0x00}, {0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
+ {0x29, 0x00}, {0x2a, 0x00}, {0x2b, 0x00}, {0x2c, 0x00}, {0x2d, 0x00},
+ {0x2e, 0x00}, {0x2f, 0x00}, {0x30, 0x00}, {0x31, 0x00}, {0x32, 0x00},
+ {0x33, 0x00}, {0x34, 0x00}, {0x35, 0x00}, {0x36, 0x00}, {0x37, 0x00},
+ {LP5036_RESET, 0x00}
+};
+
+static const struct regmap_config lp5012_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = LP5012_RESET,
+ .reg_defaults = lp5012_reg_defs,
+ .num_reg_defaults = ARRAY_SIZE(lp5012_reg_defs),
+ .cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5024_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = LP5024_RESET,
+ .reg_defaults = lp5024_reg_defs,
+ .num_reg_defaults = ARRAY_SIZE(lp5024_reg_defs),
+ .cache_type = REGCACHE_FLAT,
+};
+
+static const struct regmap_config lp5036_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = LP5036_RESET,
+ .reg_defaults = lp5036_reg_defs,
+ .num_reg_defaults = ARRAY_SIZE(lp5036_reg_defs),
+ .cache_type = REGCACHE_FLAT,
+};
+
+enum lp50xx_model {
+ LP5009,
+ LP5012,
+ LP5018,
+ LP5024,
+ LP5030,
+ LP5036,
+};
+
+/**
+ * struct lp50xx_chip_info -
+ * @lp50xx_regmap_config: regmap register configuration
+ * @model_id: LED device model
+ * @max_modules: total number of supported LED modules
+ * @num_leds: number of LED outputs available on the device
+ * @led_brightness0_reg: first brightness register of the device
+ * @mix_out0_reg: first color mix register of the device
+ * @bank_brt_reg: bank brightness register
+ * @bank_mix_reg: color mix register
+ * @reset_reg: device reset register
+ */
+struct lp50xx_chip_info {
+ const struct regmap_config *lp50xx_regmap_config;
+ int model_id;
+ u8 max_modules;
+ u8 num_leds;
+ u8 led_brightness0_reg;
+ u8 mix_out0_reg;
+ u8 bank_brt_reg;
+ u8 bank_mix_reg;
+ u8 reset_reg;
+};
+
+static const struct lp50xx_chip_info lp50xx_chip_info_tbl[] = {
+ [LP5009] = {
+ .model_id = LP5009,
+ .max_modules = LP5009_MAX_LED_MODULES,
+ .num_leds = LP5009_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5012_LED0_BRT,
+ .mix_out0_reg = LP5012_OUT0_CLR,
+ .bank_brt_reg = LP5012_BNK_BRT,
+ .bank_mix_reg = LP5012_BNKA_CLR,
+ .reset_reg = LP5012_RESET,
+ .lp50xx_regmap_config = &lp5012_regmap_config,
+ },
+ [LP5012] = {
+ .model_id = LP5012,
+ .max_modules = LP5012_MAX_LED_MODULES,
+ .num_leds = LP5012_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5012_LED0_BRT,
+ .mix_out0_reg = LP5012_OUT0_CLR,
+ .bank_brt_reg = LP5012_BNK_BRT,
+ .bank_mix_reg = LP5012_BNKA_CLR,
+ .reset_reg = LP5012_RESET,
+ .lp50xx_regmap_config = &lp5012_regmap_config,
+ },
+ [LP5018] = {
+ .model_id = LP5018,
+ .max_modules = LP5018_MAX_LED_MODULES,
+ .num_leds = LP5018_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5024_LED0_BRT,
+ .mix_out0_reg = LP5024_OUT0_CLR,
+ .bank_brt_reg = LP5024_BNK_BRT,
+ .bank_mix_reg = LP5024_BNKA_CLR,
+ .reset_reg = LP5024_RESET,
+ .lp50xx_regmap_config = &lp5024_regmap_config,
+ },
+ [LP5024] = {
+ .model_id = LP5024,
+ .max_modules = LP5024_MAX_LED_MODULES,
+ .num_leds = LP5024_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5024_LED0_BRT,
+ .mix_out0_reg = LP5024_OUT0_CLR,
+ .bank_brt_reg = LP5024_BNK_BRT,
+ .bank_mix_reg = LP5024_BNKA_CLR,
