diff mbox series

[v5,2/3] PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192

Message ID 20201202133813.6917-3-jianjun.wang@mediatek.com (mailing list archive)
State New, archived
Headers show
Series PCI: mediatek: Add new generation controller support | expand

Commit Message

Jianjun Wang (王建军) Dec. 2, 2020, 1:38 p.m. UTC
MediaTek's PCIe host controller has three generation HWs, the new
generation HW is an individual bridge, it supports Gen3 speed and
up to 256 MSI interrupt numbers for multi-function devices.

Add support for new Gen3 controller which can be found on MT8192.

Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
---
This patch dependents on "PCI: Export pci_pio_to_address() for module use"[1]
to build as a kernel module.

This interface will be used by PCI host drivers for PIO translation,
export it to support compiling those drivers as kernel modules.

[1]http://lists.infradead.org/pipermail/linux-mediatek/2020-December/019504.html
---
 drivers/pci/controller/Kconfig              |   13 +
 drivers/pci/controller/Makefile             |    1 +
 drivers/pci/controller/pcie-mediatek-gen3.c | 1039 +++++++++++++++++++
 3 files changed, 1053 insertions(+)
 create mode 100644 drivers/pci/controller/pcie-mediatek-gen3.c

Comments

Nicolas Boichat Dec. 21, 2020, 2:18 a.m. UTC | #1
On Wed, Dec 2, 2020 at 9:39 PM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
>
> MediaTek's PCIe host controller has three generation HWs, the new
> generation HW is an individual bridge, it supports Gen3 speed and
> up to 256 MSI interrupt numbers for multi-function devices.
>
> Add support for new Gen3 controller which can be found on MT8192.
>
> Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
> Acked-by: Ryder Lee <ryder.lee@mediatek.com>

FWIW, I looked at Rob and Bjorn's comments on v4, and they seem to
have been addressed (with one small nit highlighted below).

> ---
> This patch dependents on "PCI: Export pci_pio_to_address() for module use"[1]
> to build as a kernel module.
>
> This interface will be used by PCI host drivers for PIO translation,
> export it to support compiling those drivers as kernel modules.
>
> [1]http://lists.infradead.org/pipermail/linux-mediatek/2020-December/019504.html
> ---
>  drivers/pci/controller/Kconfig              |   13 +
>  drivers/pci/controller/Makefile             |    1 +
>  drivers/pci/controller/pcie-mediatek-gen3.c | 1039 +++++++++++++++++++
>  3 files changed, 1053 insertions(+)
>  create mode 100644 drivers/pci/controller/pcie-mediatek-gen3.c
>
> [snip]
> diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
> new file mode 100644
> index 000000000000..d30ea734ac0a
> --- /dev/null
> +++ b/drivers/pci/controller/pcie-mediatek-gen3.c
> @@ -0,0 +1,1039 @@
> [snip]
> +static int mtk_pcie_set_trans_table(struct mtk_pcie_port *port,
> +                                   resource_size_t cpu_addr,
> +                                   resource_size_t pci_addr,
> +                                   resource_size_t size,
> +                                   unsigned long type, int num)
> +{
> +       void __iomem *table;
> +       u32 val = 0;

You don't need to init val to 0.

> +
> +       if (num >= PCIE_MAX_TRANS_TABLES) {
> +               dev_notice(port->dev, "not enough translate table[%d] for addr: %#llx, limited to [%d]\n",
> +                          num, (unsigned long long) cpu_addr,
> +                          PCIE_MAX_TRANS_TABLES);
> +               return -ENODEV;
> +       }
> +
> +       table = port->base + PCIE_TRANS_TABLE_BASE_REG +
> +               num * PCIE_ATR_TLB_SET_OFFSET;
> +
> +       writel(lower_32_bits(cpu_addr) | PCIE_ATR_SIZE(fls(size) - 1), table);
> +       writel(upper_32_bits(cpu_addr), table + PCIE_ATR_SRC_ADDR_MSB_OFFSET);
> +       writel(lower_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_LSB_OFFSET);
> +       writel(upper_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_MSB_OFFSET);
> +
> +       if (type == IORESOURCE_IO)
> +               val = PCIE_ATR_TYPE_IO | PCIE_ATR_TLP_TYPE_IO;
> +       else
> +               val = PCIE_ATR_TYPE_MEM | PCIE_ATR_TLP_TYPE_MEM;
> +
> +       writel(val, table + PCIE_ATR_TRSL_PARAM_OFFSET);
> +
> +       return 0;
> +}
> +
> +static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
> +{
> +       struct resource_entry *entry;
> +       struct pci_host_bridge *host = pci_host_bridge_from_priv(port);
> +       unsigned int table_index = 0;
> +       int err;
> +       u32 val;
> +
> +       /* Set as RC mode */
> +       val = readl(port->base + PCIE_SETTING_REG);
> +       val |= PCIE_RC_MODE;
> +       writel(val, port->base + PCIE_SETTING_REG);
> +
> +       /* Set class code */
> +       val = readl(port->base + PCIE_PCI_IDS_1);
> +       val &= ~GENMASK(31, 8);
> +       val |= PCI_CLASS(PCI_CLASS_BRIDGE_PCI << 8);
> +       writel(val, port->base + PCIE_PCI_IDS_1);
> +
> +       /* Assert all reset signals */
> +       val = readl(port->base + PCIE_RST_CTRL_REG);
> +       val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB;
> +       writel(val, port->base + PCIE_RST_CTRL_REG);
> +
> +       /* De-assert reset signals */
> +       val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB);
> +       writel(val, port->base + PCIE_RST_CTRL_REG);
> +
> +       /* Delay 100ms to wait the reference clocks become stable */
> +       usleep_range(100 * 1000, 120 * 1000);

Any reason not to use msleep(100)?

> +
> +       /* De-assert PERST# signal */
> +       val &= ~PCIE_PE_RSTB;
> +       writel(val, port->base + PCIE_RST_CTRL_REG);
> +
> +       /* Check if the link is up or not */
> +       err = readl_poll_timeout(port->base + PCIE_LINK_STATUS_REG, val,
> +                       !!(val & PCIE_PORT_LINKUP), 20,
> +                       50 * USEC_PER_MSEC);
> +       if (err) {
> +               val = readl(port->base + PCIE_LTSSM_STATUS_REG);
> +               dev_notice(port->dev, "PCIe link down, ltssm reg val: %#x\n",
> +                          val);
> +               return err;
> +       }
> +
> +       /* Set PCIe translation windows */
> +       resource_list_for_each_entry(entry, &host->windows) {
> +               struct resource *res = entry->res;
> +               unsigned long type = resource_type(res);
> +               resource_size_t cpu_addr;
> +               resource_size_t pci_addr;
> +               resource_size_t size;
> +               const char *range_type;
> +
> +               if (type == IORESOURCE_IO) {
> +                       cpu_addr = pci_pio_to_address(res->start);
> +                       range_type = "IO";
> +               } else if (type == IORESOURCE_MEM) {
> +                       cpu_addr = res->start;
> +                       range_type = "MEM";
> +               } else {
> +                       continue;
> +               }
> +
> +               pci_addr = res->start - entry->offset;
> +               size = resource_size(res);
> +               err = mtk_pcie_set_trans_table(port, cpu_addr, pci_addr, size,
> +                                              type, table_index);
> +               if (err)
> +                       return err;
> +
> +               dev_dbg(port->dev, "set %s trans window[%d]: cpu_addr = %#llx, pci_addr = %#llx, size = %#llx\n",
> +                       range_type, table_index, (unsigned long long) cpu_addr,
> +                       (unsigned long long) pci_addr,
> +                       (unsigned long long) size);
> +
> +               table_index++;
> +       }
> +
> +       return 0;
> +}
> +
> [snip]
> +static irq_hw_number_t mtk_pcie_msi_get_hwirq(struct msi_domain_info *info,
> +                                             msi_alloc_info_t *arg)
> +{
> +       struct msi_desc *entry = arg->desc;
> +       struct mtk_pcie_port *port = info->chip_data;
> +       int hwirq;
> +
> +       mutex_lock(&port->lock);
> +
> +       hwirq = bitmap_find_free_region(port->msi_irq_in_use, PCIE_MSI_IRQS_NUM,
> +                                       order_base_2(entry->nvec_used));
> +       if (hwirq < 0) {
> +               mutex_unlock(&port->lock);
> +               return -ENOSPC;
> +       }
> +
> +       mutex_unlock(&port->lock);
> +
> +       return hwirq;

Code is good, but I had to look twice to make sure the mutex is
unlocked. Is the following marginally better?

hwirq = ...;

mutex_unlock(&port->lock);

if (hwirq < 0)
   return -ENOSPC;

return hwirq;

> +}
> +
> [snip]
> +static void mtk_pcie_msi_handler(struct irq_desc *desc)
> +{
> +       struct mtk_pcie_msi *msi_info = irq_desc_get_handler_data(desc);
> +       struct irq_chip *irqchip = irq_desc_get_chip(desc);
> +       unsigned long msi_enable, msi_status;
> +       unsigned int virq;
> +       irq_hw_number_t bit, hwirq;
> +
> +       chained_irq_enter(irqchip, desc);
> +
> +       msi_enable = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
> +       while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET))) {
> +               msi_status &= msi_enable;

I don't know much about MSI, but what happens if you have a bit that
is set in PCIE_MSI_STATUS_OFFSET register, but not in msi_enable?
Sounds like you'll just spin-loop forever without acknowledging the
interrupt.

