@@ -1134,10 +1134,6 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
if (ret)
return ret;
- plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
- if (IS_ERR(plat_dat))
- return PTR_ERR(plat_dat);
-
gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL);
if (!gmac)
return -ENOMEM;
@@ -1201,11 +1197,15 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
ret = of_get_phy_mode(dev->of_node, &interface);
if (ret)
return -EINVAL;
- plat_dat->interface = interface;
+
+ plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+ if (IS_ERR(plat_dat))
+ return PTR_ERR(plat_dat);
/* platform data specifying hardware features and callbacks.
* hardware features were copied from Allwinner drivers.
*/
+ plat_dat->interface = interface;
plat_dat->rx_coe = STMMAC_RX_COE_TYPE2;
plat_dat->tx_coe = 1;
plat_dat->has_sun8i = true;
@@ -1216,7 +1216,7 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv);
if (ret)
- return ret;
+ goto dwmac_deconfig;
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
if (ret)
@@ -1230,7 +1230,7 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
if (gmac->variant->soc_has_internal_phy) {
ret = get_ephy_nodes(priv);
if (ret)
- goto dwmac_exit;
+ goto dwmac_remove;
ret = sun8i_dwmac_register_mdio_mux(priv);
if (ret) {
dev_err(&pdev->dev, "Failed to register mux\n");
@@ -1239,15 +1239,20 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
} else {
ret = sun8i_dwmac_reset(priv);
if (ret)
- goto dwmac_exit;
+ goto dwmac_remove;
}
return ret;
dwmac_mux:
sun8i_dwmac_unset_syscon(gmac);
+dwmac_remove:
+ stmmac_dvr_remove(&pdev->dev);
dwmac_exit:
- stmmac_pltfr_remove(pdev);
-return ret;
+ sun8i_dwmac_exit(pdev, gmac);
+dwmac_deconfig:
+ stmmac_remove_config_dt(pdev, plat_dat);
+
+ return ret;
}
static const struct of_device_id sun8i_dwmac_match[] = {
stmmac_pltfr_remove does three things in one function, making it inapproprate for unwinding the steps in the probe function. Currently, a failure before the call to stmmac_dvr_probe would leak OF node references due to missing a call to stmmac_remove_config_dt. And an error in stmmac_dvr_probe would cause the driver to attempt to remove a netdevice that was never added. Fix these by reordering the init and splitting out the error handling steps. Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path") Signed-off-by: Samuel Holland <samuel@sholland.org> --- .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 25 +++++++++++-------- 1 file changed, 15 insertions(+), 10 deletions(-)