+ .reset_reg = LP5024_RESET,
+ .lp50xx_regmap_config = &lp5024_regmap_config,
+ },
+ [LP5030] = {
+ .model_id = LP5030,
+ .max_modules = LP5030_MAX_LED_MODULES,
+ .num_leds = LP5030_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5036_LED0_BRT,
+ .mix_out0_reg = LP5036_OUT0_CLR,
+ .bank_brt_reg = LP5036_BNK_BRT,
+ .bank_mix_reg = LP5036_BNKA_CLR,
+ .reset_reg = LP5036_RESET,
+ .lp50xx_regmap_config = &lp5036_regmap_config,
+ },
+ [LP5036] = {
+ .model_id = LP5036,
+ .max_modules = LP5036_MAX_LED_MODULES,
+ .num_leds = LP5036_MAX_LED_MODULES * LP50XX_LEDS_PER_MODULE,
+ .led_brightness0_reg = LP5036_LED0_BRT,
+ .mix_out0_reg = LP5036_OUT0_CLR,
+ .bank_brt_reg = LP5036_BNK_BRT,
+ .bank_mix_reg = LP5036_BNKA_CLR,
+ .reset_reg = LP5036_RESET,
+ .lp50xx_regmap_config = &lp5036_regmap_config,
+ },
+};
+
+struct lp50xx_led {
+ struct led_classdev_mc mc_cdev;
+ struct lp50xx *priv;
+ unsigned long bank_modules;
+ int led_intensity[LP50XX_LEDS_PER_MODULE];
+ u8 ctrl_bank_enabled;
+ int led_number;
+};
+
+/**
+ * struct lp50xx -
+ * @enable_gpio: hardware enable gpio
+ * @regulator: LED supply regulator pointer
+ * @client: pointer to the I2C client
+ * @regmap: device register map
+ * @dev: pointer to the devices device struct
+ * @lock: lock for reading/writing the device
+ * @chip_info: chip specific information (ie num_leds)
+ * @num_of_banked_leds: holds the number of banked LEDs
+ * @leds: array of LED strings
+ */
+struct lp50xx {
+ struct gpio_desc *enable_gpio;
+ struct regulator *regulator;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct device *dev;
+ struct mutex lock;
+ const struct lp50xx_chip_info *chip_info;
+ int num_of_banked_leds;
+
+ /* This needs to be at the end of the struct */
+ struct lp50xx_led leds[];
+};
+
+static struct lp50xx_led *mcled_cdev_to_led(struct led_classdev_mc *mc_cdev)
+{
+ return container_of(mc_cdev, struct lp50xx_led, mc_cdev);
+}
+
+static int lp50xx_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct led_classdev_mc *mc_dev = lcdev_to_mccdev(cdev);
+ struct lp50xx_led *led = mcled_cdev_to_led(mc_dev);
+ const struct lp50xx_chip_info *led_chip = led->priv->chip_info;
+ u8 led_offset, reg_val;
+ int ret = 0;
+ int i;
+
+ mutex_lock(&led->priv->lock);
+ if (led->ctrl_bank_enabled)
+ reg_val = led_chip->bank_brt_reg;
+ else
+ reg_val = led_chip->led_brightness0_reg +
+ led->led_number;
+
+ ret = regmap_write(led->priv->regmap, reg_val, brightness);
+ if (ret) {
+ dev_err(&led->priv->client->dev,
+ "Cannot write brightness value %d\n", ret);
+ goto out;
+ }
+
+ for (i = 0; i < led->mc_cdev.num_colors; i++) {
+ if (led->ctrl_bank_enabled) {
+ reg_val = led_chip->bank_mix_reg + i;
+ } else {
+ led_offset = (led->led_number * 3) + i;
+ reg_val = led_chip->mix_out0_reg + led_offset;
+ }
+
+ ret = regmap_write(led->priv->regmap, reg_val,
+ mc_dev->subled_info[i].intensity);
+ if (ret) {
+ dev_err(&led->priv->client->dev,
+ "Cannot write intensity value %d\n", ret);
+ goto out;
+ }
+ }
+out:
+ mutex_unlock(&led->priv->lock);
+ return ret;
+}
+
+static int lp50xx_set_banks(struct lp50xx *priv, u32 led_banks[])
+{
+ u8 led_config_lo, led_config_hi;
+ u32 bank_enable_mask = 0;
+ int ret;
+ int i;
+
+ for (i = 0; i < priv->chip_info->max_modules; i++) {
+ if (led_banks[i])
+ bank_enable_mask |= (1 << led_banks[i]);
+ }
+
+ led_config_lo = (u8)(bank_enable_mask & 0xff);
+ led_config_hi = (u8)(bank_enable_mask >> 8) & 0xff;
+
+ ret = regmap_write(priv->regmap, LP50XX_LED_CFG0, led_config_lo);
+ if (ret)
+ return ret;
+
+ if (priv->chip_info->model_id >= LP5030)
+ ret = regmap_write(priv->regmap, LP5036_LED_CFG1, led_config_hi);
+
+ return ret;
+}
+
+static int lp50xx_reset(struct lp50xx *priv)
+{
+ return regmap_write(priv->regmap, priv->chip_info->reset_reg, LP50XX_SW_RESET);
+}
+
+static int lp50xx_enable_disable(struct lp50xx *priv, int enable_disable)
+{
+ int ret;
+
+ if (priv->enable_gpio) {
+ ret = gpiod_direction_output(priv->enable_gpio, enable_disable);
+ if (ret)
+ return ret;
+ }
+
+ if (enable_disable)
+ return regmap_write(priv->regmap, LP50XX_DEV_CFG0, LP50XX_CHIP_EN);
+ else
+ return regmap_write(priv->regmap, LP50XX_DEV_CFG0, 0);
+
+}
+
+static int lp50xx_probe_leds(struct fwnode_handle *child, struct lp50xx *priv,
+ struct lp50xx_led *led, int num_leds)
+{
+ u32 led_banks[LP5036_MAX_LED_MODULES] = {0};
+ int led_number;
+ int ret;
+
+ if (num_leds > 1) {
+ if (num_leds > priv->chip_info->max_modules) {
+ dev_err(&priv->client->dev, "reg property is invalid\n");
+ return -EINVAL;
+ }
+
+ priv->num_of_banked_leds = num_leds;
+
+ ret = fwnode_property_read_u32_array(child, "reg", led_banks, num_leds);
+ if (ret) {
+ dev_err(&priv->client->dev, "reg property is missing\n");
+ return ret;
+ }
+
+ ret = lp50xx_set_banks(priv, led_banks);
+ if (ret) {
+ dev_err(&priv->client->dev, "Cannot setup banked LEDs\n");
+ return ret;
+ }
+
+ led->ctrl_bank_enabled = 1;
+ } else {
+ ret = fwnode_property_read_u32(child, "reg", &led_number);
+ if (ret) {
+ dev_err(&priv->client->dev, "led reg property missing\n");
+ return ret;
+ }
+
+ if (led_number > priv->chip_info->num_leds) {
+ dev_err(&priv->client->dev, "led-sources property is invalid\n");
+ return -EINVAL;
+ }
+
+ led->led_number = led_number;
+ }
+
+ return 0;
+}
+
+static int lp50xx_probe_dt(struct lp50xx *priv)
+{
+ struct fwnode_handle *child = NULL;
+ struct fwnode_handle *led_node = NULL;
+ struct led_init_data init_data = {};
+ struct led_classdev *led_cdev;
+ struct mc_subled *mc_led_info;
+ struct lp50xx_led *led;
+ int ret = -EINVAL;
+ int num_colors;
+ u32 color_id;
+ int i = 0;
+
+ priv->enable_gpio = devm_gpiod_get_optional(priv->dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(priv->enable_gpio)) {
+ ret = PTR_ERR(priv->enable_gpio);
+ dev_err(&priv->client->dev, "Failed to get enable gpio: %d\n",
+ ret);
+ return ret;
+ }
+
+ priv->regulator = devm_regulator_get(priv->dev, "vled");
+ if (IS_ERR(priv->regulator))
+ priv->regulator = NULL;
+
+ device_for_each_child_node(priv->dev, child) {
+ led = &priv->leds[i];
+ ret = fwnode_property_count_u32(child, "reg");
+ if (ret < 0) {
+ dev_err(&priv->client->dev, "reg property is invalid\n");
+ goto child_out;
+ }
+
+ ret = lp50xx_probe_leds(child, priv, led, ret);
+ if (ret)
+ goto child_out;
+
+ init_data.fwnode = child;
+ num_colors = 0;
+
+ /*
+ * There are only 3 LEDs per module otherwise they should be
+ * banked which also is presented as 3 LEDs.
