diff --git a/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt b/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt
deleted file mode 100644
index 7cafcb98ead7..000000000000
--- a/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt
+++ /dev/null
@@ -1,80 +0,0 @@
-Clock bindings for ST-Ericsson U300 System Controller Clocks
-
-Bindings for the gated system controller clocks:
-
-Required properties:
-- compatible: must be "stericsson,u300-syscon-clk"
-- #clock-cells: must be <0>
-- clock-type: specifies the type of clock:
-  0 = slow clock
-  1 = fast clock
-  2 = rest/remaining clock
-- clock-id: specifies the clock in the type range
-
-Optional properties:
-- clocks: parent clock(s)
-
-The available clocks per type are as follows:
-
-Type:  ID:   Clock:
--------------------
-0      0     Slow peripheral bridge clock
-0      1     UART0 clock
-0      4     GPIO clock
-0      6     RTC clock
-0      7     Application timer clock
-0      8     Access timer clock
-
-1      0     Fast peripheral bridge clock
-1      1     I2C bus 0 clock
-1      2     I2C bus 1 clock
-1      5     MMC interface peripheral (silicon) clock
-1      6     SPI clock
-
-2      3     CPU clock
-2      4     DMA controller clock
-2      5     External Memory Interface (EMIF) clock
-2      6     NAND flask interface clock
-2      8     XGAM graphics engine clock
-2      9     Shared External Memory Interface (SEMI) clock
-2      10    AHB Subsystem Bridge clock
-2      12    Interrupt controller clock
-
-Example:
-
-gpio_clk: gpio_clk@13M {
-	#clock-cells = <0>;
-	compatible = "stericsson,u300-syscon-clk";
-	clock-type = <0>; /* Slow */
-	clock-id = <4>;
-	clocks = <&slow_clk>;
-};
-
-gpio: gpio@c0016000 {
-	compatible = "stericsson,gpio-coh901";
-	(...)
-	clocks = <&gpio_clk>;
-};
-
-
-Bindings for the MMC/SD card clock:
-
-Required properties:
-- compatible: must be "stericsson,u300-syscon-mclk"
-- #clock-cells: must be <0>
-
-Optional properties:
-- clocks: parent clock(s)
-
-mmc_mclk: mmc_mclk {
-	#clock-cells = <0>;
-	compatible = "stericsson,u300-syscon-mclk";
-	clocks = <&mmc_pclk>;
-};
-
-mmcsd: mmcsd@c0001000 {
-	compatible = "arm,pl18x", "arm,primecell";
-	clocks = <&mmc_pclk>, <&mmc_mclk>;
-	clock-names = "apb_pclk", "mclk";
-	(...)
-};
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 2df2d3080faf..f8d41e430b5c 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -64,7 +64,6 @@ obj-$(CONFIG_COMMON_CLK_STM32F)		+= clk-stm32f4.o
 obj-$(CONFIG_COMMON_CLK_STM32H7)	+= clk-stm32h7.o
 obj-$(CONFIG_COMMON_CLK_STM32MP157)	+= clk-stm32mp1.o
 obj-$(CONFIG_CLK_TWL6040)		+= clk-twl6040.o
-obj-$(CONFIG_ARCH_U300)			+= clk-u300.o
 obj-$(CONFIG_ARCH_VT8500)		+= clk-vt8500.o
 obj-$(CONFIG_COMMON_CLK_VC5)		+= clk-versaclock5.o
 obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
diff --git a/drivers/clk/clk-u300.c b/drivers/clk/clk-u300.c
deleted file mode 100644
index e228c07c4c6e..000000000000
--- a/drivers/clk/clk-u300.c
+++ /dev/null
@@ -1,1199 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * U300 clock implementation
- * Copyright (C) 2007-2012 ST-Ericsson AB
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#include <linux/clkdev.h>
-#include <linux/slab.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/clk-provider.h>
-#include <linux/spinlock.h>
-#include <linux/of.h>
-#include <linux/platform_data/clk-u300.h>
-
-/* APP side SYSCON registers */
-/* CLK Control Register 16bit (R/W) */
-#define U300_SYSCON_CCR						(0x0000)
-#define U300_SYSCON_CCR_I2S1_USE_VCXO				(0x0040)
-#define U300_SYSCON_CCR_I2S0_USE_VCXO				(0x0020)
-#define U300_SYSCON_CCR_TURN_VCXO_ON				(0x0008)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK			(0x0007)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER		(0x04)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW			(0x03)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE		(0x02)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH			(0x01)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST			(0x00)
-/* CLK Status Register 16bit (R/W) */
-#define U300_SYSCON_CSR						(0x0004)
-#define U300_SYSCON_CSR_PLL208_LOCK_IND				(0x0002)
-#define U300_SYSCON_CSR_PLL13_LOCK_IND				(0x0001)
-/* Reset lines for SLOW devices 16bit (R/W) */
-#define U300_SYSCON_RSR						(0x0014)
-#define U300_SYSCON_RSR_PPM_RESET_EN				(0x0200)
-#define U300_SYSCON_RSR_ACC_TMR_RESET_EN			(0x0100)
-#define U300_SYSCON_RSR_APP_TMR_RESET_EN			(0x0080)
-#define U300_SYSCON_RSR_RTC_RESET_EN				(0x0040)
-#define U300_SYSCON_RSR_KEYPAD_RESET_EN				(0x0020)
-#define U300_SYSCON_RSR_GPIO_RESET_EN				(0x0010)
-#define U300_SYSCON_RSR_EH_RESET_EN				(0x0008)
-#define U300_SYSCON_RSR_BTR_RESET_EN				(0x0004)
-#define U300_SYSCON_RSR_UART_RESET_EN				(0x0002)
-#define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN			(0x0001)
-/* Reset lines for FAST devices 16bit (R/W) */
-#define U300_SYSCON_RFR						(0x0018)
-#define U300_SYSCON_RFR_UART1_RESET_ENABLE			(0x0080)
-#define U300_SYSCON_RFR_SPI_RESET_ENABLE			(0x0040)
-#define U300_SYSCON_RFR_MMC_RESET_ENABLE			(0x0020)
-#define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE			(0x0010)
-#define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE			(0x0008)
