@@ -34,6 +34,19 @@ power {
};
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ ddc-i2c-bus = <&ddc_i2c_bus>;
+ label = "hdmi";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <<8912_out>;
+ };
+ };
+ };
+
reg_usb_otg_vbus: regulator-usb-otg-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -81,6 +94,9 @@ reg_vref_5v: regulator-vref-5v {
};
};
+&dphy {
+ status = "okay";
+};
&fec1 {
pinctrl-names = "default";
@@ -193,6 +209,105 @@ rtc@68 {
};
};
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ pca9546: i2cmux9546@70 {
+ compatible = "nxp,pca9546";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c4@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+
+ hdmi-bridge@48 {
+ compatible = "lontium,lt8912b";
+ reg = <0x48> ;
+ reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_out_in: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&mipi_dsi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lt8912_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+ };
+
+ ddc_i2c_bus: i2c4@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ };
+
+ i2c4@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+
+ max7323: max7323@68 {
+ compatible = "maxim,max7323";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_max7323>;
+ gpio-controller;
+ reg = <0x68>;
+ #gpio-cells = <2>;
+ };
+ };
+ };
+};
+
+&gpio3 {
+ max7323_intterupt {
+ gpio-hog;
+ gpios = <15 0>;
+ input;
+ };
+};
+
+&lcdif {
+ status = "okay";
+};
+
+&mipi_dsi {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mipi_dsi_out: endpoint {
+ remote-endpoint = <&hdmi_out_in>;
+ };
+ };
+ };
+};
+
&uart1 { /* console */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
@@ -368,6 +483,19 @@ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x49
>;
};
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_max7323: max7323grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
+ >;
+ };
+
pinctrl_reg_arm_dram: reg-arm-dramgrp {
fsl,pins = <
MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x16
Add support of the lt8912b in the DTB. This adds the support of the DB_DSIHD daugther board from Boundary Devices. Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com> --- .../boot/dts/freescale/imx8mq-nitrogen.dts | 128 ++++++++++++++++++ 1 file changed, 128 insertions(+)