> +               for_each_set_bit(bit, &msi_status, PCIE_MSI_IRQS_PER_SET) {
> +                       hwirq = bit + msi_info->index * PCIE_MSI_IRQS_PER_SET;
> +                       virq = irq_find_mapping(msi_info->domain, hwirq);
> +                       generic_handle_irq(virq);
> +               }
> +       }
> +
> +       chained_irq_exit(irqchip, desc);
> +}
> +
> [snip]
> +static int __maybe_unused mtk_pcie_suspend_noirq(struct device *dev)
> +{
> +       struct mtk_pcie_port *port = dev_get_drvdata(dev);
> +       int err;
> +       u32 val;
> +
> +       /* Trigger link to L2 state */
> +       err = mtk_pcie_turn_off_link(port);
> +       if (err) {
> +               dev_notice(port->dev, "can not enter L2 state\n");

Rob suggested dev_error here.

(and IMHO, or lot of the other dev_notice above should probably get dev_error)

> +               return err;
> +       }
> +
> +       /* Pull down the PERST# pin */
> +       val = readl(port->base + PCIE_RST_CTRL_REG);
> +       val |= PCIE_PE_RSTB;
> +       writel(val, port->base + PCIE_RST_CTRL_REG);
> +
> +       dev_dbg(port->dev, "enter L2 state success");
> +
> +       clk_bulk_disable_unprepare(port->num_clks, port->clks);
> +
> +       phy_power_off(port->phy);
> +
> +       return 0;
> +}
> +
> [snip]
Jianjun Wang (王建军) Dec. 22, 2020, 3:38 a.m. UTC | #2
On Mon, 2020-12-21 at 10:18 +0800, Nicolas Boichat wrote:
> On Wed, Dec 2, 2020 at 9:39 PM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
> >
> > MediaTek's PCIe host controller has three generation HWs, the new
> > generation HW is an individual bridge, it supports Gen3 speed and
> > up to 256 MSI interrupt numbers for multi-function devices.
> >
> > Add support for new Gen3 controller which can be found on MT8192.
> >
> > Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
> > Acked-by: Ryder Lee <ryder.lee@mediatek.com>
> 
> FWIW, I looked at Rob and Bjorn's comments on v4, and they seem to
> have been addressed (with one small nit highlighted below).
> 
> > ---
> > This patch dependents on "PCI: Export pci_pio_to_address() for module use"[1]
> > to build as a kernel module.
> >
> > This interface will be used by PCI host drivers for PIO translation,
> > export it to support compiling those drivers as kernel modules.
> >
> > [1]http://lists.infradead.org/pipermail/linux-mediatek/2020-December/019504.html
> > ---
> >  drivers/pci/controller/Kconfig              |   13 +
> >  drivers/pci/controller/Makefile             |    1 +
> >  drivers/pci/controller/pcie-mediatek-gen3.c | 1039 +++++++++++++++++++
> >  3 files changed, 1053 insertions(+)
> >  create mode 100644 drivers/pci/controller/pcie-mediatek-gen3.c
> >
> > [snip]
> > diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
> > new file mode 100644
> > index 000000000000..d30ea734ac0a
> > --- /dev/null
> > +++ b/drivers/pci/controller/pcie-mediatek-gen3.c
> > @@ -0,0 +1,1039 @@
> > [snip]
> > +static int mtk_pcie_set_trans_table(struct mtk_pcie_port *port,
> > +                                   resource_size_t cpu_addr,
> > +                                   resource_size_t pci_addr,
> > +                                   resource_size_t size,
> > +                                   unsigned long type, int num)
> > +{
> > +       void __iomem *table;
> > +       u32 val = 0;
> 
> You don't need to init val to 0.
> 
> > +
> > +       if (num >= PCIE_MAX_TRANS_TABLES) {
> > +               dev_notice(port->dev, "not enough translate table[%d] for addr: %#llx, limited to [%d]\n",
> > +                          num, (unsigned long long) cpu_addr,
> > +                          PCIE_MAX_TRANS_TABLES);
> > +               return -ENODEV;
> > +       }
> > +
> > +       table = port->base + PCIE_TRANS_TABLE_BASE_REG +
> > +               num * PCIE_ATR_TLB_SET_OFFSET;
> > +
> > +       writel(lower_32_bits(cpu_addr) | PCIE_ATR_SIZE(fls(size) - 1), table);
> > +       writel(upper_32_bits(cpu_addr), table + PCIE_ATR_SRC_ADDR_MSB_OFFSET);
> > +       writel(lower_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_LSB_OFFSET);
> > +       writel(upper_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_MSB_OFFSET);
> > +
> > +       if (type == IORESOURCE_IO)
> > +               val = PCIE_ATR_TYPE_IO | PCIE_ATR_TLP_TYPE_IO;
> > +       else
> > +               val = PCIE_ATR_TYPE_MEM | PCIE_ATR_TLP_TYPE_MEM;
> > +
> > +       writel(val, table + PCIE_ATR_TRSL_PARAM_OFFSET);
> > +
> > +       return 0;
> > +}
> > +
> > +static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
> > +{
> > +       struct resource_entry *entry;
> > +       struct pci_host_bridge *host = pci_host_bridge_from_priv(port);
> > +       unsigned int table_index = 0;
> > +       int err;
> > +       u32 val;
> > +
> > +       /* Set as RC mode */
> > +       val = readl(port->base + PCIE_SETTING_REG);
> > +       val |= PCIE_RC_MODE;
> > +       writel(val, port->base + PCIE_SETTING_REG);
> > +
> > +       /* Set class code */
> > +       val = readl(port->base + PCIE_PCI_IDS_1);
> > +       val &= ~GENMASK(31, 8);
> > +       val |= PCI_CLASS(PCI_CLASS_BRIDGE_PCI << 8);
> > +       writel(val, port->base + PCIE_PCI_IDS_1);
> > +
> > +       /* Assert all reset signals */
> > +       val = readl(port->base + PCIE_RST_CTRL_REG);
> > +       val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB;
> > +       writel(val, port->base + PCIE_RST_CTRL_REG);
> > +
> > +       /* De-assert reset signals */
> > +       val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB);
> > +       writel(val, port->base + PCIE_RST_CTRL_REG);
> > +
> > +       /* Delay 100ms to wait the reference clocks become stable */
> > +       usleep_range(100 * 1000, 120 * 1000);
> 
> Any reason not to use msleep(100)?

No special reasons, but it seems the msleep() should be used when the
sleep time is more than 20ms (base on
Documentation/timers/timers-howto.rst).

