diff mbox series

[v2,3/3] arm64: dts: imx8mq: add support for MNT Reform2

Message ID 20210510185931.104780-3-l.stach@pengutronix.de (mailing list archive)
State New, archived
Headers show
Series [v2,1/3] arm64: dts: imx8mq: add Nitrogen8 SoM | expand

Commit Message

Lucas Stach May 10, 2021, 6:59 p.m. UTC 
From: Lucas Stach <dev@lynxeye.de>

This adds a basic devicetree for the MNT Reform2 DIY laptop. Not all
of the board periperals are enabled yet, as some of them still require
kernel patches to work properly. The nodes for those peripherals will
be added as soon as the required patches are upstream.

The following has been tested to work:
- UART console
- SD card
- eMMC
- Gigabit Ethernet
- USB (internal Keyboard, Mouse, external ports)
- M.2 PCIe port

Co-developed-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Lucas Stach <dev@lynxeye.de>
---
v2: Fix checkpatch complaints.
---
 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../boot/dts/freescale/imx8mq-mnt-reform2.dts | 164 ++++++++++++++++++
 3 files changed, 166 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts

Comments

Fabio Estevam May 11, 2021, 11:46 a.m. UTC | #1 
On Mon, May 10, 2021 at 4:00 PM Lucas Stach <l.stach@pengutronix.de> wrote:


> +&i2c3 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c3>;
> +       status = "okay";
> +
> +       pcf8523: pcf8523@68 {

Just a nit: node names should be generic: rtc@68

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rob Herring May 11, 2021, 7:04 p.m. UTC | #2 
On Mon, 10 May 2021 20:59:31 +0200, Lucas Stach wrote:
> From: Lucas Stach <dev@lynxeye.de>
> 
> This adds a basic devicetree for the MNT Reform2 DIY laptop. Not all
> of the board periperals are enabled yet, as some of them still require
> kernel patches to work properly. The nodes for those peripherals will
> be added as soon as the required patches are upstream.
> 
> The following has been tested to work:
> - UART console
> - SD card
> - eMMC
> - Gigabit Ethernet
> - USB (internal Keyboard, Mouse, external ports)
> - M.2 PCIe port
> 
> Co-developed-by: Lukas F. Hartmann <lukas@mntre.com>
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> ---
> v2: Fix checkpatch complaints.
> ---
>  .../devicetree/bindings/arm/fsl.yaml          |   1 +
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx8mq-mnt-reform2.dts | 164 ++++++++++++++++++
>  3 files changed, 166 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
> 

Reviewed-by: Rob Herring <robh@kernel.org>
Shawn Guo May 23, 2021, 3:21 a.m. UTC | #3 
On Mon, May 10, 2021 at 08:59:31PM +0200, Lucas Stach wrote:
> From: Lucas Stach <dev@lynxeye.de>
> 
> This adds a basic devicetree for the MNT Reform2 DIY laptop. Not all
> of the board periperals are enabled yet, as some of them still require
> kernel patches to work properly. The nodes for those peripherals will
> be added as soon as the required patches are upstream.
> 
> The following has been tested to work:
> - UART console
> - SD card
> - eMMC
> - Gigabit Ethernet
> - USB (internal Keyboard, Mouse, external ports)
> - M.2 PCIe port
> 
> Co-developed-by: Lukas F. Hartmann <lukas@mntre.com>
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> ---
> v2: Fix checkpatch complaints.
> ---
>  .../devicetree/bindings/arm/fsl.yaml          |   1 +

Bindings goes to separate patch.

>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx8mq-mnt-reform2.dts | 164 ++++++++++++++++++
>  3 files changed, 166 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 15519cc2d2c0..fd208c7e49ae 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -737,6 +737,7 @@ properties:
>                - purism,librem5-devkit     # Purism Librem5 devkit
>                - solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse
>                - technexion,pico-pi-imx8m  # TechNexion PICO-PI-8M evk
> +              - mntre,reform2             # MNT Reform2 Laptop

Break order.

>            - const: fsl,imx8mq
>  
>        - description: Purism Librem5 phones
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 44890d56c194..e45c8f9c8912 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -54,6 +54,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mq-mnt-reform2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
> new file mode 100644
> index 000000000000..104a236c9609
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
> @@ -0,0 +1,164 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/*
> + * Copyright 2019-2021 MNT Research GmbH
> + * Copyright 2021 Lucas Stach <dev@lynxeye.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mq-nitrogen-som.dtsi"
> +
> +/ {
> +	model = "MNT Reform 2";
> +	compatible = "mntre,reform2", "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
> +
> +	pcie1_refclk: clock-pcie1-refclk {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <100000000>;
> +	};
> +
> +	reg_main_5v: regulator-main-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	reg_main_3v3: regulator-main-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	reg_main_usb: regulator-main-usb {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&reg_main_5v>;
> +	};
> +};
> +
> +&fec1 {
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	status = "okay";
> +
> +	pcf8523: pcf8523@68 {
> +		compatible = "nxp,pcf8523";
> +		reg = <0x68>;
> +	};
> +};
> +
> +&pcie1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pcie1>;
> +	reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>;
> +	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
> +		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
> +		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
> +		 <&pcie1_refclk>;
> +	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
> +	status = "okay";
> +};
> +
> +&reg_1p8v {
> +	vin-supply = <&reg_main_5v>;
> +};
> +
> +&reg_snvs {
> +	vin-supply = <&reg_main_5v>;
> +};
> +
> +&reg_arm_dram {
> +	vin-supply = <&reg_main_5v>;
> +};
> +
> +&reg_dram_1p1v {
> +	vin-supply = <&reg_main_5v>;
> +};
> +
> +&reg_soc_gpu_vpu {
> +	vin-supply = <&reg_main_5v>;
> +};
> +
> +&snvs_rtc {
> +	status = "disabled";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +&usb3_phy0 {
> +	vbus-supply = <&reg_main_usb>;
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	vbus-supply = <&reg_main_usb>;
> +	status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> +	status = "okay";
> +	dr_mode = "host";

End property list with 'status' please.

> +};
> +
> +&usb_dwc3_1 {
> +	status = "okay";
> +	dr_mode = "host";

Ditto

Shawn

> +};
> +
> +&usdhc2 {
> +	assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
> +	assigned-clock-rates = <200000000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	vqmmc-supply = <&reg_main_3v3>;
> +	vmmc-supply = <&reg_main_3v3>;
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x4000007f
> +			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x4000007f
> +		>;
> +	};
> +
> +	pinctrl_pcie1: pcie1grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x16
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x45
> +			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
> +			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
> +			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
> +			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
> +		>;
> +	};
> +};
> -- 
> 2.31.1
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 15519cc2d2c0..fd208c7e49ae 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -737,6 +737,7 @@  properties:
               - purism,librem5-devkit     # Purism Librem5 devkit
               - solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse
               - technexion,pico-pi-imx8m  # TechNexion PICO-PI-8M evk
+              - mntre,reform2             # MNT Reform2 Laptop
           - const: fsl,imx8mq
 
       - description: Purism Librem5 phones
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 44890d56c194..e45c8f9c8912 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -54,6 +54,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-mnt-reform2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
new file mode 100644
index 000000000000..104a236c9609
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
@@ -0,0 +1,164 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/*
+ * Copyright 2019-2021 MNT Research GmbH
+ * Copyright 2021 Lucas Stach <dev@lynxeye.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mq-nitrogen-som.dtsi"
+
+/ {
+	model = "MNT Reform 2";
+	compatible = "mntre,reform2", "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
+
+	pcie1_refclk: clock-pcie1-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_main_5v: regulator-main-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_main_3v3: regulator-main-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_main_usb: regulator-main-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_main_5v>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pcf8523: pcf8523@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie1>;
+	reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
+		 <&pcie1_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	status = "okay";
+};
+
+&reg_1p8v {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_snvs {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_arm_dram {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_dram_1p1v {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_soc_gpu_vpu {
+	vin-supply = <&reg_main_5v>;
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_main_usb>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_main_usb>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vqmmc-supply = <&reg_main_3v3>;
+	vmmc-supply = <&reg_main_3v3>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_pcie1: pcie1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x16
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x45
+			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+		>;
+	};
+};