-#define U300_SYSCON_RFR_I2C1_RESET_ENABLE			(0x0004)
-#define U300_SYSCON_RFR_I2C0_RESET_ENABLE			(0x0002)
-#define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE		(0x0001)
-/* Reset lines for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_RRR						(0x001c)
-#define U300_SYSCON_RRR_CDS_RESET_EN				(0x4000)
-#define U300_SYSCON_RRR_ISP_RESET_EN				(0x2000)
-#define U300_SYSCON_RRR_INTCON_RESET_EN				(0x1000)
-#define U300_SYSCON_RRR_MSPRO_RESET_EN				(0x0800)
-#define U300_SYSCON_RRR_XGAM_RESET_EN				(0x0100)
-#define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN			(0x0080)
-#define U300_SYSCON_RRR_NANDIF_RESET_EN				(0x0040)
-#define U300_SYSCON_RRR_EMIF_RESET_EN				(0x0020)
-#define U300_SYSCON_RRR_DMAC_RESET_EN				(0x0010)
-#define U300_SYSCON_RRR_CPU_RESET_EN				(0x0008)
-#define U300_SYSCON_RRR_APEX_RESET_EN				(0x0004)
-#define U300_SYSCON_RRR_AHB_RESET_EN				(0x0002)
-#define U300_SYSCON_RRR_AAIF_RESET_EN				(0x0001)
-/* Clock enable for SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CESR					(0x0020)
-#define U300_SYSCON_CESR_PPM_CLK_EN				(0x0200)
-#define U300_SYSCON_CESR_ACC_TMR_CLK_EN				(0x0100)
-#define U300_SYSCON_CESR_APP_TMR_CLK_EN				(0x0080)
-#define U300_SYSCON_CESR_KEYPAD_CLK_EN				(0x0040)
-#define U300_SYSCON_CESR_GPIO_CLK_EN				(0x0010)
-#define U300_SYSCON_CESR_EH_CLK_EN				(0x0008)
-#define U300_SYSCON_CESR_BTR_CLK_EN				(0x0004)
-#define U300_SYSCON_CESR_UART_CLK_EN				(0x0002)
-#define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN			(0x0001)
-/* Clock enable for FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CEFR					(0x0024)
-#define U300_SYSCON_CEFR_UART1_CLK_EN				(0x0200)
-#define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN			(0x0100)
-#define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN			(0x0080)
-#define U300_SYSCON_CEFR_SPI_CLK_EN				(0x0040)
-#define U300_SYSCON_CEFR_MMC_CLK_EN				(0x0020)
-#define U300_SYSCON_CEFR_I2S1_CLK_EN				(0x0010)
-#define U300_SYSCON_CEFR_I2S0_CLK_EN				(0x0008)
-#define U300_SYSCON_CEFR_I2C1_CLK_EN				(0x0004)
-#define U300_SYSCON_CEFR_I2C0_CLK_EN				(0x0002)
-#define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN			(0x0001)
-/* Clock enable for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CERR					(0x0028)
-#define U300_SYSCON_CERR_CDS_CLK_EN				(0x2000)
-#define U300_SYSCON_CERR_ISP_CLK_EN				(0x1000)
-#define U300_SYSCON_CERR_MSPRO_CLK_EN				(0x0800)
-#define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN		(0x0400)
-#define U300_SYSCON_CERR_SEMI_CLK_EN				(0x0200)
-#define U300_SYSCON_CERR_XGAM_CLK_EN				(0x0100)
-#define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN			(0x0080)
-#define U300_SYSCON_CERR_NANDIF_CLK_EN				(0x0040)
-#define U300_SYSCON_CERR_EMIF_CLK_EN				(0x0020)
-#define U300_SYSCON_CERR_DMAC_CLK_EN				(0x0010)
-#define U300_SYSCON_CERR_CPU_CLK_EN				(0x0008)
-#define U300_SYSCON_CERR_APEX_CLK_EN				(0x0004)
-#define U300_SYSCON_CERR_AHB_CLK_EN				(0x0002)
-#define U300_SYSCON_CERR_AAIF_CLK_EN				(0x0001)
-/* Single block clock enable 16bit (-/W) */
-#define U300_SYSCON_SBCER					(0x002c)
-#define U300_SYSCON_SBCER_PPM_CLK_EN				(0x0009)
-#define U300_SYSCON_SBCER_ACC_TMR_CLK_EN			(0x0008)
-#define U300_SYSCON_SBCER_APP_TMR_CLK_EN			(0x0007)
-#define U300_SYSCON_SBCER_KEYPAD_CLK_EN				(0x0006)
-#define U300_SYSCON_SBCER_GPIO_CLK_EN				(0x0004)
-#define U300_SYSCON_SBCER_EH_CLK_EN				(0x0003)
-#define U300_SYSCON_SBCER_BTR_CLK_EN				(0x0002)
-#define U300_SYSCON_SBCER_UART_CLK_EN				(0x0001)
-#define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN			(0x0000)
-#define U300_SYSCON_SBCER_UART1_CLK_EN				(0x0019)
-#define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN			(0x0018)
-#define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN			(0x0017)
-#define U300_SYSCON_SBCER_SPI_CLK_EN				(0x0016)
-#define U300_SYSCON_SBCER_MMC_CLK_EN				(0x0015)
-#define U300_SYSCON_SBCER_I2S1_CLK_EN				(0x0014)
-#define U300_SYSCON_SBCER_I2S0_CLK_EN				(0x0013)
-#define U300_SYSCON_SBCER_I2C1_CLK_EN				(0x0012)
-#define U300_SYSCON_SBCER_I2C0_CLK_EN				(0x0011)
-#define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN			(0x0010)
-#define U300_SYSCON_SBCER_CDS_CLK_EN				(0x002D)
-#define U300_SYSCON_SBCER_ISP_CLK_EN				(0x002C)
-#define U300_SYSCON_SBCER_MSPRO_CLK_EN				(0x002B)
-#define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN		(0x002A)
-#define U300_SYSCON_SBCER_SEMI_CLK_EN				(0x0029)
-#define U300_SYSCON_SBCER_XGAM_CLK_EN				(0x0028)
-#define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN			(0x0027)
-#define U300_SYSCON_SBCER_NANDIF_CLK_EN				(0x0026)
-#define U300_SYSCON_SBCER_EMIF_CLK_EN				(0x0025)
-#define U300_SYSCON_SBCER_DMAC_CLK_EN				(0x0024)
-#define U300_SYSCON_SBCER_CPU_CLK_EN				(0x0023)
-#define U300_SYSCON_SBCER_APEX_CLK_EN				(0x0022)
-#define U300_SYSCON_SBCER_AHB_CLK_EN				(0x0021)
-#define U300_SYSCON_SBCER_AAIF_CLK_EN				(0x0020)
-/* Single block clock disable 16bit (-/W) */
-#define U300_SYSCON_SBCDR					(0x0030)
-/* Same values as above for SBCER */
-/* Clock force SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CFSR					(0x003c)
-#define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN			(0x0200)
