diff mbox series

[v4,2/5] ARM: dts: sun8i: r40: add pinmux settings for MMC3 and UARTs 2, 4, 5&7

Message ID 20210407111428.3755684-3-i.uvarov@cognitivepilot.com (mailing list archive)
State New, archived
Headers show
Series add devicetree for Forlinx FETA40i-C & OKA40i-C | expand

Commit Message

Ivan Uvarov April 7, 2021, 11:14 a.m. UTC 
The Forlinx OKA40i-C devboard makes use of UARTs 0,2,3,4,5 and 7 of the R40
SoC, of which UART 0 is connected to an RS232 converter, UART 5 routed to
an RS485 converter, and the rest broken out directly via labeled headers.
The board also contains a micro-SD slot connected to SDC3.

This patch adds settings to R40's pinmux node for MMC3 and those UARTs that
were not already mapped, which would allow us to make use of all available
UARTs and the micro-SD slot on this board in a further patch.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>

 1 file changed, 41 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index 0b257a0779..9ad4f0129c 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -357,6 +357,8 @@  mmc3: mmc@1c12000 {
 			clock-names = "ahb", "mmc";
 			resets = <&ccu RST_BUS_MMC3>;
 			reset-names = "ahb";
+			pinctrl-0 = <&mmc3_pins>;
+			pinctrl-names = "default";
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -601,6 +603,15 @@  mmc2_pins: mmc2-pins {
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			mmc3_pins: mmc3-pins {
+				pins = "PI4", "PI5", "PI6",
+				       "PI7", "PI8", "PI9";
+				function = "mmc3";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			/omit-if-no-ref/
 			spi0_pc_pins: spi0-pc-pins {
 				pins = "PC0", "PC1", "PC2";
@@ -637,6 +648,18 @@  uart0_pb_pins: uart0-pb-pins {
 				function = "uart0";
 			};
 
+			/omit-if-no-ref/
+			uart2_pi_pins: uart2-pi-pins {
+				pins = "PI18", "PI19";
+				function = "uart2";
+			};
+
+			/omit-if-no-ref/
+			uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins{
+				pins = "PI16", "PI17";
+				function = "uart2";
+			};
+
 			/omit-if-no-ref/
 			uart3_pg_pins: uart3-pg-pins {
 				pins = "PG6", "PG7";
@@ -648,6 +671,24 @@  uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
 				pins = "PG8", "PG9";
 				function = "uart3";
 			};
+
+			/omit-if-no-ref/
+			uart4_pg_pins: uart4-pg-pins {
+				pins = "PG10", "PG11";
+				function = "uart4";
+			};
+
+			/omit-if-no-ref/
+			uart5_ph_pins: uart5-ph-pins {
+				pins = "PH6", "PH7";
+				function = "uart5";
+			};
+
+			/omit-if-no-ref/
+			uart7_pi_pins: uart7-pi-pins {
+				pins = "PI20", "PI21";
+				function = "uart7";
+			};
 		};
 
 		wdt: watchdog@1c20c90 {