I will replace to msleep(100) in the next version, thanks for your
review.
> 
> > +
> > +       /* De-assert PERST# signal */
> > +       val &= ~PCIE_PE_RSTB;
> > +       writel(val, port->base + PCIE_RST_CTRL_REG);
> > +
> > +       /* Check if the link is up or not */
> > +       err = readl_poll_timeout(port->base + PCIE_LINK_STATUS_REG, val,
> > +                       !!(val & PCIE_PORT_LINKUP), 20,
> > +                       50 * USEC_PER_MSEC);
> > +       if (err) {
> > +               val = readl(port->base + PCIE_LTSSM_STATUS_REG);
> > +               dev_notice(port->dev, "PCIe link down, ltssm reg val: %#x\n",
> > +                          val);
> > +               return err;
> > +       }
> > +
> > +       /* Set PCIe translation windows */
> > +       resource_list_for_each_entry(entry, &host->windows) {
> > +               struct resource *res = entry->res;
> > +               unsigned long type = resource_type(res);
> > +               resource_size_t cpu_addr;
> > +               resource_size_t pci_addr;
> > +               resource_size_t size;
> > +               const char *range_type;
> > +
> > +               if (type == IORESOURCE_IO) {
> > +                       cpu_addr = pci_pio_to_address(res->start);
> > +                       range_type = "IO";
> > +               } else if (type == IORESOURCE_MEM) {
> > +                       cpu_addr = res->start;
> > +                       range_type = "MEM";
> > +               } else {
> > +                       continue;
> > +               }
> > +
> > +               pci_addr = res->start - entry->offset;
> > +               size = resource_size(res);
> > +               err = mtk_pcie_set_trans_table(port, cpu_addr, pci_addr, size,
> > +                                              type, table_index);
> > +               if (err)
> > +                       return err;
> > +
> > +               dev_dbg(port->dev, "set %s trans window[%d]: cpu_addr = %#llx, pci_addr = %#llx, size = %#llx\n",
> > +                       range_type, table_index, (unsigned long long) cpu_addr,
> > +                       (unsigned long long) pci_addr,
> > +                       (unsigned long long) size);
> > +
> > +               table_index++;
> > +       }
> > +
> > +       return 0;
> > +}
> > +
> > [snip]
> > +static irq_hw_number_t mtk_pcie_msi_get_hwirq(struct msi_domain_info *info,
> > +                                             msi_alloc_info_t *arg)
> > +{
> > +       struct msi_desc *entry = arg->desc;
> > +       struct mtk_pcie_port *port = info->chip_data;
> > +       int hwirq;
> > +
> > +       mutex_lock(&port->lock);
> > +
> > +       hwirq = bitmap_find_free_region(port->msi_irq_in_use, PCIE_MSI_IRQS_NUM,
> > +                                       order_base_2(entry->nvec_used));
> > +       if (hwirq < 0) {
> > +               mutex_unlock(&port->lock);
> > +               return -ENOSPC;
> > +       }
> > +
> > +       mutex_unlock(&port->lock);
> > +
> > +       return hwirq;
> 
> Code is good, but I had to look twice to make sure the mutex is
> unlocked. Is the following marginally better?
> 
> hwirq = ...;
> 
> mutex_unlock(&port->lock);
> 
> if (hwirq < 0)
>    return -ENOSPC;
> 
> return hwirq;

Impressive, I will fix it in the next version, and I think the hwirq can
be returned directly since it will be a negative value if
bitmap_find_free_region is failed. The code will be like the following:

hwirq = ...;

mutex_unlock(&port->lock);

return hwirq;

> 
> > +}
> > +
> > [snip]
> > +static void mtk_pcie_msi_handler(struct irq_desc *desc)
> > +{
> > +       struct mtk_pcie_msi *msi_info = irq_desc_get_handler_data(desc);
> > +       struct irq_chip *irqchip = irq_desc_get_chip(desc);
> > +       unsigned long msi_enable, msi_status;
> > +       unsigned int virq;
> > +       irq_hw_number_t bit, hwirq;
> > +
> > +       chained_irq_enter(irqchip, desc);
> > +
> > +       msi_enable = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
> > +       while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET))) {
> > +               msi_status &= msi_enable;
> 
> I don't know much about MSI, but what happens if you have a bit that
> is set in PCIE_MSI_STATUS_OFFSET register, but not in msi_enable?

If the bit that in PCIE_MSI_STATUS_OFFSET register is set but not in
msi_enable, it must be an abnormal usage of MSI or something goes wrong,
it should be ignored in case we can not find the corresponding handler.

> Sounds like you'll just spin-loop forever without acknowledging the
> interrupt.

The interrupt will be acknowledged in the irq_ack callback of
mtk_msi_irq_chip, which belongs to the msi_domain.

> 
> > +               for_each_set_bit(bit, &msi_status, PCIE_MSI_IRQS_PER_SET) {
> > +                       hwirq = bit + msi_info->index * PCIE_MSI_IRQS_PER_SET;
> > +                       virq = irq_find_mapping(msi_info->domain, hwirq);
> > +                       generic_handle_irq(virq);
> > +               }
> > +       }
> > +
> > +       chained_irq_exit(irqchip, desc);
> > +}
> > +
> > [snip]
> > +static int __maybe_unused mtk_pcie_suspend_noirq(struct device *dev)
> > +{
> > +       struct mtk_pcie_port *port = dev_get_drvdata(dev);
> > +       int err;
> > +       u32 val;
> > +
> > +       /* Trigger link to L2 state */
> > +       err = mtk_pcie_turn_off_link(port);
> > +       if (err) {
> > +               dev_notice(port->dev, "can not enter L2 state\n");
> 
> Rob suggested dev_error here.
> 
> (and IMHO, or lot of the other dev_notice above should probably get dev_error)

I will replace to dev_err, thanks for your review.
> 
> > +               return err;
> > +       }
> > +
> > +       /* Pull down the PERST# pin */
> > +       val = readl(port->base + PCIE_RST_CTRL_REG);
> > +       val |= PCIE_PE_RSTB;
> > +       writel(val, port->base + PCIE_RST_CTRL_REG);
> > +
> > +       dev_dbg(port->dev, "enter L2 state success");
> > +
> > +       clk_bulk_disable_unprepare(port->num_clks, port->clks);
> > +
> > +       phy_power_off(port->phy);
> > +
> > +       return 0;
> > +}
> > +
> > [snip]
> 
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
Nicolas Boichat Dec. 22, 2020, 3:55 a.m. UTC | #3
On Tue, Dec 22, 2020 at 11:38 AM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
>
> On Mon, 2020-12-21 at 10:18 +0800, Nicolas Boichat wrote:
> > On Wed, Dec 2, 2020 at 9:39 PM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
> > > [snip]
> > > +static irq_hw_number_t mtk_pcie_msi_get_hwirq(struct msi_domain_info *info,
> > > +                                             msi_alloc_info_t *arg)
> > > +{
> > > +       struct msi_desc *entry = arg->desc;
> > > +       struct mtk_pcie_port *port = info->chip_data;
> > > +       int hwirq;
> > > +
> > > +       mutex_lock(&port->lock);
> > > +
> > > +       hwirq = bitmap_find_free_region(port->msi_irq_in_use, PCIE_MSI_IRQS_NUM,
> > > +                                       order_base_2(entry->nvec_used));
> > > +       if (hwirq < 0) {
> > > +               mutex_unlock(&port->lock);
> > > +               return -ENOSPC;
> > > +       }
> > > +
> > > +       mutex_unlock(&port->lock);
> > > +
> > > +       return hwirq;
> >
> > Code is good, but I had to look twice to make sure the mutex is
> > unlocked. Is the following marginally better?
> >
> > hwirq = ...;
> >
> > mutex_unlock(&port->lock);
> >
> > if (hwirq < 0)
> >    return -ENOSPC;
> >
> > return hwirq;
>
> Impressive, I will fix it in the next version, and I think the hwirq can
> be returned directly since it will be a negative value if
> bitmap_find_free_region is failed. The code will be like the following:
>
> hwirq = ...;
>
> mutex_unlock(&port->lock);
>
> return hwirq;

SG, as long as you're okay with returning -ENOMEM instead of -ENOSPC.

But now I'm having doubt if negative return values are ok, as
irq_hw_number_t is unsigned long.

msi_domain_alloc
(https://elixir.bootlin.com/linux/latest/source/kernel/irq/msi.c#L143)
uses it to call irq_find_mapping
(https://elixir.bootlin.com/linux/latest/source/kernel/irq/irqdomain.c#L882)
without check, and I'm not convinced irq_find_mapping will error out
gracefully...

> >
> > > +}
> > > +
> > > [snip]
> > > +static void mtk_pcie_msi_handler(struct irq_desc *desc)
> > > +{
> > > +       struct mtk_pcie_msi *msi_info = irq_desc_get_handler_data(desc);
> > > +       struct irq_chip *irqchip = irq_desc_get_chip(desc);
> > > +       unsigned long msi_enable, msi_status;
> > > +       unsigned int virq;
> > > +       irq_hw_number_t bit, hwirq;
> > > +
> > > +       chained_irq_enter(irqchip, desc);
> > > +
> > > +       msi_enable = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
> > > +       while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET))) {
> > > +               msi_status &= msi_enable;
> >
> > I don't know much about MSI, but what happens if you have a bit that
> > is set in PCIE_MSI_STATUS_OFFSET register, but not in msi_enable?
>
> If the bit that in PCIE_MSI_STATUS_OFFSET register is set but not in
> msi_enable, it must be an abnormal usage of MSI or something goes wrong,
> it should be ignored in case we can not find the corresponding handler.
>
> > Sounds like you'll just spin-loop forever without acknowledging the
> > interrupt.
>
> The interrupt will be acknowledged in the irq_ack callback of
> mtk_msi_irq_chip, which belongs to the msi_domain.

Let's try to go through it (and please explain to me if I get this wrong).