-#define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN			(0x0100)
-#define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN			(0x0080)
-#define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN			(0x0020)
-#define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN			(0x0010)
-#define U300_SYSCON_CFSR_EH_CLK_FORCE_EN			(0x0008)
-#define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN			(0x0004)
-#define U300_SYSCON_CFSR_UART_CLK_FORCE_EN			(0x0002)
-#define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN		(0x0001)
-/* Clock force FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CFFR					(0x40)
-/* Values not defined. Define if you want to use them. */
-/* Clock force the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CFRR					(0x44)
-#define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN			(0x2000)
-#define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN			(0x1000)
-#define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN			(0x0800)
-#define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN		(0x0400)
-#define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN			(0x0200)
-#define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN			(0x0100)
-#define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN			(0x0080)
-#define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN			(0x0040)
-#define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN			(0x0020)
-#define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN			(0x0010)
-#define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN			(0x0008)
-#define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN			(0x0004)
-#define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN			(0x0002)
-#define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN			(0x0001)
-/* PLL208 Frequency Control 16bit (R/W) */
-#define U300_SYSCON_PFCR					(0x48)
-#define U300_SYSCON_PFCR_DPLL_MULT_NUM				(0x000F)
-/* Power Management Control 16bit (R/W) */
-#define U300_SYSCON_PMCR					(0x50)
-#define U300_SYSCON_PMCR_DCON_ENABLE				(0x0002)
-#define U300_SYSCON_PMCR_PWR_MGNT_ENABLE			(0x0001)
-/* Reset Out 16bit (R/W) */
-#define U300_SYSCON_RCR						(0x6c)
-#define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE			(0x0001)
-/* EMIF Slew Rate Control 16bit (R/W) */
-#define U300_SYSCON_SRCLR					(0x70)
-#define U300_SYSCON_SRCLR_MASK					(0x03FF)
-#define U300_SYSCON_SRCLR_VALUE					(0x03FF)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B			(0x0200)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A			(0x0100)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B			(0x0080)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A			(0x0040)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B			(0x0020)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A			(0x0010)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B			(0x0008)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A			(0x0004)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B			(0x0002)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A			(0x0001)
-/* EMIF Clock Control Register 16bit (R/W) */
-#define U300_SYSCON_ECCR					(0x0078)
-#define U300_SYSCON_ECCR_MASK					(0x000F)
-#define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE		(0x0008)
-#define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE	(0x0004)
-#define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE		(0x0002)
-#define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE		(0x0001)
-/* MMC/MSPRO frequency divider register 0 16bit (R/W) */
-#define U300_SYSCON_MMF0R					(0x90)
-#define U300_SYSCON_MMF0R_MASK					(0x00FF)
-#define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK			(0x00F0)
-#define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK			(0x000F)
-/* MMC/MSPRO frequency divider register 1 16bit (R/W) */
-#define U300_SYSCON_MMF1R					(0x94)
-#define U300_SYSCON_MMF1R_MASK					(0x00FF)
-#define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK			(0x00F0)
-#define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK			(0x000F)
-/* Clock control for the MMC and MSPRO blocks 16bit (R/W) */
-#define U300_SYSCON_MMCR					(0x9C)
-#define U300_SYSCON_MMCR_MASK					(0x0003)
-#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE			(0x0002)
-#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE			(0x0001)
-/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
-#define U300_SYSCON_S0CCR					(0x120)
-#define U300_SYSCON_S0CCR_FIELD_MASK				(0x43FF)
-#define U300_SYSCON_S0CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S0CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S0CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S0CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S0CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */
-#define U300_SYSCON_S1CCR					(0x124)
-#define U300_SYSCON_S1CCR_FIELD_MASK				(0x43FF)
-#define U300_SYSCON_S1CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S1CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S1CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S1CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S1CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SYS_2_CLK_CONTROL third clock control 16 bit (R/W) */
