| Message ID | 20210310161924.22256-4-a-govindraju@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | J7200: Add support for GPIO and higher speed modes in MMCSD subsystems | expand |
Hi, On 10/03/21 9:49 pm, Aswath Govindraju wrote: > The following speed modes are now supported in J7200 SoC, > - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. > - UHS-I speed modes in MMCSD1 subsystem [1]. > > Add support for UHS-I modes by adding voltage regulator device tree nodes > and corresponding pinmux details, to power cycle and voltage switch cards. > Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 > device tree nodes. > > Also update the delay values for various speed modes supported, based on > the latest J7200 datasheet[2] nit: Better to mention the datasheet version (as it's not latest anymore). > > [1] - section 12.3.6.1.1 MMCSD Features, in > https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf > > [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf Er.. this link is already broken. Thanks Kishon > > Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> > --- > .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++ > arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++- > 2 files changed, 54 insertions(+), 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > index b493f939b09a..6f90c3b1cf45 100644 > --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts > @@ -16,6 +16,29 @@ > stdout-path = "serial2:115200n8"; > bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; > }; > + > + vdd_mmc1: fixedregulator-sd { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_mmc1"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + enable-active-high; > + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; > + }; > + > + vdd_sd_dv: gpio-regulator-vdd-sd-dv { > + compatible = "regulator-gpio"; > + regulator-name = "vdd_sd_dv"; > + pinctrl-names = "default"; > + pinctrl-0 = <&vdd_sd_dv_pins_default>; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; > + states = <1800000 0x0 > + 3300000 0x1>; > + }; > }; > > &wkup_pmx0 { > @@ -45,6 +68,13 @@ > }; > > &main_pmx0 { > + main_i2c0_pins_default: main-i2c0-pins-default { > + pinctrl-single,pins = < > + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ > + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ > + >; > + }; > + > main_i2c1_pins_default: main-i2c1-pins-default { > pinctrl-single,pins = < > J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */ > @@ -70,6 +100,12 @@ > J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ > >; > }; > + > + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default { > + pinctrl-single,pins = < > + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ > + >; > + }; > }; > > &wkup_uart0 { > @@ -157,6 +193,10 @@ > }; > > &main_i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&main_i2c0_pins_default>; > + clock-frequency = <400000>; > + > exp1: gpio@20 { > compatible = "ti,tca6416"; > reg = <0x20>; > @@ -206,6 +246,8 @@ > /* SD card */ > pinctrl-0 = <&main_mmc1_pins_default>; > pinctrl-names = "default"; > + vmmc-supply = <&vdd_mmc1>; > + vqmmc-supply = <&vdd_sd_dv>; > ti,driver-strength-ohm = <50>; > disable-wp; > }; > diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > index e60650a62b14..f86c493a44f1 100644 > --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > @@ -512,11 +512,16 @@ > ti,otap-del-sel-mmc-hs = <0x0>; > ti,otap-del-sel-ddr52 = <0x6>; > ti,otap-del-sel-hs200 = <0x8>; > - ti,otap-del-sel-hs400 = <0x0>; > + ti,otap-del-sel-hs400 = <0x5>; > + ti,itap-del-sel-legacy = <0x10>; > + ti,itap-del-sel-mmc-hs = <0xa>; > ti,strobe-sel = <0x77>; > + ti,clkbuf-sel = <0x7>; > ti,trm-icp = <0x8>; > bus-width = <8>; > mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + mmc-hs400-1_8v; > dma-coherent; > }; > > @@ -534,7 +539,12 @@ > ti,otap-del-sel-sdr50 = <0xc>; > ti,otap-del-sel-sdr104 = <0x5>; > ti,otap-del-sel-ddr50 = <0xc>; > - no-1-8-v; > + ti,itap-del-sel-legacy = <0x0>; > + ti,itap-del-sel-sd-hs = <0x0>; > + ti,itap-del-sel-sdr12 = <0x0>; > + ti,itap-del-sel-sdr25 = <0x0>; > + ti,clkbuf-sel = <0x7>; > + ti,trm-icp = <0x8>; > dma-coherent; > }; > >
Hi Kishon, On 18/03/21 8:45 pm, Kishon Vijay Abraham I wrote: > Hi, > > On 10/03/21 9:49 pm, Aswath Govindraju wrote: >> The following speed modes are now supported in J7200 SoC, >> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. >> - UHS-I speed modes in MMCSD1 subsystem [1]. >> >> Add support for UHS-I modes by adding voltage regulator device tree nodes >> and corresponding pinmux details, to power cycle and voltage switch cards. >> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 >> device tree nodes. >> >> Also update the delay values for various speed modes supported, based on >> the latest J7200 datasheet[2] > > nit: Better to mention the datasheet version (as it's not latest anymore). >> >> [1] - section 12.3.6.1.1 MMCSD Features, in >> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf >> >> [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf > > Er.. this link is already broken. > Sorry, fixed this and added the version information for references in the respin(v6) of this series. Thank you for the comments. Regards, Aswath > Thanks > Kishon >> >> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> >> --- >> .