Say we have:

msi_enable = [PCIE_MSI_ENABLE_OFFSET] = 0x1;

while loop:

msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x3;
msi_status &= msi_enable => msi_status = 0x3 & 0x1 = 0x1;
for_each_set_bit(msi_status) {
   do something that presumably will disable the MSI interrupt status?
}
(next loop iteration)

msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x2;
msi_status &= msi_enable => msi_status = 0x2 & 0x1 = 0x0;
for_each_set_bit(msi_status) => does nothing.

msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x2;
(infinite loop)

Basically, I'm wondering if you should replace the while condition
statement with:

while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET) &
msi_enable))
Jianjun Wang (王建军) Dec. 22, 2020, 8:38 a.m. UTC | #4
On Tue, 2020-12-22 at 11:55 +0800, Nicolas Boichat wrote:
> On Tue, Dec 22, 2020 at 11:38 AM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
> >
> > On Mon, 2020-12-21 at 10:18 +0800, Nicolas Boichat wrote:
> > > On Wed, Dec 2, 2020 at 9:39 PM Jianjun Wang <jianjun.wang@mediatek.com> wrote:
> > > > [snip]
> > > > +static irq_hw_number_t mtk_pcie_msi_get_hwirq(struct msi_domain_info *info,
> > > > +                                             msi_alloc_info_t *arg)
> > > > +{
> > > > +       struct msi_desc *entry = arg->desc;
> > > > +       struct mtk_pcie_port *port = info->chip_data;
> > > > +       int hwirq;
> > > > +
> > > > +       mutex_lock(&port->lock);
> > > > +
> > > > +       hwirq = bitmap_find_free_region(port->msi_irq_in_use, PCIE_MSI_IRQS_NUM,
> > > > +                                       order_base_2(entry->nvec_used));
> > > > +       if (hwirq < 0) {
> > > > +               mutex_unlock(&port->lock);
> > > > +               return -ENOSPC;
> > > > +       }
> > > > +
> > > > +       mutex_unlock(&port->lock);
> > > > +
> > > > +       return hwirq;
> > >
> > > Code is good, but I had to look twice to make sure the mutex is
> > > unlocked. Is the following marginally better?
> > >
> > > hwirq = ...;
> > >
> > > mutex_unlock(&port->lock);
> > >
> > > if (hwirq < 0)
> > >    return -ENOSPC;
> > >
> > > return hwirq;
> >
> > Impressive, I will fix it in the next version, and I think the hwirq can
> > be returned directly since it will be a negative value if
> > bitmap_find_free_region is failed. The code will be like the following:
> >
> > hwirq = ...;
> >
> > mutex_unlock(&port->lock);
> >
> > return hwirq;
> 
> SG, as long as you're okay with returning -ENOMEM instead of -ENOSPC.
> 
> But now I'm having doubt if negative return values are ok, as
> irq_hw_number_t is unsigned long.
> 
> msi_domain_alloc
> (https://elixir.bootlin.com/linux/latest/source/kernel/irq/msi.c#L143)
> uses it to call irq_find_mapping
> (https://elixir.bootlin.com/linux/latest/source/kernel/irq/irqdomain.c#L882)
> without check, and I'm not convinced irq_find_mapping will error out
> gracefully...
> 
I see, it seems the msi_domain_alloc function assume the get_hwirq
callback always success, maybe I should allocate the real hwirq in the
msi_prepare
(https://elixir.bootlin.com/linux/latest/source/kernel/irq/msi.c#L304)
and set it to arg->hwirq, and override the set_desc
(https://elixir.bootlin.com/linux/latest/source/drivers/pci/msi.c#L1405)
to prevent the modify of arg->hwirq.

> > >
> > > > +}
> > > > +
> > > > [snip]
> > > > +static void mtk_pcie_msi_handler(struct irq_desc *desc)
> > > > +{
> > > > +       struct mtk_pcie_msi *msi_info = irq_desc_get_handler_data(desc);
> > > > +       struct irq_chip *irqchip = irq_desc_get_chip(desc);
> > > > +       unsigned long msi_enable, msi_status;
> > > > +       unsigned int virq;
> > > > +       irq_hw_number_t bit, hwirq;
> > > > +
> > > > +       chained_irq_enter(irqchip, desc);
> > > > +
> > > > +       msi_enable = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
> > > > +       while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET))) {
> > > > +               msi_status &= msi_enable;
> > >
> > > I don't know much about MSI, but what happens if you have a bit that
> > > is set in PCIE_MSI_STATUS_OFFSET register, but not in msi_enable?
> >
> > If the bit that in PCIE_MSI_STATUS_OFFSET register is set but not in
> > msi_enable, it must be an abnormal usage of MSI or something goes wrong,
> > it should be ignored in case we can not find the corresponding handler.
> >
> > > Sounds like you'll just spin-loop forever without acknowledging the
> > > interrupt.
> >
> > The interrupt will be acknowledged in the irq_ack callback of
> > mtk_msi_irq_chip, which belongs to the msi_domain.
> 
> Let's try to go through it (and please explain to me if I get this wrong).
> 
> Say we have:
> 
> msi_enable = [PCIE_MSI_ENABLE_OFFSET] = 0x1;
> 
> while loop:
> 
> msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x3;
> msi_status &= msi_enable => msi_status = 0x3 & 0x1 = 0x1;
> for_each_set_bit(msi_status) {
>    do something that presumably will disable the MSI interrupt status?

Yes, the corresponding interrupt status will be cleared.

> }
> (next loop iteration)
> 
> msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x2;
> msi_status &= msi_enable => msi_status = 0x2 & 0x1 = 0x0;
> for_each_set_bit(msi_status) => does nothing.
> 
> msi_status = [PCIE_MSI_STATUS_OFFSET] = 0x2;
> (infinite loop)
> 
> Basically, I'm wondering if you should replace the while condition
> statement with:
> 
> while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET) &
> msi_enable))
> 

Yes, it will be a dead loop if we receive an abnormal interrupt status,
I will fix it in the next version, thanks for your kindly review.

> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
diff mbox series

Patch

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index f18c3725ef80..519461642193 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -239,6 +239,19 @@  config PCIE_MEDIATEK
 	  Say Y here if you want to enable PCIe controller support on
 	  MediaTek SoCs.
 
