| Message ID | 20210308233858.24741-4-daniel.lezcano@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [RESEND,v5,1/4] dt-bindings: devfreq: rk3399_dmc: Add rockchip, pmu phandle. | expand |
On 3/9/21 8:38 AM, Daniel Lezcano wrote: > From: Gaël PORTAY <gael.portay@collabora.com> > > Those DDR related defines do not exist. Replace their references with > their numerical constant. > > Signed-off-by: Gaël PORTAY <gael.portay@collabora.com> > Reviewed-by: Rob Herring <robh@kernel.org> > Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> > --- > .../bindings/devfreq/rk3399_dmc.txt | 73 +++++++++---------- > 1 file changed, 34 insertions(+), 39 deletions(-) > > diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt > index a41bcfef95c8..ddde2c4f97df 100644 > --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt > +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt > @@ -79,24 +79,23 @@ Following properties relate to DDR timing: > > - rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines > the DRAM side driver strength in ohms. Default > - value is DDR3_DS_40ohm. > + value is 40. > > - rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines > the DRAM side ODT strength in ohms. Default value > - is DDR3_ODT_120ohm. > + is 120. > > - rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines > the phy side CA line (incluing command line, > address line and clock line) driver strength. > - Default value is PHY_DRV_ODT_40. > + Default value is 40. > > - rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines > the PHY side DQ line (including DQS/DQ/DM line) > - driver strength. Default value is PHY_DRV_ODT_40. > + driver strength. Default value is 40. > > - rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines > - the PHY side ODT strength. Default value is > - PHY_DRV_ODT_240. > + the PHY side ODT strength. Default value is 240. > > - rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines > then ODT disable frequency in MHz (Mega Hz). > @@ -106,25 +105,23 @@ Following properties relate to DDR timing: > > - rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines > the DRAM side driver strength in ohms. Default > - value is LP3_DS_34ohm. > + value is 34. > > - rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines > the DRAM side ODT strength in ohms. Default value > - is LP3_ODT_240ohm. > + is 240. > > - rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines > the PHY side CA line (including command line, > address line and clock line) driver strength. > - Default value is PHY_DRV_ODT_40. > + Default value is 40. > > - rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines > the PHY side DQ line (including DQS/DQ/DM line) > - driver strength. Default value is > - PHY_DRV_ODT_40. > + driver strength. Default value is 40. > > - rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define > - the phy side odt strength, default value is > - PHY_DRV_ODT_240. > + the phy side odt strength, default value is 240. > > - rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter > defines the ODT disable frequency in > @@ -134,32 +131,30 @@ Following properties relate to DDR timing: > > - rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines > the DRAM side driver strength in ohms. Default > - value is LP4_PDDS_60ohm. > + value is 60. > > - rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines > the DRAM side ODT on DQS/DQ line strength in ohms. > - Default value is LP4_DQ_ODT_40ohm. > + Default value is 40. > > - rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines > the DRAM side ODT on CA line strength in ohms. > - Default value is LP4_CA_ODT_40ohm. > + Default value is 40. > > - rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines > the PHY side CA line (including command address > - line) driver strength. Default value is > - PHY_DRV_ODT_40. > + line) driver strength. Default value is 40. > > - rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines > the PHY side clock line and CS line driver > - strength. Default value is PHY_DRV_ODT_80. > + strength. Default value is 80. > > - rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines > the PHY side DQ line (including DQS/DQ/DM line) > - driver strength. Default value is PHY_DRV_ODT_80. > + driver strength. Default value is 80. > > - rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines > - the PHY side ODT strength. Default value is > - PHY_DRV_ODT_60. > + the PHY side ODT strength. Default value is 60. > > Example: > dmc_opp_table: dmc_opp_table { > @@ -195,23 +190,23 @@ Example: > rockchip,phy_dll_dis_freq = <125>; > rockchip,auto_pd_dis_freq = <666>; > rockchip,ddr3_odt_dis_freq = <333>; > - rockchip,ddr3_drv = <DDR3_DS_40ohm>; > - rockchip,ddr3_odt = <DDR3_ODT_120ohm>; > - rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>; > - rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>; > - rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>; > + rockchip,ddr3_drv = <40>; > + rockchip,ddr3_odt = <120>; > + rockchip,phy_ddr3_ca_drv = <40>; > + rockchip,phy_ddr3_dq_drv = <40>; > + rockchip,phy_ddr3_odt = <240>; > rockchip,lpddr3_odt_dis_freq = <333>; > - rockchip,lpddr3_drv = <LP3_DS_34ohm>; > - rockchip,lpddr3_odt = <LP3_ODT_240ohm>; > - rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>; > - rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>; > - rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>; > + rockchip,lpddr3_drv = <34>; > + rockchip,lpddr3_odt = <240>; > + rockchip,phy_lpddr3_ca_drv = <40>; > + rockchip,phy_lpddr3_dq_drv = <40>; > + rockchip,phy_lpddr3_odt = <240>; > rockchip,lpddr4_odt_dis_freq = <333>; > - rockchip,lpddr4_drv = <LP4_PDDS_60ohm>; > - rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>; > - rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>; > - rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>; > - rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>; > - rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>; > - rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>; > + rockchip,lpddr4_drv = <60>; > + rockchip,lpddr4_dq_odt = <40>; > + rockchip,lpddr4_ca_odt = <40>; > + rockchip,phy_lpddr4_ca_drv = <40>; > + rockchip,phy_lpddr4_ck_cs_drv = <80>; > + rockchip,phy_lpddr4_dq_drv = <80>; > + rockchip,phy_lpddr4_odt = <60>; > }; > Applied it with following minor fixup (unneeded spaces). Thanks diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt index ddde2c4f97df..ac189dd82b08 100644 --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -154,7 +154,7 @@ Following properties relate to DDR timing: driver strength. Default value is 80. - rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines - the PHY side ODT strength. Default value is 60. + the PHY side ODT strength. Default value is 60.
diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt index a41bcfef95c8..ddde2c4f97df 100644 --- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt +++ b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt @@ -79,24 +79,23 @@ Following properties relate to DDR timing: - rockchip,ddr3_drv : When the DRAM type is DDR3, this parameter defines the DRAM side driver strength in ohms. Default - value is DDR3_DS_40ohm. + value is 40. - rockchip,ddr3_odt : When the DRAM type is DDR3, this parameter defines the DRAM side ODT strength in ohms. Default value - is DDR3_ODT_120ohm. + is 120. - rockchip,phy_ddr3_ca_drv : When the DRAM type is DDR3, this parameter defines the phy side CA line (incluing command line, address line and clock line) driver strength. - Default value is PHY_DRV_ODT_40. + Default value is 40. - rockchip,phy_ddr3_dq_drv : When the DRAM type is DDR3, this parameter defines the PHY side DQ line (including DQS/DQ/DM line) - driver strength. Default value is PHY_DRV_ODT_40. + driver strength. Default value is 40. - rockchip,phy_ddr3_odt : When the DRAM type is DDR3, this parameter defines - the PHY side ODT strength. Default value is - PHY_DRV_ODT_240. + the PHY side ODT strength. Default value is 240. - rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines then ODT disable frequency in MHz (Mega Hz). @@ -106,25 +105,23 @@ Following properties relate to DDR timing: - rockchip,lpddr3_drv : When the DRAM type is LPDDR3, this parameter defines the DRAM side driver strength in ohms. Default - value is LP3_DS_34ohm. + value is 34. - rockchip,lpddr3_odt : When the DRAM type is LPDDR3, this parameter defines the DRAM side ODT strength in ohms. Default value - is LP3_ODT_240ohm. + is 240. - rockchip,phy_lpddr3_ca_drv : When the DRAM type is LPDDR3, this parameter defines the PHY side CA line (including command line, address line and clock line) driver strength. - Default value is PHY_DRV_ODT_40. + Default value is 40. - rockchip,phy_lpddr3_dq_drv : When the DRAM type is LPDDR3, this parameter defines the PHY side DQ line (including DQS/DQ/DM line) - driver strength. Default value is - PHY_DRV_ODT_40. + driver strength. Default value is 40. - rockchip,phy_lpddr3_odt : When dram type is LPDDR3, this parameter define - the phy side odt strength, default value is - PHY_DRV_ODT_240. + the phy side odt strength, default value is 240. - rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter defines the ODT disable frequency in @@ -134,32 +131,30 @@ Following properties relate to DDR timing: - rockchip,lpddr4_drv : When the DRAM type is LPDDR4, this parameter defines the DRAM side driver strength in ohms. Default - value is LP4_PDDS_60ohm. + value is 60. - rockchip,lpddr4_dq_odt : When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on DQS/DQ line strength in ohms. - Default value is LP4_DQ_ODT_40ohm. + Default value is 40. - rockchip,lpddr4_ca_odt : When the DRAM type is LPDDR4, this parameter defines the DRAM side ODT on CA line strength in ohms. - Default value is LP4_CA_ODT_40ohm. + Default value is 40. - rockchip,phy_lpddr4_ca_drv : When the DRAM type is LPDDR4, this parameter defines the PHY side CA line (including command address - line) driver strength. Default value is - PHY_DRV_ODT_40. + line) driver strength. Default value is 40. - rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines the PHY side clock line and CS line driver - strength. Default value is PHY_DRV_ODT_80. + strength. Default value is 80. - rockchip,phy_lpddr4_dq_drv : When the DRAM type is LPDDR4, this parameter defines the PHY side DQ line (including DQS/DQ/DM line) - driver strength. Default value is PHY_DRV_ODT_80. + driver strength. Default value is 80. - rockchip,phy_lpddr4_odt : When the DRAM type is LPDDR4, this parameter defines - the PHY side ODT strength. Default value is - PHY_DRV_ODT_60. + the PHY side ODT strength. Default value is 60. Example: dmc_opp_table: dmc_opp_table { @@ -195,23 +190,23 @@ Example: rockchip,phy_dll_dis_freq = <125>; rockchip,auto_pd_dis_freq = <666>; rockchip,ddr3_odt_dis_freq = <333>; - rockchip,ddr3_drv = <DDR3_DS_40ohm>; - rockchip,ddr3_odt = <DDR3_ODT_120ohm>; - rockchip,phy_ddr3_ca_drv = <PHY_DRV_ODT_40>; - rockchip,phy_ddr3_dq_drv = <PHY_DRV_ODT_40>; - rockchip,phy_ddr3_odt = <PHY_DRV_ODT_240>; + rockchip,ddr3_drv = <40>; + rockchip,ddr3_odt = <120>; + rockchip,phy_ddr3_ca_drv = <40>; + rockchip,phy_ddr3_dq_drv = <40>; + rockchip,phy_ddr3_odt = <240>; rockchip,lpddr3_odt_dis_freq = <333>; - rockchip,lpddr3_drv = <LP3_DS_34ohm>; - rockchip,lpddr3_odt = <LP3_ODT_240ohm>; - rockchip,phy_lpddr3_ca_drv = <PHY_DRV_ODT_40>; - rockchip,phy_lpddr3_dq_drv = <PHY_DRV_ODT_40>; - rockchip,phy_lpddr3_odt = <PHY_DRV_ODT_240>; + rockchip,lpddr3_drv = <34>; + rockchip,lpddr3_odt = <240>; + rockchip,phy_lpddr3_ca_drv = <40>; + rockchip,phy_lpddr3_dq_drv = <40>; + rockchip,phy_lpddr3_odt = <240>; rockchip,lpddr4_odt_dis_freq = <333>; - rockchip,lpddr4_drv = <LP4_PDDS_60ohm>; - rockchip,lpddr4_dq_odt = <LP4_DQ_ODT_40ohm>; - rockchip,lpddr4_ca_odt = <LP4_CA_ODT_40ohm>; - rockchip,phy_lpddr4_ca_drv = <PHY_DRV_ODT_40>; - rockchip,phy_lpddr4_ck_cs_drv = <PHY_DRV_ODT_80>; - rockchip,phy_lpddr4_dq_drv = <PHY_DRV_ODT_80>; - rockchip,phy_lpddr4_odt = <PHY_DRV_ODT_60>; + rockchip,lpddr4_drv = <60>; + rockchip,lpddr4_dq_odt = <40>; + rockchip,lpddr4_ca_odt = <40>; + rockchip,phy_lpddr4_ca_drv = <40>; + rockchip,phy_lpddr4_ck_cs_drv = <80>; + rockchip,phy_lpddr4_dq_drv = <80>; + rockchip,phy_lpddr4_odt = <60>; };