-#define U300_SYSCON_S2CCR					(0x128)
-#define U300_SYSCON_S2CCR_FIELD_MASK				(0xC3FF)
-#define U300_SYSCON_S2CCR_CLK_STEAL				(0x8000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ				(0x4000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR			(0x2000)
-#define U300_SYSCON_S2CCR_CLOCK_INV				(0x0200)
-#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK			(0x01E0)
-#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK			(0x001E)
-#define U300_SYSCON_S2CCR_CLOCK_ENABLE				(0x0001)
-#define U300_SYSCON_S2CCR_SEL_MCLK				(0x8 << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK			(0xA << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK			(0xC << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK			(0xD << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK			(0xE << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK			(0x0 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK			(0x2 << 1)
-#define U300_SYSCON_S2CCR_SEL_RTC_CLK				(0x4 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK			(0x6 << 1)
-/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
-#define U300_SYSCON_PICR					(0x0130)
-#define U300_SYSCON_PICR_MASK					(0x00FF)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE		(0x0080)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE		(0x0040)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE		(0x0020)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE		(0x0010)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE		(0x0008)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE		(0x0004)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE		(0x0002)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE		(0x0001)
-/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
-#define U300_SYSCON_PISR					(0x0134)
-#define U300_SYSCON_PISR_MASK					(0x000F)
-#define U300_SYSCON_PISR_PLL13_UNLOCK_IND			(0x0008)
-#define U300_SYSCON_PISR_PLL13_LOCK_IND				(0x0004)
-#define U300_SYSCON_PISR_PLL208_UNLOCK_IND			(0x0002)
-#define U300_SYSCON_PISR_PLL208_LOCK_IND			(0x0001)
-/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
-#define U300_SYSCON_PICLR					(0x0138)
-#define U300_SYSCON_PICLR_MASK					(0x000F)
-#define U300_SYSCON_PICLR_RWMASK				(0x0000)
-#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC			(0x0008)
-#define U300_SYSCON_PICLR_PLL13_LOCK_SC				(0x0004)
-#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC			(0x0002)
-#define U300_SYSCON_PICLR_PLL208_LOCK_SC			(0x0001)
-/* Clock activity observability register 0 */
-#define U300_SYSCON_C0OAR					(0x140)
-#define U300_SYSCON_C0OAR_MASK					(0xFFFF)
-#define U300_SYSCON_C0OAR_VALUE					(0xFFFF)
-#define U300_SYSCON_C0OAR_BT_H_CLK				(0x8000)
-#define U300_SYSCON_C0OAR_ASPB_P_CLK				(0x4000)
-#define U300_SYSCON_C0OAR_APP_SEMI_H_CLK			(0x2000)
-#define U300_SYSCON_C0OAR_APP_SEMI_CLK				(0x1000)
-#define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK			(0x0800)
-#define U300_SYSCON_C0OAR_APP_I2S1_CLK				(0x0400)
-#define U300_SYSCON_C0OAR_APP_I2S0_CLK				(0x0200)
-#define U300_SYSCON_C0OAR_APP_CPU_CLK				(0x0100)
-#define U300_SYSCON_C0OAR_APP_52_CLK				(0x0080)
-#define U300_SYSCON_C0OAR_APP_208_CLK				(0x0040)
-#define U300_SYSCON_C0OAR_APP_104_CLK				(0x0020)
-#define U300_SYSCON_C0OAR_APEX_CLK				(0x0010)
-#define U300_SYSCON_C0OAR_AHPB_M_H_CLK				(0x0008)
-#define U300_SYSCON_C0OAR_AHB_CLK				(0x0004)
-#define U300_SYSCON_C0OAR_AFPB_P_CLK				(0x0002)
-#define U300_SYSCON_C0OAR_AAIF_CLK				(0x0001)
-/* Clock activity observability register 1 */
-#define U300_SYSCON_C1OAR					(0x144)
-#define U300_SYSCON_C1OAR_MASK					(0x3FFE)
-#define U300_SYSCON_C1OAR_VALUE					(0x3FFE)
-#define U300_SYSCON_C1OAR_NFIF_F_CLK				(0x2000)
-#define U300_SYSCON_C1OAR_MSPRO_CLK				(0x1000)
-#define U300_SYSCON_C1OAR_MMC_P_CLK				(0x0800)
-#define U300_SYSCON_C1OAR_MMC_CLK				(0x0400)
-#define U300_SYSCON_C1OAR_KP_P_CLK				(0x0200)
-#define U300_SYSCON_C1OAR_I2C1_P_CLK				(0x0100)
-#define U300_SYSCON_C1OAR_I2C0_P_CLK				(0x0080)
-#define U300_SYSCON_C1OAR_GPIO_CLK				(0x0040)
-#define U300_SYSCON_C1OAR_EMIF_MPMC_CLK				(0x0020)
-#define U300_SYSCON_C1OAR_EMIF_H_CLK				(0x0010)
-#define U300_SYSCON_C1OAR_EVHIST_CLK				(0x0008)
-#define U300_SYSCON_C1OAR_PPM_CLK				(0x0004)
-#define U300_SYSCON_C1OAR_DMA_CLK				(0x0002)
-/* Clock activity observability register 2 */
-#define U300_SYSCON_C2OAR					(0x148)
-#define U300_SYSCON_C2OAR_MASK					(0x0FFF)
-#define U300_SYSCON_C2OAR_VALUE					(0x0FFF)
-#define U300_SYSCON_C2OAR_XGAM_CDI_CLK				(0x0800)
-#define U300_SYSCON_C2OAR_XGAM_CLK				(0x0400)
-#define U300_SYSCON_C2OAR_VC_H_CLK				(0x0200)
-#define U300_SYSCON_C2OAR_VC_CLK				(0x0100)
-#define U300_SYSCON_C2OAR_UA_P_CLK				(0x0080)
-#define U300_SYSCON_C2OAR_TMR1_CLK				(0x0040)
-#define U300_SYSCON_C2OAR_TMR0_CLK				(0x0020)
-#define U300_SYSCON_C2OAR_SPI_P_CLK				(0x0010)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK			(0x0008)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CLK				(0x0004)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK			(0x0002)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CLK				(0x0001)
-
-
-/*
- * The clocking hierarchy currently looks like this.