+config PCIE_MEDIATEK_GEN3
+	tristate "MediaTek Gen3 PCIe controller"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on PCI_MSI_IRQ_DOMAIN
+	help
+	  Adds support for PCIe Gen3 MAC controller for MediaTek SoCs.
+	  This PCIe controller is compatible with Gen3, Gen2 and Gen1 speed,
+	  and support up to 256 MSI interrupt numbers for
+	  multi-function devices.
+
+	  Say Y here if you want to enable Gen3 PCIe controller support on
+	  MediaTek SoCs.
+
 config PCIE_TANGO_SMP8759
 	bool "Tango SMP8759 PCIe controller (DANGEROUS)"
 	depends on ARCH_TANGO && PCI_MSI && OF
diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile
index bcdbf49ab1e4..9c1b96777597 100644
--- a/drivers/pci/controller/Makefile
+++ b/drivers/pci/controller/Makefile
@@ -27,6 +27,7 @@  obj-$(CONFIG_PCIE_ROCKCHIP) += pcie-rockchip.o
 obj-$(CONFIG_PCIE_ROCKCHIP_EP) += pcie-rockchip-ep.o
 obj-$(CONFIG_PCIE_ROCKCHIP_HOST) += pcie-rockchip-host.o
 obj-$(CONFIG_PCIE_MEDIATEK) += pcie-mediatek.o
+obj-$(CONFIG_PCIE_MEDIATEK_GEN3) += pcie-mediatek-gen3.o
 obj-$(CONFIG_PCIE_TANGO_SMP8759) += pcie-tango.o
 obj-$(CONFIG_VMD) += vmd.o
 obj-$(CONFIG_PCIE_BRCMSTB) += pcie-brcmstb.o
diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
new file mode 100644
index 000000000000..d30ea734ac0a
--- /dev/null
+++ b/drivers/pci/controller/pcie-mediatek-gen3.c
@@ -0,0 +1,1039 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MediaTek PCIe host controller driver.
+ *
+ * Copyright (c) 2020 MediaTek Inc.
+ * Author: Jianjun Wang <jianjun.wang@mediatek.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_clk.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+
+#include "../pci.h"
+
+#define PCIE_SETTING_REG		0x80
+#define PCIE_PCI_IDS_1			0x9c
+#define PCI_CLASS(class)		(class << 8)
+#define PCIE_RC_MODE			BIT(0)
+
+#define PCIE_CFGNUM_REG			0x140
+#define PCIE_CFG_DEVFN(devfn)		((devfn) & GENMASK(7, 0))
+#define PCIE_CFG_BUS(bus)		(((bus) << 8) & GENMASK(15, 8))
+#define PCIE_CFG_BYTE_EN(bytes)		(((bytes) << 16) & GENMASK(19, 16))
+#define PCIE_CFG_FORCE_BYTE_EN		BIT(20)
+#define PCIE_CFG_OFFSET_ADDR		0x1000
+#define PCIE_CFG_HEADER(bus, devfn) \
+	(PCIE_CFG_BUS(bus) | PCIE_CFG_DEVFN(devfn))
+
+#define PCIE_RST_CTRL_REG		0x148
+#define PCIE_MAC_RSTB			BIT(0)
+#define PCIE_PHY_RSTB			BIT(1)
+#define PCIE_BRG_RSTB			BIT(2)
+#define PCIE_PE_RSTB			BIT(3)
+
+#define PCIE_LTSSM_STATUS_REG		0x150
+#define PCIE_LTSSM_STATE_MASK		GENMASK(28, 24)
+#define PCIE_LTSSM_STATE(val)		((val & PCIE_LTSSM_STATE_MASK) >> 24)
+#define PCIE_LTSSM_STATE_L2_IDLE	0x14
+
+#define PCIE_LINK_STATUS_REG		0x154
+#define PCIE_PORT_LINKUP		BIT(8)
+
+#define PCIE_MSI_SET_NUM		8
+#define PCIE_MSI_IRQS_PER_SET		32
+#define PCIE_MSI_IRQS_NUM \
+	(PCIE_MSI_IRQS_PER_SET * (PCIE_MSI_SET_NUM))
+
+#define PCIE_INT_ENABLE_REG		0x180
+#define PCIE_MSI_MASK			GENMASK(PCIE_MSI_SET_NUM + 8 - 1, 8)
+#define PCIE_MSI_SHIFT			8
+#define PCIE_INTX_SHIFT			24
+#define PCIE_INTX_MASK			GENMASK(27, 24)
+
+#define PCIE_INT_STATUS_REG		0x184
+#define PCIE_MSI_SET_ENABLE_REG		0x190
+
+#define PCIE_ICMD_PM_REG		0x198
+#define PCIE_TURN_OFF_LINK		BIT(4)
+
+#define PCIE_MSI_ADDR_BASE_REG		0xc00
+#define PCIE_MSI_SET_OFFSET		0x10
+#define PCIE_MSI_STATUS_OFFSET		0x04
+#define PCIE_MSI_ENABLE_OFFSET		0x08
+
+#define PCIE_TRANS_TABLE_BASE_REG	0x800
+#define PCIE_ATR_SRC_ADDR_MSB_OFFSET	0x4
+#define PCIE_ATR_TRSL_ADDR_LSB_OFFSET	0x8
+#define PCIE_ATR_TRSL_ADDR_MSB_OFFSET	0xc
+#define PCIE_ATR_TRSL_PARAM_OFFSET	0x10
+#define PCIE_ATR_TLB_SET_OFFSET		0x20
+
+#define PCIE_MAX_TRANS_TABLES		8
+#define PCIE_ATR_EN			BIT(0)
+#define PCIE_ATR_SIZE(size) \
+	(((((size) - 1) << 1) & GENMASK(6, 1)) | PCIE_ATR_EN)
+#define PCIE_ATR_ID(id)			((id) & GENMASK(3, 0))
+#define PCIE_ATR_TYPE_MEM		PCIE_ATR_ID(0)
+#define PCIE_ATR_TYPE_IO		PCIE_ATR_ID(1)
+#define PCIE_ATR_TLP_TYPE(type)		(((type) << 16) & GENMASK(18, 16))
+#define PCIE_ATR_TLP_TYPE_MEM		PCIE_ATR_TLP_TYPE(0)
+#define PCIE_ATR_TLP_TYPE_IO		PCIE_ATR_TLP_TYPE(2)
+
+/**
+ * struct mtk_pcie_msi - MSI information for each set
+ * @base: IO mapped register base
+ * @irq: MSI set Interrupt number
+ * @index: MSI set number
+ * @msg_addr: MSI message address
+ * @domain: IRQ domain
+ */
+struct mtk_pcie_msi {
+	void __iomem *base;
+	unsigned int irq;
+	int index;
+	phys_addr_t msg_addr;
+	struct irq_domain *domain;
+};
+
+/**
+ * struct mtk_pcie_port - PCIe port information
+ * @dev: PCIe device
+ * @base: IO mapped register base
+ * @reg_base: Physical register base
+ * @mac_reset: mac reset control
+ * @phy_reset: phy reset control
+ * @phy: PHY controller block
+ * @clks: PCIe clocks
+ * @num_clks: PCIe clocks count for this port
+ * @irq: PCIe controller interrupt number
+ * @intx_domain: legacy INTx IRQ domain
+ * @msi_domain: MSI IRQ domain
+ * @msi_top_domain: MSI IRQ top domain
+ * @msi_info: MSI sets information
+ * @lock: lock protecting IRQ bit map
+ * @msi_irq_in_use: bit map for assigned MSI IRQ
+ */
+struct mtk_pcie_port {
+	struct device *dev;
+	void __iomem *base;
+	phys_addr_t reg_base;
+	struct reset_control *mac_reset;
+	struct reset_control *phy_reset;
+	struct phy *phy;
+	struct clk_bulk_data *clks;
+	int num_clks;
+
+	int irq;
+	struct irq_domain *intx_domain;
+	struct irq_domain *msi_domain;
+	struct irq_domain *msi_top_domain;
+	struct mtk_pcie_msi **msi_info;
+	struct mutex lock;
+	DECLARE_BITMAP(msi_irq_in_use, PCIE_MSI_IRQS_NUM);
+};
+
+/**
+ * mtk_pcie_config_tlp_header
+ * @bus: PCI bus to query
+ * @devfn: device/function number
+ * @where: offset in config space
+ * @size: data size in TLP header
+ *
+ * Set byte enable field and device information in configuration TLP header.
+ */
+static void mtk_pcie_config_tlp_header(struct pci_bus *bus, unsigned int devfn,
+					int where, int size)
+{
+	struct mtk_pcie_port *port = bus->sysdata;
+	int bytes;
+	u32 val;
+
+	bytes = (GENMASK(size - 1, 0) & 0xf) << (where & 0x3);
+
+	val = PCIE_CFG_FORCE_BYTE_EN | PCIE_CFG_BYTE_EN(bytes) |
+	      PCIE_CFG_HEADER(bus->number, devfn);
+
+	writel(val, port->base + PCIE_CFGNUM_REG);
+}
+
+static void __iomem *mtk_pcie_map_bus(struct pci_bus *bus, unsigned int devfn,
+				      int where)
+{
+	struct mtk_pcie_port *port = bus->sysdata;
+
+	return port->base + PCIE_CFG_OFFSET_ADDR + where;
+}
+
+static int mtk_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
+				int where, int size, u32 *val)
+{
+	mtk_pcie_config_tlp_header(bus, devfn, where, size);
+
+	return pci_generic_config_read32(bus, devfn, where, size, val);
+}
+
+static int mtk_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
+				 int where, int size, u32 val)
+{
+	mtk_pcie_config_tlp_header(bus, devfn, where, size);
+
+	if (size <= 2)
+		val <<= (where & 0x3) * 8;
+
+	return pci_generic_config_write32(bus, devfn, where, 4, val);
+}
+
+static struct pci_ops mtk_pcie_ops = {
+	.map_bus = mtk_pcie_map_bus,
+	.read  = mtk_pcie_config_read,
+	.write = mtk_pcie_config_write,
+};
+
+static int mtk_pcie_set_trans_table(struct mtk_pcie_port *port,
+				    resource_size_t cpu_addr,
+				    resource_size_t pci_addr,
