diff mbox series

[7/7] ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera

Message ID 20200923010215.148819-2-icenowy@aosc.io
State New
Headers show
Series Pine64 PineCube support | expand

Commit Message

Icenowy Zheng Sept. 23, 2020, 1:02 a.m. UTC
The Pine64 PineCube IP camera is an IP camera with SoChip S3 SoC.

It comes with a main board, an expansion board and a camera.

The main board features a Micro-USB power-only jack, a USB Type-A port,
an Ethernet port connected to the internal PHY of the SoC and a Realtek
RTL8189ES SDIO Wi-Fi module. A RGB LCD connector is reserved on the
board.

The expansion board features a TF slot, a microphone, a speaker
connector with on-board amplifier and a few IR LEDs.

Add support for the kit, with features on the main board and the
expansion board now.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/sun8i-s3-pinecube.dts | 235 ++++++++++++++++++++++++
 2 files changed, 236 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-s3-pinecube.dts
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e7c59d0c8598..b163c8f1cefc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1198,6 +1198,7 @@  dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-r16-parrot.dtb \
 	sun8i-r40-bananapi-m2-ultra.dtb \
 	sun8i-s3-lichee-zero-plus.dtb \
+	sun8i-s3-pinecube.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
 	sun8i-v3s-licheepi-zero-dock.dtb \
diff --git a/arch/arm/boot/dts/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/sun8i-s3-pinecube.dts
new file mode 100644
index 000000000000..9bab6b7f4014
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-s3-pinecube.dts
@@ -0,0 +1,235 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2019 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "sun8i-v3.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "PineCube IP Camera";
+	compatible = "pine64,pinecube", "allwinner,sun8i-s3";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "pine64:ir:led1";
+			gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
+		};
+
+		led2 {
+			label = "pine64:ir:led2";
+			gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */
+		};
+	};
+
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_wifi: vcc-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-wifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */
+		vin-supply = <&reg_dcdc3>;
+		startup-delay-us = <200000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&csi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&csi1_8bit_pins>;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		csi1_ep: endpoint {
+			remote-endpoint = <&ov5640_ep>;
+			bus-width = <8>;
+			hsync-active = <1>; /* Active high */
+			vsync-active = <0>; /* Active low */
+			data-active = <1>;  /* Active high */
+			pclk-sample = <1>;  /* Rising */
+		};
+	};
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		compatible = "x-powers,axp203",
+			     "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pe_pins>;
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&csi1_mclk_pin>;
+		clocks = <&ccu CLK_CSI1_MCLK>;
+		clock-names = "xclk";
+
+		AVDD-supply = <&reg_ldo3>;
+		DOVDD-supply = <&reg_ldo3>;
+		DVDD-supply = <&reg_ldo4>;
+		reset-gpios = <&pio 4 23 GPIO_ACTIVE_LOW>; /* PE23 */
+		powerdown-gpios = <&pio 4 24 GPIO_ACTIVE_HIGH>; /* PE24 */
+
+		port {
+			ov5640_ep: endpoint {
+				remote-endpoint = <&csi1_ep>;
+				bus-width = <8>;
+				hsync-active = <1>; /* Active high */
+				vsync-active = <0>; /* Active low */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-200 {
+		label = "Setup";
+		linux,code = <KEY_SETUP>;
+		channel = <0>;
+		voltage = <190000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdc3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc_wifi>;
+	vqmmc-supply = <&reg_dcdc3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pd-supply = <&reg_dcdc3>;
+	vcc-pe-supply = <&reg_ldo3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-sys-cpu-ephy";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-dovdd-2v8-csi";
+	regulator-soft-start;
+	regulator-ramp-delay = <1600>;
+};
+
+&reg_ldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-1v8-csi";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};