- * NOTE: the idea is NOT to show how the clocks are routed on the chip!
- * The ideas is to show dependencies, so a clock higher up in the
- * hierarchy has to be on in order for another clock to be on. Now,
- * both CPU and DMA can actually be on top of the hierarchy, and that
- * is not modeled currently. Instead we have the backbone AMBA bus on
- * top. This bus cannot be programmed in any way but conceptually it
- * needs to be active for the bridges and devices to transport data.
- *
- * Please be aware that a few clocks are hw controlled, which mean that
- * the hw itself can turn on/off or change the rate of the clock when
- * needed!
- *
- *  AMBA bus
- *  |
- *  +- CPU
- *  +- FSMC NANDIF NAND Flash interface
- *  +- SEMI Shared Memory interface
- *  +- ISP Image Signal Processor (U335 only)
- *  +- CDS (U335 only)
- *  +- DMA Direct Memory Access Controller
- *  +- AAIF APP/ACC Interface (Mobile Scalable Link, MSL)
- *  +- APEX
- *  +- VIDEO_ENC AVE2/3 Video Encoder
- *  +- XGAM Graphics Accelerator Controller
- *  +- AHB
- *  |
- *  +- ahb:0 AHB Bridge
- *  |  |
- *  |  +- ahb:1 INTCON Interrupt controller
- *  |  +- ahb:3 MSPRO  Memory Stick Pro controller
- *  |  +- ahb:4 EMIF   External Memory interface
- *  |
- *  +- fast:0 FAST bridge
- *  |  |
- *  |  +- fast:1 MMCSD MMC/SD card reader controller
- *  |  +- fast:2 I2S0  PCM I2S channel 0 controller
- *  |  +- fast:3 I2S1  PCM I2S channel 1 controller
- *  |  +- fast:4 I2C0  I2C channel 0 controller
- *  |  +- fast:5 I2C1  I2C channel 1 controller
- *  |  +- fast:6 SPI   SPI controller
- *  |  +- fast:7 UART1 Secondary UART (U335 only)
- *  |
- *  +- slow:0 SLOW bridge
- *     |
- *     +- slow:1 SYSCON (not possible to control)
- *     +- slow:2 WDOG Watchdog
- *     +- slow:3 UART0 primary UART
- *     +- slow:4 TIMER_APP Application timer - used in Linux
- *     +- slow:5 KEYPAD controller
- *     +- slow:6 GPIO controller
- *     +- slow:7 RTC controller
- *     +- slow:8 BT Bus Tracer (not used currently)
- *     +- slow:9 EH Event Handler (not used currently)
- *     +- slow:a TIMER_ACC Access style timer (not used currently)
- *     +- slow:b PPM (U335 only, what is that?)
- */
-
-/* Global syscon virtual base */
-static void __iomem *syscon_vbase;
-
-/**
- * struct clk_syscon - U300 syscon clock
- * @hw: corresponding clock hardware entry
- * @hw_ctrld: whether this clock is hardware controlled (for refcount etc)
- *	and does not need any magic pokes to be enabled/disabled
- * @reset: state holder, whether this block's reset line is asserted or not
- * @res_reg: reset line enable/disable flag register
- * @res_bit: bit for resetting or taking this consumer out of reset
- * @en_reg: clock line enable/disable flag register
- * @en_bit: bit for enabling/disabling this consumer clock line
- * @clk_val: magic value to poke in the register to enable/disable
- *	this one clock
- */
-struct clk_syscon {
-	struct clk_hw hw;
-	bool hw_ctrld;
-	bool reset;
-	void __iomem *res_reg;
-	u8 res_bit;
-	void __iomem *en_reg;
-	u8 en_bit;
-	u16 clk_val;
-};
-
-#define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw)
-
-static DEFINE_SPINLOCK(syscon_resetreg_lock);
-
-/*
- * Reset control functions. We remember if a block has been
- * taken out of reset and don't remove the reset assertion again
- * and vice versa. Currently we only remove resets so the
- * enablement function is defined out.
