| Message ID | 20200908162252.17672-6-lokeshvutla@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | arm64: Initial support for Texas Instrument's J7200 Platform | expand |
On 21:52-20200908, Lokesh Vutla wrote: > Add support for J7200 Common Processor Board. > The EVM architecture is very similar to J721E as follows: > > +------------------------------------------------------+ > | +-------------------------------------------+ | > | | | | > | | Add-on Card 1 Options | | > | | | | > | +-------------------------------------------+ | > | | > | | > | +-------------------+ | > | | | | > | | SOM | | > | +--------------+ | | | > | | | | | | > | | Add-on | +-------------------+ | > | | Card 2 | | Power Supply > | | Options | | | > | | | | | > | +--------------+ | <--- > +------------------------------------------------------+ > Common Processor Board > > Common Processor board is the baseboard that has most of the actual > connectors, power supply etc. A SOM (System on Module) is plugged on > to the common processor board and this contains the SoC, PMIC, DDR and > basic high speed components necessary for functionality. > > Note: > * The minimum configuration required to boot up the board is System On > Module(SOM) + Common Processor Board. > * Since there is just a single SOM and Common Processor Board, we are > maintaining common processor board as the base dts and SOM as the dtsi > that we include. In the future as more SOM's appear, we should move > common processor board as a dtsi and include configurations as dts. > * All daughter cards beyond the basic boards shall be maintained as > overlays. > > Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> > Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> > Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> > --- > arch/arm64/boot/dts/ti/Makefile | 2 + > .../dts/ti/k3-j7200-common-proc-board.dts | 64 +++++++++++++++++++ > arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 29 +++++++++ > 3 files changed, 95 insertions(+) > create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi This looks fine to me.
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index e7bfb16fa816..ae76b0cb1fbf 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -9,3 +9,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb + +dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts new file mode 100644 index 000000000000..e27069317c4e --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include "k3-j7200-som-p0.dtsi" + +/ { + chosen { + stdout-path = "serial2:115200n8"; + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + }; +}; + +&wkup_uart0 { + /* Wakeup UART is used by System firmware */ + status = "disabled"; +}; + +&main_uart0 { + power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; +}; + +&main_uart2 { + /* MAIN UART 2 is used by R5F firmware */ + status = "disabled"; +}; + +&main_uart3 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart4 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart5 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart6 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart7 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart8 { + /* UART not brought out */ + status = "disabled"; +}; + +&main_uart9 { + /* UART not brought out */ + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi new file mode 100644 index 000000000000..22fc50bd5c4c --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include "k3-j7200.dtsi" + +/ { + memory@80000000 { + device_type = "memory"; + /* 4G RAM */ + reg = <0x00 0x80000000 0x00 0x80000000>, + <0x08 0x80000000 0x00 0x80000000>; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; + alignment = <0x1000>; + no-map; + }; + }; +};
Add support for J7200 Common Processor Board. The EVM architecture is very similar to J721E as follows: +------------------------------------------------------+ | +-------------------------------------------+ | | | | | | | Add-on Card 1 Options | | | | | | | +-------------------------------------------+ | | | | | | +-------------------+ | | | | | | | SOM | | | +--------------+ | | | | | | | | | | | Add-on | +-------------------+ | | | Card 2 | | Power Supply | | Options | | | | | | | | | +--------------+ | <--- +------------------------------------------------------+ Common Processor Board Common Processor board is the baseboard that has most of the actual connectors, power supply etc. A SOM (System on Module) is plugged on to the common processor board and this contains the SoC, PMIC, DDR and basic high speed components necessary for functionality. Note: * The minimum configuration required to boot up the board is System On Module(SOM) + Common Processor Board. * Since there is just a single SOM and Common Processor Board, we are maintaining common processor board as the base dts and SOM as the dtsi that we include. In the future as more SOM's appear, we should move common processor board as a dtsi and include configurations as dts. * All daughter cards beyond the basic boards shall be maintained as overlays. Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- arch/arm64/boot/dts/ti/Makefile | 2 + .../dts/ti/k3-j7200-common-proc-board.dts | 64 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 29 +++++++++ 3 files changed, 95 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi