@@ -106,4 +106,31 @@ partitions {
fis-index-block = <0x3f>;
};
};
+
+ soc {
+ pci@c0000000 {
+ status = "ok";
+
+ /*
+ * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant
+ * We have slots (IDSEL) 1, 2 and 3.
+ */
+ interrupt-map =
+ /* IDSEL 1 */
+ <0x0800 0 0 1 &gpio0 11 3>, /* INT A on slot 1 is irq 11 */
+ <0x0800 0 0 2 &gpio0 10 3>, /* INT B on slot 1 is irq 10 */
+ <0x0800 0 0 3 &gpio0 9 3>, /* INT C on slot 1 is irq 9 */
+ <0x0800 0 0 4 &gpio0 8 3>, /* INT D on slot 1 is irq 8 */
+ /* IDSEL 2 */
+ <0x1000 0 0 1 &gpio0 10 3>, /* INT A on slot 2 is irq 10 */
+ <0x1000 0 0 2 &gpio0 9 3>, /* INT B on slot 2 is irq 9 */
+ <0x1000 0 0 3 &gpio0 11 3>, /* INT C on slot 2 is irq 11 */
+ <0x1000 0 0 4 &gpio0 8 3>, /* INT D on slot 2 is irq 8 */
+ /* IDSEL 3 */
+ <0x1800 0 0 1 &gpio0 9 3>, /* INT A on slot 3 is irq 9 */
+ <0x1800 0 0 2 &gpio0 11 3>, /* INT B on slot 3 is irq 11 */
+ <0x1800 0 0 3 &gpio0 10 3>, /* INT C on slot 3 is irq 10 */
+ <0x1800 0 0 4 &gpio0 8 3>; /* INT D on slot 3 is irq 8 */
+ };
+ };
};
@@ -7,6 +7,10 @@
/ {
soc {
+ pci@c0000000 {
+ compatible = "intel,ixp42x-pci";
+ };
+
interrupt-controller@c8003000 {
compatible = "intel,ixp42x-interrupt";
};
@@ -91,4 +91,50 @@ partitions {
fis-index-block = <0xff>;
};
};
+
+ soc {
+ pci@c0000000 {
+ status = "ok";
+
+ /*
+ * In the boardfile for the Cambria from OpenWRT the interrupts
+ * are assigned one per IDSEL, so all 4 interrupts from IDSEL
+ * 1 are connected to IRQ 11, all 4 interrupts from IDSEL 2
+ * connected to IRQ 10 etc. I find this highly unlikely so I
+ * have instead assumed that they are rotated (swizzled) like
+ * this with 11, 10, 9, 8 for the 4 pins on IDSEL 1 etc.
+ */
+ interrupt-map =
+ /* IDSEL 1 */
+ <0x0800 0 0 1 &gpio0 11 3>, /* INT A on slot 1 is irq 11 */
+ <0x0800 0 0 2 &gpio0 10 3>, /* INT B on slot 1 is irq 10 */
+ <0x0800 0 0 3 &gpio0 9 3>, /* INT C on slot 1 is irq 9 */
+ <0x0800 0 0 4 &gpio0 8 3>, /* INT D on slot 1 is irq 8 */
+ /* IDSEL 2 */
+ <0x1000 0 0 1 &gpio0 10 3>, /* INT A on slot 2 is irq 10 */
+ <0x1000 0 0 2 &gpio0 9 3>, /* INT B on slot 2 is irq 9 */
+ <0x1000 0 0 3 &gpio0 8 3>, /* INT C on slot 2 is irq 8 */
+ <0x1000 0 0 4 &gpio0 11 3>, /* INT D on slot 2 is irq 11 */
+ /* IDSEL 3 */
+ <0x1800 0 0 1 &gpio0 9 3>, /* INT A on slot 3 is irq 9 */
+ <0x1800 0 0 2 &gpio0 8 3>, /* INT B on slot 3 is irq 8 */
+ <0x1800 0 0 3 &gpio0 11 3>, /* INT C on slot 3 is irq 11 */
+ <0x1800 0 0 4 &gpio0 10 3>, /* INT D on slot 3 is irq 10 */
+ /* IDSEL 4 */
+ <0x2000 0 0 1 &gpio0 8 3>, /* INT A on slot 3 is irq 8 */