- */
-static void syscon_block_reset_enable(struct clk_syscon *sclk)
-{
-	unsigned long iflags;
-	u16 val;
-
-	/* Not all blocks support resetting */
-	if (!sclk->res_reg)
-		return;
-	spin_lock_irqsave(&syscon_resetreg_lock, iflags);
-	val = readw(sclk->res_reg);
-	val |= BIT(sclk->res_bit);
-	writew(val, sclk->res_reg);
-	spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
-	sclk->reset = true;
-}
-
-static void syscon_block_reset_disable(struct clk_syscon *sclk)
-{
-	unsigned long iflags;
-	u16 val;
-
-	/* Not all blocks support resetting */
-	if (!sclk->res_reg)
-		return;
-	spin_lock_irqsave(&syscon_resetreg_lock, iflags);
-	val = readw(sclk->res_reg);
-	val &= ~BIT(sclk->res_bit);
-	writew(val, sclk->res_reg);
-	spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
-	sclk->reset = false;
-}
-
-static int syscon_clk_prepare(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* If the block is in reset, bring it out */
-	if (sclk->reset)
-		syscon_block_reset_disable(sclk);
-	return 0;
-}
-
-static void syscon_clk_unprepare(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Please don't force the console into reset */
-	if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
-		return;
-	/* When unpreparing, force block into reset */
-	if (!sclk->reset)
-		syscon_block_reset_enable(sclk);
-}
-
-static int syscon_clk_enable(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Don't touch the hardware controlled clocks */
-	if (sclk->hw_ctrld)
-		return 0;
-	/* These cannot be controlled */
-	if (sclk->clk_val == 0xFFFFU)
-		return 0;
-
-	writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER);
-	return 0;
-}
-
-static void syscon_clk_disable(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	/* Don't touch the hardware controlled clocks */
-	if (sclk->hw_ctrld)
-		return;
-	if (sclk->clk_val == 0xFFFFU)
-		return;
-	/* Please don't disable the console port */
-	if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
-		return;
-
-	writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR);
-}
-
-static int syscon_clk_is_enabled(struct clk_hw *hw)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 val;
-
-	/* If no enable register defined, it's always-on */
-	if (!sclk->en_reg)
-		return 1;
-
-	val = readw(sclk->en_reg);
-	val &= BIT(sclk->en_bit);
-
-	return val ? 1 : 0;
-}
-
-static u16 syscon_get_perf(void)
-{
-	u16 val;
-
-	val = readw(syscon_vbase + U300_SYSCON_CCR);
-	val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
-	return val;
-}
-
-static unsigned long
-syscon_clk_recalc_rate(struct clk_hw *hw,
-		       unsigned long parent_rate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 perf = syscon_get_perf();
-
-	switch (sclk->clk_val) {
-	case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN:
-	case U300_SYSCON_SBCER_I2C0_CLK_EN:
-	case U300_SYSCON_SBCER_I2C1_CLK_EN:
-	case U300_SYSCON_SBCER_MMC_CLK_EN:
-	case U300_SYSCON_SBCER_SPI_CLK_EN:
-		/* The FAST clocks have one progression */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		default:
-			return parent_rate; /* 26 MHz */
-		}
-	case U300_SYSCON_SBCER_DMAC_CLK_EN:
-	case U300_SYSCON_SBCER_NANDIF_CLK_EN:
-	case U300_SYSCON_SBCER_XGAM_CLK_EN:
-		/* AMBA interconnect peripherals */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 6500000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 26000000;
-		default:
-			return parent_rate; /* 52 MHz */
-		}
-	case U300_SYSCON_SBCER_SEMI_CLK_EN:
-	case U300_SYSCON_SBCER_EMIF_CLK_EN:
-		/* EMIF speeds */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 52000000;
-		default:
-			return 104000000;
-		}
-	case U300_SYSCON_SBCER_CPU_CLK_EN:
-		/* And the fast CPU clock */
-		switch (perf) {
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-			return 13000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-			return 52000000;
-		case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
-			return 104000000;
-		default:
-			return parent_rate; /* 208 MHz */
-		}
-	default:
-		/*
-		 * The SLOW clocks and default just inherit the rate of
-		 * their parent (typically PLL13 13 MHz).
-		 */
-		return parent_rate;
-	}
-}
-
-static long
-syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate,
-		      unsigned long *prate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-
-	if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
-		return *prate;
-	/* We really only support setting the rate of the CPU clock */
-	if (rate <= 13000000)
-		return 13000000;
-	if (rate <= 52000000)
-		return 52000000;
-	if (rate <= 104000000)
-		return 104000000;
-	return 208000000;
-}
-
-static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate,
-			       unsigned long parent_rate)
-{
-	struct clk_syscon *sclk = to_syscon(hw);
-	u16 val;
-
-	/* We only support setting the rate of the CPU clock */
-	if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
-		return -EINVAL;
-	switch (rate) {
-	case 13000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER;
-		break;
-	case 52000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE;
-		break;
-	case 104000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH;
-		break;
-	case 208000000:
-		val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST;
-		break;
-	default:
-		return -EINVAL;
-	}
-	val |= readw(syscon_vbase + U300_SYSCON_CCR) &
-		~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ;
-	writew(val, syscon_vbase + U300_SYSCON_CCR);
-	return 0;
-}
-
-static const struct clk_ops syscon_clk_ops = {
-	.prepare = syscon_clk_prepare,
-	.unprepare = syscon_clk_unprepare,
-	.enable = syscon_clk_enable,
-	.disable = syscon_clk_disable,
-	.is_enabled = syscon_clk_is_enabled,
-	.recalc_rate = syscon_clk_recalc_rate,
-	.round_rate = syscon_clk_round_rate,
-	.set_rate = syscon_clk_set_rate,
-};
-
-static struct clk_hw * __init
-syscon_clk_register(struct device *dev, const char *name,
-		    const char *parent_name, unsigned long flags,
-		    bool hw_ctrld,
-		    void __iomem *res_reg, u8 res_bit,
-		    void __iomem *en_reg, u8 en_bit,
-		    u16 clk_val)
-{
-	struct clk_hw *hw;
-	struct clk_syscon *sclk;
-	struct clk_init_data init;
-	int ret;
-
-	sclk = kzalloc(sizeof(*sclk), GFP_KERNEL);
-	if (!sclk)
-		return ERR_PTR(-ENOMEM);
-
-	init.name = name;
-	init.ops = &syscon_clk_ops;
-	init.flags = flags;
