diff mbox series

[v5,4/5] ARM: dts: exynos: Add Ethernet to Artik 5 board

Message ID 20201103151536.26472-5-l.stelmach@samsung.com (mailing list archive)
State New, archived
Headers show
Series AX88796C SPI Ethernet Adapter | expand

Commit Message

Lukasz Stelmach Nov. 3, 2020, 3:15 p.m. UTC 
Add node for ax88796c ethernet chip.

Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
---
 arch/arm/boot/dts/exynos3250-artik5-eval.dts | 29 ++++++++++++++++++++
 1 file changed, 29 insertions(+)

Comments

Krzysztof Kozlowski Nov. 6, 2020, 7:39 p.m. UTC | #1 
On Tue, Nov 03, 2020 at 04:15:35PM +0100, Łukasz Stelmach wrote:
> Add node for ax88796c ethernet chip.
> 
> Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
> ---
>  arch/arm/boot/dts/exynos3250-artik5-eval.dts | 29 ++++++++++++++++++++
>  1 file changed, 29 insertions(+)

Thanks, applied.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/exynos3250-artik5-eval.dts b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
index 20446a846a98..a91e09a7d3fa 100644
--- a/arch/arm/boot/dts/exynos3250-artik5-eval.dts
+++ b/arch/arm/boot/dts/exynos3250-artik5-eval.dts
@@ -37,3 +37,32 @@  &mshc_2 {
 &serial_2 {
 	status = "okay";
 };
+
+&spi_0 {
+	status = "okay";
+	cs-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>, <0>;
+
+	assigned-clocks = <&cmu CLK_MOUT_MPLL>, <&cmu CLK_DIV_MPLL_PRE>,
+		<&cmu CLK_MOUT_SPI0>, <&cmu CLK_DIV_SPI0>,
+		<&cmu CLK_DIV_SPI0_PRE>, <&cmu CLK_SCLK_SPI0>;
+	assigned-clock-parents =
+		<&cmu CLK_FOUT_MPLL>,    /* for: CLK_MOUT_MPLL */
+		<&cmu CLK_MOUT_MPLL>,	 /* for: CLK_DIV_MPLL_PRE */
+		<&cmu CLK_DIV_MPLL_PRE>, /* for: CLK_MOUT_SPI0 */
+		<&cmu CLK_MOUT_SPI0>,    /* for: CLK_DIV_SPI0 */
+		<&cmu CLK_DIV_SPI0>,     /* for: CLK_DIV_SPI0_PRE */
+		<&cmu CLK_DIV_SPI0_PRE>; /* for: CLK_SCLK_SPI0 */
+
+	ethernet@0 {
+		compatible = "asix,ax88796c";
+		reg = <0x0>;
+		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a boot-loader */
+		interrupt-parent = <&gpx2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <40000000>;
+		reset-gpios = <&gpe0 2 GPIO_ACTIVE_LOW>;
+		controller-data {
+			samsung,spi-feedback-delay = <2>;
+		};
+	};
+};