diff mbox series

[v4,1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards

Message ID 20201001150217.31301-1-frieder.schrempf@kontron.de (mailing list archive)
State New, archived
Headers show
Series [v4,1/2] arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards | expand

Commit Message

Frieder Schrempf Oct. 1, 2020, 3:01 p.m. UTC 
From: Frieder Schrempf <frieder.schrempf@kontron.de>

Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.

The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes for v4:
* Remove one more needless status property
* Use local-mac-address instead of mac-address
* Add missing pinctrl-names in PMIC node
* Fix interrupt flags in PMIC node
* Use lowercase regulator names
* Enable pullup for PMIC IRQ line
* Fix pinctrl grp names to match schema

Changes for v3:
* Remove needless status properties
* Remove needless regulator properties for reg_vdd_5v
* Use proper PHY reset properties in PHY node
* Use phy-connection-type instead of phy-mode
* Adjust PMIC node name and label
* Add over-current-active-low to usbotg1 node
* Remove redundant bus-width property from usdhc2 node
* Remove needless regulator-compatible from reg_vdd_snvs
* Set minimum voltage to 85mV for reg_vdd_snvs

Changes for v2:
* Make the licensing less strict (GPL-2.0+ OR MIT)
* Merge the SoM and baseboard DTs for N8010 and N8011 into one as
  they only differ in DDR and eMMC size.
* Change compatibles and model strings to "n810x" and "N8010X".
* Only use a common memory node that will be updated by the
  bootloader reflecting the detected DDR size.
* Improve naming for 16MHz CAN fixed oscillator and set
  "clock-output-names".
* Consistently use "reg_" prefix for regulators.
* Remove "userspi" node.
* Slightly improve commit message.
---
 .../dts/freescale/imx8mm-kontron-n801x-s.dts  | 322 ++++++++++++++++++
 .../freescale/imx8mm-kontron-n801x-som.dtsi   | 294 ++++++++++++++++
 2 files changed, 616 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
new file mode 100644
index 000000000000..d17abb515835
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -0,0 +1,322 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-n801x-som.dtsi"
+
+/ {
+	model = "Kontron i.MX8MM N801X S";
+	compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+
+	aliases {
+		ethernet1 = &usbnet;
+	};
+
+	/* fixed crystal dedicated to mcp2515 */
+	osc_can: clock-osc-can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+		clock-output-names = "osc-can";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led3 {
+			label = "led3";
+			gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led4 {
+			label = "led4";
+			gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led5 {
+			label = "led5";
+			gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
+		};
+
+		led6 {
+			label = "led6";
+			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm2 0 5000 0>;
+	};
+
+	reg_rst_eth2: regulator-rst-eth2 {
+		compatible = "regulator-fixed";
+		regulator-name = "rst-usb-eth2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_eth2>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_vdd_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	can0: can@0 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can>;
+		clocks = <&osc_can>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		spi-max-frequency = <100000>;
+		vdd-supply = <&reg_vdd_3v3>;
+		xceiver-supply = <&reg_vdd_5v>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rgmii";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			reg = <0>;
+			reset-assert-us = <100>;
+			reset-deassert-us = <100>;
+			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbnet: usbether@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio>;
+
+	pinctrl_can: cangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19 /* PHY RST */
+			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x19 /* ETH IRQ */
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19
+			MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x19
+			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x19
+			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x19
+			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x19
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x19
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x19
+		>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_usb_eth2: usbeth2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
new file mode 100644
index 000000000000..d0456daefda8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -0,0 +1,294 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Kontron i.MX8MM N801X SoM";
+	compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*
+		 * There are multiple SoM flavors with different DDR sizes.
+		 * The smallest is 1GB. For larger sizes the bootloader will
+		 * update the reg property.
+		 */
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	spi-flash@0 {
+		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+		spi-max-frequency = <80000000>;
+		reg = <0>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdda: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+};
+
+&uart3 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};