+ */
+ mc_led_info = devm_kcalloc(priv->dev, LP50XX_LEDS_PER_MODULE,
+ sizeof(*mc_led_info), GFP_KERNEL);
+ if (!mc_led_info)
+ return -ENOMEM;
+
+ fwnode_for_each_child_node(child, led_node) {
+ ret = fwnode_property_read_u32(led_node, "color",
+ &color_id);
+ if (ret) {
+ dev_err(priv->dev, "Cannot read color\n");
+ goto child_out;
+ }
+
+ mc_led_info[num_colors].color_index = color_id;
+ num_colors++;
+ }
+
+ led->priv = priv;
+ led->mc_cdev.num_colors = num_colors;
+ led->mc_cdev.subled_info = mc_led_info;
+ led_cdev = &led->mc_cdev.led_cdev;
+ led_cdev->brightness_set_blocking = lp50xx_brightness_set;
+
+ fwnode_property_read_string(child, "linux,default-trigger",
+ &led_cdev->default_trigger);
+
+ ret = devm_led_classdev_multicolor_register_ext(&priv->client->dev,
+ &led->mc_cdev,
+ &init_data);
+ if (ret) {
+ dev_err(&priv->client->dev, "led register err: %d\n",
+ ret);
+ goto child_out;
+ }
+ i++;
+ fwnode_handle_put(child);
+ }
+
+ return 0;
+
+child_out:
+ fwnode_handle_put(child);
+ return ret;
+}
+
+static int lp50xx_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct lp50xx *led;
+ int count;
+ int ret;
+
+ count = device_get_child_node_count(&client->dev);
+ if (!count) {
+ dev_err(&client->dev, "LEDs are not defined in device tree!");
+ return -ENODEV;
+ }
+
+ led = devm_kzalloc(&client->dev, struct_size(led, leds, count),
+ GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ mutex_init(&led->lock);
+ led->client = client;
+ led->dev = &client->dev;
+ led->chip_info = &lp50xx_chip_info_tbl[id->driver_data];
+ i2c_set_clientdata(client, led);
+ led->regmap = devm_regmap_init_i2c(client,
+ led->chip_info->lp50xx_regmap_config);
+ if (IS_ERR(led->regmap)) {
+ ret = PTR_ERR(led->regmap);
+ dev_err(&client->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = lp50xx_reset(led);
+ if (ret)
+ return ret;
+
+ ret = lp50xx_enable_disable(led, 1);
+ if (ret)
+ return ret;
+
+ return lp50xx_probe_dt(led);
+}
+
+static int lp50xx_remove(struct i2c_client *client)
+{
+ struct lp50xx *led = i2c_get_clientdata(client);
+ int ret;
+
+ ret = lp50xx_enable_disable(led, 0);
+ if (ret) {
+ dev_err(&led->client->dev, "Failed to disable chip\n");
+ return ret;
+ }
+
+ if (led->regulator) {
+ ret = regulator_disable(led->regulator);
+ if (ret)
+ dev_err(&led->client->dev,
+ "Failed to disable regulator\n");
+ }
+
+ mutex_destroy(&led->lock);
+
+ return 0;
+}
+
+static const struct i2c_device_id lp50xx_id[] = {
+ { "lp5009", LP5009 },
+ { "lp5012", LP5012 },
+ { "lp5018", LP5018 },
+ { "lp5024", LP5024 },
+ { "lp5030", LP5030 },
+ { "lp5036", LP5036 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lp50xx_id);
+
+static const struct of_device_id of_lp50xx_leds_match[] = {
+ { .compatible = "ti,lp5009", .data = (void *)LP5009 },
+ { .compatible = "ti,lp5012", .data = (void *)LP5012 },
+ { .compatible = "ti,lp5018", .data = (void *)LP5018 },
+ { .compatible = "ti,lp5024", .data = (void *)LP5024 },
+ { .compatible = "ti,lp5030", .data = (void *)LP5030 },
+ { .compatible = "ti,lp5036", .data = (void *)LP5036 },
+ {},
+};
+MODULE_DEVICE_TABLE(of, of_lp50xx_leds_match);
+
+static struct i2c_driver lp50xx_driver = {
+ .driver = {
+ .name = "lp50xx",
+ .of_match_table = of_lp50xx_leds_match,
+ },
+ .probe = lp50xx_probe,
+ .remove = lp50xx_remove,
+ .id_table = lp50xx_id,
+};
+module_i2c_driver(lp50xx_driver);
+
+MODULE_DESCRIPTION("Texas Instruments LP50XX LED driver");
+MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
+MODULE_LICENSE("GPL v2");