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++ >> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++- >> 2 files changed, 54 insertions(+), 2 deletions(-) >> >> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> index b493f939b09a..6f90c3b1cf45 100644 >> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts >> @@ -16,6 +16,29 @@ >> stdout-path = "serial2:115200n8"; >> bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; >> }; >> + >> + vdd_mmc1: fixedregulator-sd { >> + compatible = "regulator-fixed"; >> + regulator-name = "vdd_mmc1"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + enable-active-high; >> + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; >> + }; >> + >> + vdd_sd_dv: gpio-regulator-vdd-sd-dv { >> + compatible = "regulator-gpio"; >> + regulator-name = "vdd_sd_dv"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&vdd_sd_dv_pins_default>; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; >> + states = <1800000 0x0 >> + 3300000 0x1>; >> + }; >> }; >> >> &wkup_pmx0 { >> @@ -45,6 +68,13 @@ >> }; >> >> &main_pmx0 { >> + main_i2c0_pins_default: main-i2c0-pins-default { >> + pinctrl-single,pins = < >> + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ >> + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >> + >; >> + }; >> + >> main_i2c1_pins_default: main-i2c1-pins-default { >> pinctrl-single,pins = < >> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */ >> @@ -70,6 +100,12 @@ >> J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ >> >; >> }; >> + >> + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default { >> + pinctrl-single,pins = < >> + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ >> + >; >> + }; >> }; >> >> &wkup_uart0 { >> @@ -157,6 +193,10 @@ >> }; >> >> &main_i2c0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&main_i2c0_pins_default>; >> + clock-frequency = <400000>; >> + >> exp1: gpio@20 { >> compatible = "ti,tca6416"; >> reg = <0x20>; >> @@ -206,6 +246,8 @@ >> /* SD card */ >> pinctrl-0 = <&main_mmc1_pins_default>; >> pinctrl-names = "default"; >> + vmmc-supply = <&vdd_mmc1>; >> + vqmmc-supply = <&vdd_sd_dv>; >> ti,driver-strength-ohm = <50>; >> disable-wp; >> }; >> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> index e60650a62b14..f86c493a44f1 100644 >> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> @@ -512,11 +512,16 @@ >> ti,otap-del-sel-mmc-hs = <0x0>; >> ti,otap-del-sel-ddr52 = <0x6>; >> ti,otap-del-sel-hs200 = <0x8>; >> - ti,otap-del-sel-hs400 = <0x0>; >> + ti,otap-del-sel-hs400 = <0x5>; >> + ti,itap-del-sel-legacy = <0x10>; >> + ti,itap-del-sel-mmc-hs = <0xa>; >> ti,strobe-sel = <0x77>; >> + ti,clkbuf-sel = <0x7>; >> ti,trm-icp = <0x8>; >> bus-width = <8>; >> mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + mmc-hs400-1_8v; >> dma-coherent; >> }; >> >> @@ -534,7 +539,12 @@ >> ti,otap-del-sel-sdr50 = <0xc>; >> ti,otap-del-sel-sdr104 = <0x5>; >> ti,otap-del-sel-ddr50 = <0xc>; >> - no-1-8-v; >> + ti,itap-del-sel-legacy = <0x0>; >> + ti,itap-del-sel-sd-hs = <0x0>; >> + ti,itap-del-sel-sdr12 = <0x0>; >> + ti,itap-del-sel-sdr25 = <0x0>; >> + ti,clkbuf-sel = <0x7>; >> + ti,trm-icp = <0x8>; >> dma-coherent; >> }; >> >>
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index b493f939b09a..6f90c3b1cf45 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -16,6 +16,29 @@ stdout-path = "serial2:115200n8"; bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; }; + + vdd_mmc1: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; + }; + + vdd_sd_dv: gpio-regulator-vdd-sd-dv { + compatible = "regulator-gpio"; + regulator-name = "vdd_sd_dv"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_sd_dv_pins_default>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0 + 3300000 0x1>; + }; }; &wkup_pmx0 { @@ -45,6 +68,13 @@ }; &main_pmx0 { + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */ @@ -70,6 +100,12 @@ J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ >; }; + + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ + >; + }; }; &wkup_uart0 { @@ -157,6 +193,10 @@ }; &main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + exp1: gpio@20 { compatible = "ti,tca6416"; reg = <0x20>; @@ -206,6 +246,8 @@ /* SD card */ pinctrl-0 = <&main_mmc1_pins_default>; pinctrl-names = "default"; + vmmc-supply = <&vdd_mmc1>; + vqmmc-supply = <&vdd_sd_dv>; ti,driver-strength-ohm = <50>; disable-wp; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index e60650a62b14..f86c493a44f1 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -512,11 +512,16 @@ ti,otap-del-sel-mmc-hs = <0x0>; ti,otap-del-sel-ddr52 = <0x6>; ti,otap-del-sel-hs200 = <0x8>; - ti,otap-del-sel-hs400 = <0x0>; + ti,otap-del-sel-hs400 = <0x5>; + ti,itap-del-sel-legacy = <0x10>; + ti,itap-del-sel-mmc-hs = <0xa>; ti,strobe-sel = <0x77>; + ti,clkbuf-sel = <0x7>; ti,trm-icp = <0x8>; bus-width = <8>; mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; dma-coherent; }; @@ -534,7 +539,12 @@ ti,otap-del-sel-sdr50 = <0xc>; ti,otap-del-sel-sdr104 = <0x5>; ti,otap-del-sel-ddr50 = <0xc>; - no-1-8-v; + ti,itap-del-sel-legacy = <0x0>; + ti,itap-del-sel-sd-hs = <0x0>; + ti,itap-del-sel-sdr12 = <0x0>; + ti,itap-del-sel-sdr25 = <0x0>; + ti,clkbuf-sel = <0x7>; + ti,trm-icp = <0x8>; dma-coherent; };
The following speed modes are now supported in J7200 SoC, - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. - UHS-I speed modes in MMCSD1 subsystem [1]. Add support for UHS-I modes by adding voltage regulator device tree nodes and corresponding pinmux details, to power cycle and voltage switch cards. Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 device tree nodes. Also update the delay values for various speed modes supported, based on the latest J7200 datasheet[2] [1] - section 12.3.6.1.1 MMCSD Features, in https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf [2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> --- .../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++- 2 files changed, 54 insertions(+), 2 deletions(-)