-	init.parent_names = (parent_name ? &parent_name : NULL);
-	init.num_parents = (parent_name ? 1 : 0);
-	sclk->hw.init = &init;
-	sclk->hw_ctrld = hw_ctrld;
-	/* Assume the block is in reset at registration */
-	sclk->reset = true;
-	sclk->res_reg = res_reg;
-	sclk->res_bit = res_bit;
-	sclk->en_reg = en_reg;
-	sclk->en_bit = en_bit;
-	sclk->clk_val = clk_val;
-
-	hw = &sclk->hw;
-	ret = clk_hw_register(dev, hw);
-	if (ret) {
-		kfree(sclk);
-		hw = ERR_PTR(ret);
-	}
-
-	return hw;
-}
-
-#define U300_CLK_TYPE_SLOW 0
-#define U300_CLK_TYPE_FAST 1
-#define U300_CLK_TYPE_REST 2
-
-/**
- * struct u300_clock - defines the bits and pieces for a certain clock
- * @type: the clock type, slow fast or rest
- * @id: the bit in the slow/fast/rest register for this clock
- * @hw_ctrld: whether the clock is hardware controlled
- * @clk_val: a value to poke in the one-write enable/disable registers
- */
-struct u300_clock {
-	u8 type;
-	u8 id;
-	bool hw_ctrld;
-	u16 clk_val;
-};
-
-static struct u300_clock const u300_clk_lookup[] __initconst = {
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 3,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_CPU_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 4,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 5,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 6,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 8,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 9,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 10,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_REST,
-		.id = 12,
-		.hw_ctrld = false,
-		/* INTCON: cannot be enabled, just taken out of reset */
-		.clk_val = 0xFFFFU,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 0,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 1,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 2,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 5,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_MMC_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_FAST,
-		.id = 6,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_SPI_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 0,
-		.hw_ctrld = true,
-		.clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 1,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_UART_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 4,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 6,
-		.hw_ctrld = true,
-		/* No clock enable register bit */
-		.clk_val = 0xFFFFU,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 7,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN,
-	},
-	{
-		.type = U300_CLK_TYPE_SLOW,
-		.id = 8,
-		.hw_ctrld = false,
-		.clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN,
-	},
-};
-
-static void __init of_u300_syscon_clk_init(struct device_node *np)
-{
-	struct clk_hw *hw = ERR_PTR(-EINVAL);
-	const char *clk_name = np->name;
-	const char *parent_name;
-	void __iomem *res_reg;
-	void __iomem *en_reg;
-	u32 clk_type;
-	u32 clk_id;
-	int i;
-
-	if (of_property_read_u32(np, "clock-type", &clk_type)) {
-		pr_err("%s: syscon clock \"%s\" missing clock-type property\n",
-		       __func__, clk_name);
-		return;
-	}
-	if (of_property_read_u32(np, "clock-id", &clk_id)) {
-		pr_err("%s: syscon clock \"%s\" missing clock-id property\n",
-		       __func__, clk_name);
-		return;
-	}
-	parent_name = of_clk_get_parent_name(np, 0);
-
-	switch (clk_type) {
-	case U300_CLK_TYPE_SLOW:
-		res_reg = syscon_vbase + U300_SYSCON_RSR;
-		en_reg = syscon_vbase + U300_SYSCON_CESR;
-		break;
-	case U300_CLK_TYPE_FAST:
-		res_reg = syscon_vbase + U300_SYSCON_RFR;
-		en_reg = syscon_vbase + U300_SYSCON_CEFR;
-		break;
-	case U300_CLK_TYPE_REST:
-		res_reg = syscon_vbase + U300_SYSCON_RRR;
-		en_reg = syscon_vbase + U300_SYSCON_CERR;
-		break;
-	default:
-		pr_err("unknown clock type %x specified\n", clk_type);
-		return;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) {
-		const struct u300_clock *u3clk = &u300_clk_lookup[i];
-
-		if (u3clk->type == clk_type && u3clk->id == clk_id)
-			hw = syscon_clk_register(NULL, clk_name, parent_name,
-						 0, u3clk->hw_ctrld,
-						 res_reg, u3clk->id,
-						 en_reg, u3clk->id,
-						 u3clk->clk_val);
-	}
-
-	if (!IS_ERR(hw)) {
-		of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-
-		/*
-		 * Some few system clocks - device tree does not
-		 * represent clocks without a corresponding device node.
-		 * for now we add these three clocks here.
-		 */
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 5)
-			clk_hw_register_clkdev(hw, NULL, "pl172");
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 9)
-			clk_hw_register_clkdev(hw, NULL, "semi");
-		if (clk_type == U300_CLK_TYPE_REST && clk_id == 12)
-			clk_hw_register_clkdev(hw, NULL, "intcon");
-	}
-}
-
-/**
- * struct clk_mclk - U300 MCLK clock (MMC/SD clock)
- * @hw: corresponding clock hardware entry
- * @is_mspro: if this is the memory stick clock rather than MMC/SD
- */
-struct clk_mclk {
-	struct clk_hw hw;
-	bool is_mspro;
-};
-
-#define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw)
-
-static int mclk_clk_prepare(struct clk_hw *hw)
-{
-	struct clk_mclk *mclk = to_mclk(hw);
-	u16 val;
-
-	/* The MMC and MSPRO clocks need some special set-up */
-	if (!mclk->is_mspro) {
-		/* Set default MMC clock divisor to 18.9 MHz */
-		writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R);
-		val = readw(syscon_vbase + U300_SYSCON_MMCR);
-		/* Disable the MMC feedback clock */
-		val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
-		/* Disable MSPRO frequency */
-		val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
-		writew(val, syscon_vbase + U300_SYSCON_MMCR);
-	} else {
-		val = readw(syscon_vbase + U300_SYSCON_MMCR);
-		/* Disable the MMC feedback clock */
-		val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
-		/* Enable MSPRO frequency */
-		val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
-		writew(val, syscon_vbase + U300_SYSCON_MMCR);
-	}
-
-	return 0;
-}
-
-static unsigned long
-mclk_clk_recalc_rate(struct clk_hw *hw,
-		     unsigned long parent_rate)
-{
-	u16 perf = syscon_get_perf();
-
-	switch (perf) {
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
-		/*
-		 * Here, the 208 MHz PLL gets shut down and the always
-		 * on 13 MHz PLL used for RTC etc kicks into use
-		 * instead.