+				    resource_size_t size,
+				    unsigned long type, int num)
+{
+	void __iomem *table;
+	u32 val = 0;
+
+	if (num >= PCIE_MAX_TRANS_TABLES) {
+		dev_notice(port->dev, "not enough translate table[%d] for addr: %#llx, limited to [%d]\n",
+			   num, (unsigned long long) cpu_addr,
+			   PCIE_MAX_TRANS_TABLES);
+		return -ENODEV;
+	}
+
+	table = port->base + PCIE_TRANS_TABLE_BASE_REG +
+		num * PCIE_ATR_TLB_SET_OFFSET;
+
+	writel(lower_32_bits(cpu_addr) | PCIE_ATR_SIZE(fls(size) - 1), table);
+	writel(upper_32_bits(cpu_addr), table + PCIE_ATR_SRC_ADDR_MSB_OFFSET);
+	writel(lower_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_LSB_OFFSET);
+	writel(upper_32_bits(pci_addr), table + PCIE_ATR_TRSL_ADDR_MSB_OFFSET);
+
+	if (type == IORESOURCE_IO)
+		val = PCIE_ATR_TYPE_IO | PCIE_ATR_TLP_TYPE_IO;
+	else
+		val = PCIE_ATR_TYPE_MEM | PCIE_ATR_TLP_TYPE_MEM;
+
+	writel(val, table + PCIE_ATR_TRSL_PARAM_OFFSET);
+
+	return 0;
+}
+
+static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
+{
+	struct resource_entry *entry;
+	struct pci_host_bridge *host = pci_host_bridge_from_priv(port);
+	unsigned int table_index = 0;
+	int err;
+	u32 val;
+
+	/* Set as RC mode */
+	val = readl(port->base + PCIE_SETTING_REG);
+	val |= PCIE_RC_MODE;
+	writel(val, port->base + PCIE_SETTING_REG);
+
+	/* Set class code */
+	val = readl(port->base + PCIE_PCI_IDS_1);
+	val &= ~GENMASK(31, 8);
+	val |= PCI_CLASS(PCI_CLASS_BRIDGE_PCI << 8);
+	writel(val, port->base + PCIE_PCI_IDS_1);
+
+	/* Assert all reset signals */
+	val = readl(port->base + PCIE_RST_CTRL_REG);
+	val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB;
+	writel(val, port->base + PCIE_RST_CTRL_REG);
+
+	/* De-assert reset signals */
+	val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB);
+	writel(val, port->base + PCIE_RST_CTRL_REG);
+
+	/* Delay 100ms to wait the reference clocks become stable */
+	usleep_range(100 * 1000, 120 * 1000);
+
+	/* De-assert PERST# signal */
+	val &= ~PCIE_PE_RSTB;
+	writel(val, port->base + PCIE_RST_CTRL_REG);
+
+	/* Check if the link is up or not */
+	err = readl_poll_timeout(port->base + PCIE_LINK_STATUS_REG, val,
+			!!(val & PCIE_PORT_LINKUP), 20,
+			50 * USEC_PER_MSEC);
+	if (err) {
+		val = readl(port->base + PCIE_LTSSM_STATUS_REG);
+		dev_notice(port->dev, "PCIe link down, ltssm reg val: %#x\n",
+			   val);
+		return err;
+	}
+
+	/* Set PCIe translation windows */
+	resource_list_for_each_entry(entry, &host->windows) {
+		struct resource *res = entry->res;
+		unsigned long type = resource_type(res);
+		resource_size_t cpu_addr;
+		resource_size_t pci_addr;
+		resource_size_t size;
+		const char *range_type;
+
+		if (type == IORESOURCE_IO) {
+			cpu_addr = pci_pio_to_address(res->start);
+			range_type = "IO";
+		} else if (type == IORESOURCE_MEM) {
+			cpu_addr = res->start;
+			range_type = "MEM";
+		} else {
+			continue;
+		}
+
+		pci_addr = res->start - entry->offset;
+		size = resource_size(res);
+		err = mtk_pcie_set_trans_table(port, cpu_addr, pci_addr, size,
+					       type, table_index);
+		if (err)
+			return err;
+
+		dev_dbg(port->dev, "set %s trans window[%d]: cpu_addr = %#llx, pci_addr = %#llx, size = %#llx\n",
+			range_type, table_index, (unsigned long long) cpu_addr,
+			(unsigned long long) pci_addr,
+			(unsigned long long) size);
+
+		table_index++;
+	}
+
+	return 0;
+}
+
+static inline struct mtk_pcie_msi *mtk_get_msi_info(struct mtk_pcie_port *port,
+						    unsigned long hwirq)
+{
+	return port->msi_info[hwirq / PCIE_MSI_IRQS_PER_SET];
+}
+
+static int mtk_pcie_set_affinity(struct irq_data *data,
+				 const struct cpumask *mask, bool force)
+{
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	int ret;
+
+	ret = irq_set_affinity_hint(port->irq, mask);
+	if (ret)
+		return ret;
+
+	irq_data_update_effective_affinity(data, mask);
+
+	return 0;
+}
+
+static void mtk_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
+{
+	struct mtk_pcie_msi *msi_info;
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long hwirq;
+
+	msi_info = mtk_get_msi_info(port, data->hwirq);
+	hwirq =	data->hwirq % PCIE_MSI_IRQS_PER_SET;
+
+	msg->address_hi = 0;
+	msg->address_lo = lower_32_bits(msi_info->msg_addr);
+	msg->data = hwirq;
+	dev_dbg(port->dev, "msi#%#lx address_hi %#x address_lo %#x data %d\n",
+		hwirq, msg->address_hi, msg->address_lo, msg->data);
+}
+
+static void mtk_msi_irq_ack(struct irq_data *data)
+{
+	struct mtk_pcie_msi *msi_info;
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long hwirq;
+
+	msi_info = mtk_get_msi_info(port, data->hwirq);
+	hwirq =	data->hwirq % PCIE_MSI_IRQS_PER_SET;
+
+	writel(BIT(hwirq), msi_info->base + PCIE_MSI_STATUS_OFFSET);
+}
+
+static void mtk_msi_irq_mask(struct irq_data *data)
+{
+	struct mtk_pcie_msi *msi_info;
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long hwirq;
+	u32 val;
+
+	msi_info = mtk_get_msi_info(port, data->hwirq);
+	hwirq =	data->hwirq % PCIE_MSI_IRQS_PER_SET;
+
+	val = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
+	val &= ~BIT(hwirq);
+	writel(val, msi_info->base + PCIE_MSI_ENABLE_OFFSET);
+
+	pci_msi_mask_irq(data);
+}
+
+static void mtk_msi_irq_unmask(struct irq_data *data)
+{
+	struct mtk_pcie_msi *msi_info;
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long hwirq;
+	u32 val;
+
+	msi_info = mtk_get_msi_info(port, data->hwirq);
+	hwirq =	data->hwirq % PCIE_MSI_IRQS_PER_SET;
+
+	val = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
+	val |= BIT(hwirq);
+	writel(val, msi_info->base + PCIE_MSI_ENABLE_OFFSET);
+
+	pci_msi_unmask_irq(data);
+}
+
+static struct irq_chip mtk_msi_irq_chip = {
+	.irq_ack		= mtk_msi_irq_ack,
+	.irq_compose_msi_msg	= mtk_compose_msi_msg,
+	.irq_mask		= mtk_msi_irq_mask,
+	.irq_unmask		= mtk_msi_irq_unmask,
+	.irq_set_affinity	= mtk_pcie_set_affinity,
+	.name			= "PCIe",
+};
+
+static irq_hw_number_t mtk_pcie_msi_get_hwirq(struct msi_domain_info *info,
+					      msi_alloc_info_t *arg)
+{
+	struct msi_desc *entry = arg->desc;
+	struct mtk_pcie_port *port = info->chip_data;
+	int hwirq;
+
+	mutex_lock(&port->lock);
+
+	hwirq = bitmap_find_free_region(port->msi_irq_in_use, PCIE_MSI_IRQS_NUM,
+					order_base_2(entry->nvec_used));
+	if (hwirq < 0) {
+		mutex_unlock(&port->lock);
+		return -ENOSPC;
+	}
+
+	mutex_unlock(&port->lock);
+
+	return hwirq;
+}
+
+static void mtk_pcie_msi_free(struct irq_domain *domain,
+			      struct msi_domain_info *info, unsigned int virq)
+{
+	struct irq_data *data = irq_domain_get_irq_data(domain, virq);
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+
+	mutex_lock(&port->lock);
+
+	bitmap_clear(port->msi_irq_in_use, data->hwirq, 1);
+
+	mutex_unlock(&port->lock);
+}
+
+static struct msi_domain_ops mtk_msi_domain_ops = {
+	.get_hwirq	= mtk_pcie_msi_get_hwirq,
+	.msi_free	= mtk_pcie_msi_free,
+};
+
+static struct msi_domain_info mtk_msi_domain_info = {
+	.flags		= (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_PCI_MSIX |
+			   MSI_FLAG_USE_DEF_CHIP_OPS | MSI_FLAG_MULTI_PCI_MSI),
+	.chip		= &mtk_msi_irq_chip,
+	.ops		= &mtk_msi_domain_ops,
+	.handler	= handle_edge_irq,
