[stable,v5.10,5/7] arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges

Commit Message

Jing Xiangfeng March 3, 2021, 7:33 a.m. UTC

From: Nicolas Saenz Julienne <[e-mail]>

commit 8424ecdde7df99d5426e1a1fd9f0fb36f4183032 upstream

We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)

The DMA layer also needs to be able to allocate memory that is
guaranteed to meet those DMA constraints, for bounce buffering as well
as allocating the backing for consistent mappings. This is why the 1 GB
ZONE_DMA was introduced recently. Unfortunately, it turns out the having
a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and
potentially in other places where allocations cannot cross zone
boundaries. Therefore, we should avoid having two separate DMA zones
when possible.

So, with the help of of_dma_get_max_cpu_address() get the topmost
physical address accessible to all DMA masters in system and use that
information to fine-tune ZONE_DMA's size. In the absence of addressing
limited masters ZONE_DMA will span the whole 32-bit address space,
otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit
address space, and have ZONE_DMA32 cover the rest of the 32-bit address
space.

Signed-off-by: Nicolas Saenz Julienne <[e-mail]>
Link: https://lore.kernel.org/r/[e-mail]
Signed-off-by: Catalin Marinas <[e-mail]>
Cc: <[e-mail]>
Signed-off-by: Jing Xiangfeng <[e-mail]>
---
 arch/arm64/mm/init.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

Patch

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index 7da912bf4222..05a1c2773629 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -42,8 +42,6 @@ 
 #include <asm/tlb.h>
 #include <asm/alternative.h>
 
-#define ARM64_ZONE_DMA_BITS	30
-
 /*
  * We need to be able to catch inadvertent references to memstart_addr
  * that occur (potentially in generic code) before arm64_memblock_init()
@@ -188,9 +186,11 @@  static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
 static void __init zone_sizes_init(unsigned long min, unsigned long max)
 {
 	unsigned long max_zone_pfns[MAX_NR_ZONES]  = {0};
+	unsigned int __maybe_unused dt_zone_dma_bits;
 
 #ifdef CONFIG_ZONE_DMA
-	zone_dma_bits = ARM64_ZONE_DMA_BITS;
+	dt_zone_dma_bits = fls64(of_dma_get_max_cpu_address(NULL));
+	zone_dma_bits = min(32U, dt_zone_dma_bits);
 	arm64_dma_phys_limit = max_zone_phys(zone_dma_bits);
 	max_zone_pfns[ZONE_DMA] = PFN_DOWN(arm64_dma_phys_limit);
 #endif