-		 */
-		return 13000000;
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
-	case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
-	{
-		/*
-		 * This clock is under program control. The register is
-		 * divided in two nybbles, bit 7-4 gives cycles-1 to count
-		 * high, bit 3-0 gives cycles-1 to count low. Distribute
-		 * these with no more than 1 cycle difference between
-		 * low and high and add low and high to get the actual
-		 * divisor. The base PLL is 208 MHz. Writing 0x00 will
-		 * divide by 1 and 1 so the highest frequency possible
-		 * is 104 MHz.
-		 *
-		 * e.g. 0x54 =>
-		 * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
-		 */
-		u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) &
-			U300_SYSCON_MMF0R_MASK;
-		switch (val) {
-		case 0x0054:
-			return 18900000;
-		case 0x0044:
-			return 20800000;
-		case 0x0043:
-			return 23100000;
-		case 0x0033:
-			return 26000000;
-		case 0x0032:
-			return 29700000;
-		case 0x0022:
-			return 34700000;
-		case 0x0021:
-			return 41600000;
-		case 0x0011:
-			return 52000000;
-		case 0x0000:
-			return 104000000;
-		default:
-			break;
-		}
-	}
-	default:
-		break;
-	}
-	return parent_rate;
-}
-
-static long
-mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate,
-		    unsigned long *prate)
-{
-	if (rate <= 18900000)
-		return 18900000;
-	if (rate <= 20800000)
-		return 20800000;
-	if (rate <= 23100000)
-		return 23100000;
-	if (rate <= 26000000)
-		return 26000000;
-	if (rate <= 29700000)
-		return 29700000;
-	if (rate <= 34700000)
-		return 34700000;
-	if (rate <= 41600000)
-		return 41600000;
-	/* Highest rate */
-	return 52000000;
-}
-
-static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate,
-			     unsigned long parent_rate)
-{
-	u16 val;
-	u16 reg;
-
-	switch (rate) {
-	case 18900000:
-		val = 0x0054;
-		break;
-	case 20800000:
-		val = 0x0044;
-		break;
-	case 23100000:
-		val = 0x0043;
-		break;
-	case 26000000:
-		val = 0x0033;
-		break;
-	case 29700000:
-		val = 0x0032;
-		break;
-	case 34700000:
-		val = 0x0022;
-		break;
-	case 41600000:
-		val = 0x0021;
-		break;
-	case 52000000:
-		val = 0x0011;
-		break;
-	case 104000000:
-		val = 0x0000;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	reg = readw(syscon_vbase + U300_SYSCON_MMF0R) &
-		~U300_SYSCON_MMF0R_MASK;
-	writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R);
-	return 0;
-}
-
-static const struct clk_ops mclk_ops = {
-	.prepare = mclk_clk_prepare,
-	.recalc_rate = mclk_clk_recalc_rate,
-	.round_rate = mclk_clk_round_rate,
-	.set_rate = mclk_clk_set_rate,
-};
-
-static struct clk_hw * __init
-mclk_clk_register(struct device *dev, const char *name,
-		  const char *parent_name, bool is_mspro)
-{
-	struct clk_hw *hw;
-	struct clk_mclk *mclk;
-	struct clk_init_data init;
-	int ret;
-
-	mclk = kzalloc(sizeof(*mclk), GFP_KERNEL);
-	if (!mclk)
-		return ERR_PTR(-ENOMEM);
-
-	init.name = "mclk";
-	init.ops = &mclk_ops;
-	init.flags = 0;
-	init.parent_names = (parent_name ? &parent_name : NULL);
-	init.num_parents = (parent_name ? 1 : 0);
-	mclk->hw.init = &init;
-	mclk->is_mspro = is_mspro;
-
-	hw = &mclk->hw;
-	ret = clk_hw_register(dev, hw);
-	if (ret) {
-		kfree(mclk);
-		hw = ERR_PTR(ret);
-	}
-
-	return hw;
-}
-
-static void __init of_u300_syscon_mclk_init(struct device_node *np)
-{
-	struct clk_hw *hw;
-	const char *clk_name = np->name;
-	const char *parent_name;
-
-	parent_name = of_clk_get_parent_name(np, 0);
-	hw = mclk_clk_register(NULL, clk_name, parent_name, false);
-	if (!IS_ERR(hw))
-		of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-}
-
-static const struct of_device_id u300_clk_match[] __initconst = {
-	{
-		.compatible = "fixed-clock",
-		.data = of_fixed_clk_setup,
-	},
-	{
-		.compatible = "fixed-factor-clock",
-		.data = of_fixed_factor_clk_setup,
-	},
-	{
-		.compatible = "stericsson,u300-syscon-clk",
-		.data = of_u300_syscon_clk_init,
-	},
-	{
-		.compatible = "stericsson,u300-syscon-mclk",
-		.data = of_u300_syscon_mclk_init,
-	},
-	{}
-};
-
-
-void __init u300_clk_init(void __iomem *base)
-{
-	u16 val;
-
-	syscon_vbase = base;
-
-	/* Set system to run at PLL208, max performance, a known state. */
-	val = readw(syscon_vbase + U300_SYSCON_CCR);
-	val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
-	writew(val, syscon_vbase + U300_SYSCON_CCR);
-	/* Wait for the PLL208 to lock if not locked in yet */
-	while (!(readw(syscon_vbase + U300_SYSCON_CSR) &
-		 U300_SYSCON_CSR_PLL208_LOCK_IND));
-
-	/* Power management enable */
-	val = readw(syscon_vbase + U300_SYSCON_PMCR);
-	val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE;
-	writew(val, syscon_vbase + U300_SYSCON_PMCR);
-
-	of_clk_init(u300_clk_match);
-}
diff --git a/include/linux/platform_data/clk-u300.h b/include/linux/platform_data/clk-u300.h
deleted file mode 100644
index 8429e73911a1..000000000000
--- a/include/linux/platform_data/clk-u300.h
+++ /dev/null
@@ -1 +0,0 @@
-void __init u300_clk_init(void __iomem *base);