+	.handler_name	= "MSI",
+};
+
+static void mtk_msi_top_irq_eoi(struct irq_data *data)
+{
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long msi_irq = data->hwirq + PCIE_MSI_SHIFT;
+
+	writel(BIT(msi_irq), port->base + PCIE_INT_STATUS_REG);
+}
+
+static struct irq_chip mtk_msi_top_irq_chip = {
+	.irq_eoi	= mtk_msi_top_irq_eoi,
+	.name		= "PCIe",
+};
+
+static void mtk_pcie_msi_handler(struct irq_desc *desc)
+{
+	struct mtk_pcie_msi *msi_info = irq_desc_get_handler_data(desc);
+	struct irq_chip *irqchip = irq_desc_get_chip(desc);
+	unsigned long msi_enable, msi_status;
+	unsigned int virq;
+	irq_hw_number_t bit, hwirq;
+
+	chained_irq_enter(irqchip, desc);
+
+	msi_enable = readl(msi_info->base + PCIE_MSI_ENABLE_OFFSET);
+	while ((msi_status = readl(msi_info->base + PCIE_MSI_STATUS_OFFSET))) {
+		msi_status &= msi_enable;
+		for_each_set_bit(bit, &msi_status, PCIE_MSI_IRQS_PER_SET) {
+			hwirq = bit + msi_info->index * PCIE_MSI_IRQS_PER_SET;
+			virq = irq_find_mapping(msi_info->domain, hwirq);
+			generic_handle_irq(virq);
+		}
+	}
+
+	chained_irq_exit(irqchip, desc);
+}
+
+static int mtk_msi_top_domain_map(struct irq_domain *domain,
+				    unsigned int virq, irq_hw_number_t hwirq)
+{
+	struct mtk_pcie_port *port = domain->host_data;
+	struct mtk_pcie_msi *msi_info = port->msi_info[hwirq];
+
+	irq_domain_set_info(domain, virq, hwirq,
+			    &mtk_msi_top_irq_chip, domain->host_data,
+			    mtk_pcie_msi_handler, msi_info, NULL);
+
+	return 0;
+}
+
+static const struct irq_domain_ops mtk_msi_top_domain_ops = {
+	.map = mtk_msi_top_domain_map,
+};
+
+static void mtk_intx_mask(struct irq_data *data)
+{
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	u32 val;
+
+	val = readl(port->base + PCIE_INT_ENABLE_REG);
+	val &= ~BIT(data->hwirq + PCIE_INTX_SHIFT);
+	writel(val, port->base + PCIE_INT_ENABLE_REG);
+}
+
+static void mtk_intx_unmask(struct irq_data *data)
+{
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	u32 val;
+
+	val = readl(port->base + PCIE_INT_ENABLE_REG);
+	val |= BIT(data->hwirq + PCIE_INTX_SHIFT);
+	writel(val, port->base + PCIE_INT_ENABLE_REG);
+}
+
+static void mtk_intx_eoi(struct irq_data *data)
+{
+	struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
+	unsigned long hwirq;
+
+	/**
+	 * As an emulated level IRQ, its interrupt status will remain
+	 * until the corresponding de-assert message is received; hence that
+	 * the status can only be cleared when the interrupt has been serviced.
+	 */
+	hwirq = data->hwirq + PCIE_INTX_SHIFT;
+	writel(BIT(hwirq), port->base + PCIE_INT_STATUS_REG);
+}
+
+static struct irq_chip mtk_intx_irq_chip = {
+	.irq_mask		= mtk_intx_mask,
+	.irq_unmask		= mtk_intx_unmask,
+	.irq_eoi		= mtk_intx_eoi,
+	.irq_set_affinity	= mtk_pcie_set_affinity,
+	.name			= "PCIe",
+};
+
+static int mtk_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+			     irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler_name(irq, &mtk_intx_irq_chip,
+				      handle_fasteoi_irq, "INTx");
+	irq_set_chip_data(irq, domain->host_data);
+
+	return 0;
+}
+
+static const struct irq_domain_ops intx_domain_ops = {
+	.map = mtk_pcie_intx_map,
+};
+
+static int mtk_pcie_init_irq_domains(struct mtk_pcie_port *port,
+				     struct device_node *node)
+{
+	struct device *dev = port->dev;
+	struct device_node *intc_node;
+	struct fwnode_handle *fwnode = of_node_to_fwnode(node);
+	struct mtk_pcie_msi *msi_info;
+	struct msi_domain_info *info;
+	int i, ret;
+
+	/* Setup INTx */
+	intc_node = of_get_child_by_name(node, "interrupt-controller");
+	if (!intc_node) {
+		dev_notice(dev, "missing PCIe Intc node\n");
+		return -ENODEV;
+	}
+
+	port->intx_domain = irq_domain_add_linear(intc_node, PCI_NUM_INTX,
+						  &intx_domain_ops, port);
+	if (!port->intx_domain) {
+		dev_notice(dev, "failed to get INTx IRQ domain\n");
+		return -ENODEV;
+	}
+
+	/* Setup MSI */
+	mutex_init(&port->lock);
+
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	memcpy(info, &mtk_msi_domain_info, sizeof(*info));
+	info->chip_data = port;
+
+	port->msi_domain = pci_msi_create_irq_domain(fwnode, info, NULL);
+	if (!port->msi_domain) {
+		dev_info(dev, "failed to create MSI domain\n");
+		ret = -ENODEV;
+		goto err_msi_domain;
+	}
+
+	/* Enable MSI and setup PCIe domains */
+	port->msi_top_domain = irq_domain_add_hierarchy(NULL, 0, 0, node,
+							&mtk_msi_top_domain_ops,
+							port);
+	if (!port->msi_top_domain) {
+		dev_info(dev, "failed to create MSI top domain\n");
+		ret = -ENODEV;
+		goto err_msi_top_domain;
+	}
+
+	port->msi_info = devm_kzalloc(dev, PCIE_MSI_SET_NUM, GFP_KERNEL);
+	if (!port->msi_info) {
+		ret = -ENOMEM;
+		goto err_msi_info;
+	}
+
+	for (i = 0; i < PCIE_MSI_SET_NUM; i++) {
+		int offset = i * PCIE_MSI_SET_OFFSET;
+		u32 val;
+
+		msi_info = devm_kzalloc(dev, sizeof(*msi_info), GFP_KERNEL);
+		if (!msi_info) {
+			ret = -ENOMEM;
+			goto err_msi_set;
+		}
+
+		msi_info->base = port->base + PCIE_MSI_ADDR_BASE_REG + offset;
+		msi_info->msg_addr = port->reg_base + PCIE_MSI_ADDR_BASE_REG +
+				     offset;
+
+		writel(lower_32_bits(msi_info->msg_addr), msi_info->base);
+
+		msi_info->index = i;
+		msi_info->domain = port->msi_domain;
+
+		port->msi_info[i] = msi_info;
+
+		/* Alloc IRQ for each MSI set */
+		msi_info->irq = irq_create_mapping(port->msi_top_domain, i);
+		if (!msi_info->irq) {
+			dev_info(dev, "allocate MSI top IRQ failed\n");
+			ret = -ENOSPC;
+			goto err_msi_set;
+		}
+
+		val = readl(port->base + PCIE_INT_ENABLE_REG);
+		val |= BIT(i + PCIE_MSI_SHIFT);
+		writel(val, port->base + PCIE_INT_ENABLE_REG);
+
+		val = readl(port->base + PCIE_MSI_SET_ENABLE_REG);
+		val |= BIT(i);
+		writel(val, port->base + PCIE_MSI_SET_ENABLE_REG);
+	}
+
+	return 0;
+
+err_msi_set:
+	while (i-- > 0) {
+		msi_info = port->msi_info[i];
+		irq_dispose_mapping(msi_info->irq);
+	}
+err_msi_info:
+	irq_domain_remove(port->msi_top_domain);
+err_msi_top_domain:
+	irq_domain_remove(port->msi_domain);
+err_msi_domain:
+	irq_domain_remove(port->intx_domain);
+
+	return ret;
+}
+
+static void mtk_pcie_irq_teardown(struct mtk_pcie_port *port)
+{
+	struct mtk_pcie_msi *msi_info;
+	int i;
+
+	irq_set_chained_handler_and_data(port->irq, NULL, NULL);
+
+	if (port->intx_domain)
+		irq_domain_remove(port->intx_domain);
+
+	if (port->msi_domain)
+		irq_domain_remove(port->msi_domain);
+
+	if (port->msi_top_domain) {
+		for (i = 0; i < PCIE_MSI_SET_NUM; i++) {
+			msi_info = port->msi_info[i];
+			irq_dispose_mapping(msi_info->irq);
+		}
+
+		irq_domain_remove(port->msi_top_domain);
+	}
+
+	irq_dispose_mapping(port->irq);
+}
+
+static void mtk_pcie_irq_handler(struct irq_desc *desc)
+{
+	struct mtk_pcie_port *port = irq_desc_get_handler_data(desc);
+	struct irq_chip *irqchip = irq_desc_get_chip(desc);
+	unsigned long status;
+	unsigned int virq;
+	irq_hw_number_t irq_bit = PCIE_INTX_SHIFT;
+
+	chained_irq_enter(irqchip, desc);
+
+	status = readl(port->base + PCIE_INT_STATUS_REG);
+	if (status & PCIE_INTX_MASK) {
+		for_each_set_bit_from(irq_bit, &status, PCI_NUM_INTX +
+				      PCIE_INTX_SHIFT) {
+			virq = irq_find_mapping(port->intx_domain,
+						irq_bit - PCIE_INTX_SHIFT);
+			generic_handle_irq(virq);
+		}
+	}
+
+	if (status & PCIE_MSI_MASK) {
+		irq_bit = PCIE_MSI_SHIFT;
+		for_each_set_bit_from(irq_bit, &status, PCIE_MSI_SET_NUM +
+				      PCIE_MSI_SHIFT) {
+			virq = irq_find_mapping(port->msi_top_domain,
+						irq_bit - PCIE_MSI_SHIFT);
+			generic_handle_irq(virq);
+		}
+	}
+
+	chained_irq_exit(irqchip, desc);
+}
+
+static int mtk_pcie_setup_irq(struct mtk_pcie_port *port,
+			      struct device_node *node)
+{
+	struct device *dev = port->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	int err;
+
+	err = mtk_pcie_init_irq_domains(port, node);
+	if (err) {
+		dev_notice(dev, "failed to init PCIe IRQ domain\n");
+		return err;
+	}
+
+	port->irq = platform_get_irq(pdev, 0);
+	if (port->irq < 0)
+		return port->irq;
+
+	irq_set_chained_handler_and_data(port->irq, mtk_pcie_irq_handler, port);
+
+	return 0;
+}
+
+static int mtk_pcie_clk_init(struct mtk_pcie_port *port)
+{
+	int ret;
+
+	port->num_clks = devm_clk_bulk_get_all(port->dev, &port->clks);
+	if (port->num_clks < 0) {
+		dev_notice(port->dev, "failed to get PCIe clock\n");
+		return port->num_clks;
+	}
+
+	ret = clk_bulk_prepare_enable(port->num_clks, port->clks);
+	if (ret) {
+		dev_notice(port->dev, "failed to enable PCIe clocks\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int mtk_pcie_power_up(struct mtk_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	int err;
+
+	port->phy_reset = devm_reset_control_get_optional_exclusive(dev, "phy");
+	if (IS_ERR(port->phy_reset))
+		return PTR_ERR(port->phy_reset);
+
+	/* PHY power on and enable pipe clock */
+	port->phy = devm_phy_optional_get(dev, "pcie-phy");
+	if (IS_ERR(port->phy))
+		return PTR_ERR(port->phy);
+
+	reset_control_deassert(port->phy_reset);
+
+	err = phy_power_on(port->phy);
+	if (err) {
+		dev_notice(dev, "failed to power on PCIe phy\n");
+		goto err_phy_on;
+	}
+
+	err = phy_init(port->phy);
+	if (err) {
+		dev_notice(dev, "failed to initialize PCIe phy\n");
+		goto err_phy_init;
+	}
+
+	port->mac_reset = devm_reset_control_get_optional_exclusive(dev, "mac");
+	if (IS_ERR(port->mac_reset)) {
+		err = PTR_ERR(port->mac_reset);
+		goto err_mac_rst;
+	}
+
+	reset_control_deassert(port->mac_reset);
+
+	/* MAC power on and enable transaction layer clocks */
+	pm_runtime_enable(dev);
+	pm_runtime_get_sync(dev);
+
+	err = mtk_pcie_clk_init(port);
+	if (err) {
+		dev_notice(dev, "clock init failed\n");
+		goto err_clk_init;
+	}
+
+	return 0;
+
+err_clk_init:
+	pm_runtime_put_sync(dev);
+	pm_runtime_disable(dev);
+	reset_control_assert(port->mac_reset);
+err_mac_rst:
+	phy_exit(port->phy);
+err_phy_init:
+	phy_power_off(port->phy);
+err_phy_on:
+	reset_control_assert(port->phy_reset);
+
+	return err;
+}
+
+static void mtk_pcie_power_down(struct mtk_pcie_port *port)
+{
+	clk_bulk_disable_unprepare(port->num_clks, port->clks);
+
+	pm_runtime_put_sync(port->dev);
+	pm_runtime_disable(port->dev);
+	reset_control_assert(port->mac_reset);
+
+	phy_power_off(port->phy);
+	phy_exit(port->phy);
+	reset_control_assert(port->phy_reset);
+}
+
+static int mtk_pcie_setup(struct mtk_pcie_port *port)
+{
+	struct device *dev = port->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct resource *regs;
+	int err;
+
+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcie-mac");
+	port->base = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(port->base)) {
+		dev_notice(dev, "failed to map register base\n");
+		return PTR_ERR(port->base);
+	}
+
+	port->reg_base = regs->start;
+
+	/* Don't touch the hardware registers before power up */
+	err = mtk_pcie_power_up(port);
+	if (err)
+		return err;
+
+	/* Try link up */
+	err = mtk_pcie_startup_port(port);
+	if (err) {
+		dev_notice(dev, "PCIe startup failed\n");
+		goto err_setup;
+	}
+
+	err = mtk_pcie_setup_irq(port, dev->of_node);
+	if (err)
+		goto err_setup;
+
+	dev_info(dev, "PCIe link up success!\n");
+
+	return 0;
+
+err_setup:
+	mtk_pcie_power_down(port);
+
+	return err;
+}
+
+static int mtk_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_pcie_port *port;
+	struct pci_host_bridge *host;
+	int err;
+
+	host = devm_pci_alloc_host_bridge(dev, sizeof(*port));
+	if (!host)
+		return -ENOMEM;
+
+	port = pci_host_bridge_priv(host);
+
+	port->dev = dev;
+	platform_set_drvdata(pdev, port);
+
+	err = mtk_pcie_setup(port);
+	if (err)
+		return err;
+
+	host->ops = &mtk_pcie_ops;
+	host->sysdata = port;
+
+	err = pci_host_probe(host);
+	if (err) {
+		mtk_pcie_irq_teardown(port);
+		mtk_pcie_power_down(port);
+		return err;
+	}
+
+	return 0;
+}
+
+static int mtk_pcie_remove(struct platform_device *pdev)
+{
+	struct mtk_pcie_port *port = platform_get_drvdata(pdev);
+	struct pci_host_bridge *host = pci_host_bridge_from_priv(port);
+
+	pci_lock_rescan_remove();
+	pci_stop_root_bus(host->bus);
+	pci_remove_root_bus(host->bus);
+	pci_unlock_rescan_remove();
+
+	mtk_pcie_irq_teardown(port);
+	mtk_pcie_power_down(port);
+
+	return 0;
+}
+
+static int __maybe_unused mtk_pcie_turn_off_link(struct mtk_pcie_port *port)
+{
+	u32 val;
+
+	val = readl(port->base + PCIE_ICMD_PM_REG);
+	val |= PCIE_TURN_OFF_LINK;
+	writel(val, port->base + PCIE_ICMD_PM_REG);
+
+	/* Check the link is L2 */
+	return readl_poll_timeout(port->base + PCIE_LTSSM_STATUS_REG, val,
+				  (PCIE_LTSSM_STATE(val) ==
+				   PCIE_LTSSM_STATE_L2_IDLE), 20,
+				   50 * USEC_PER_MSEC);
+}
+
+static int __maybe_unused mtk_pcie_suspend_noirq(struct device *dev)
+{
+	struct mtk_pcie_port *port = dev_get_drvdata(dev);
+	int err;
+	u32 val;
+
+	/* Trigger link to L2 state */
+	err = mtk_pcie_turn_off_link(port);
+	if (err) {
+		dev_notice(port->dev, "can not enter L2 state\n");
+		return err;
+	}
+
+	/* Pull down the PERST# pin */
+	val = readl(port->base + PCIE_RST_CTRL_REG);
+	val |= PCIE_PE_RSTB;
+	writel(val, port->base + PCIE_RST_CTRL_REG);
+
+	dev_dbg(port->dev, "enter L2 state success");
+
+	clk_bulk_disable_unprepare(port->num_clks, port->clks);
+
+	phy_power_off(port->phy);
+
+	return 0;
+}
+
+static int __maybe_unused mtk_pcie_resume_noirq(struct device *dev)
+{
+	struct mtk_pcie_port *port = dev_get_drvdata(dev);
+	int err;
+
+	phy_power_on(port->phy);
+
+	err = clk_bulk_prepare_enable(port->num_clks, port->clks);
+	if (err) {
+		dev_dbg(dev, "failed to enable PCIe clocks\n");
+		return err;
+	}
+
+	err = mtk_pcie_startup_port(port);
+	if (err) {
+		dev_notice(port->dev, "resume failed\n");
+		return err;
+	}
+
+	dev_dbg(port->dev, "resume done\n");
+
+	return 0;
+}
+
+static const struct dev_pm_ops mtk_pcie_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mtk_pcie_suspend_noirq,
+				      mtk_pcie_resume_noirq)
+};
+
+static const struct of_device_id mtk_pcie_of_match[] = {
+	{ .compatible = "mediatek,mt8192-pcie" },
+	{},
+};
+
+static struct platform_driver mtk_pcie_driver = {
+	.probe = mtk_pcie_probe,
+	.remove = mtk_pcie_remove,
+	.driver = {
+		.name = "mtk-pcie",
+		.of_match_table = mtk_pcie_of_match,
+		.pm = &mtk_pcie_pm_ops,
+	},
+};
+
+module_platform_driver(mtk_pcie_driver);
+MODULE_LICENSE("GPL v2");