+ <0x2000 0 0 2 &gpio0 11 3>, /* INT B on slot 3 is irq 11 */
+ <0x2000 0 0 3 &gpio0 10 3>, /* INT C on slot 3 is irq 10 */
+ <0x2000 0 0 4 &gpio0 9 3>, /* INT D on slot 3 is irq 9 */
+ /* IDSEL 6 */
+ <0x3000 0 0 1 &gpio0 10 3>, /* INT A on slot 3 is irq 10 */
+ <0x3000 0 0 2 &gpio0 9 3>, /* INT B on slot 3 is irq 9 */
+ <0x3000 0 0 3 &gpio0 8 3>, /* INT C on slot 3 is irq 8 */
+ <0x3000 0 0 4 &gpio0 11 3>, /* INT D on slot 3 is irq 11 */
+ /* IDSEL 15 */
+ <0x7800 0 0 1 &gpio0 8 3>, /* INT A on slot 3 is irq 8 */
+ <0x7800 0 0 2 &gpio0 11 3>, /* INT B on slot 3 is irq 11 */
+ <0x7800 0 0 3 &gpio0 10 3>, /* INT C on slot 3 is irq 10 */
+ <0x7800 0 0 4 &gpio0 9 3>; /* INT D on slot 3 is irq 9 */
+ };
+ };
};
@@ -8,6 +8,10 @@
/ {
soc {
+ pci@c0000000 {
+ compatible = "intel,ixp43x-pci";
+ };
+
interrupt-controller@c8003000 {
compatible = "intel,ixp43x-interrupt";
};
@@ -20,6 +20,42 @@ qmgr: queue-manager@60000000 {
interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>;
};
+ pci@c0000000 {
+ compatible = "intel,ixp43x-pci";
+ reg = <0xc0000000 0x1000>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>,
+ <9 IRQ_TYPE_LEVEL_HIGH>,
+ <10 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0x00 0xff>;
+ status = "disabled";
+
+ ranges =
+ /*
+ * 64MB 32bit non-prefetchable memory 0x48000000-0x4bffffff
+ * done in 4 chunks of 16MB each.
+ */
+ <0x02000000 0 0x48000000 0x48000000 0 0x04000000>,
+ /* 64KB I/O space at 0x4c000000 */
+ <0x01000000 0 0x00000000 0x4c000000 0 0x00010000>;
+
+ /*
+ * This needs to map to the start of physical memory so
+ * PCI devices can see all (hopefully) memory. This is done
+ * using 4 1:1 16MB windows, so the RAM should not be more than
+ * 64 MB for this to work. If your memory is anywhere else
+ * than at 0x0 you need to alter this.
+ */
+ dma-ranges =
+ <0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ /* Each unique DTS using PCI must specify the swizzling */
+ };
+
uart0: serial@c8000000 {
compatible = "intel,xscale-uart";
reg = <0xc8000000 0x1000>;
This adds a basic PCI host definition to the base device tree for IXP4xx and then further details it in the 42x and 43x device tree include, also the specific target devices NSLU2 and GW2358 get proper PCI swizzling defined. Cc: Zoltan HERPAI <wigyori@uid0.hu> Cc: Raylynn Knight <rayknight@me.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- .../boot/dts/intel-ixp42x-linksys-nslu2.dts | 27 +++++++++++ arch/arm/boot/dts/intel-ixp42x.dtsi | 4 ++ .../dts/intel-ixp43x-gateworks-gw2358.dts | 46 +++++++++++++++++++ arch/arm/boot/dts/intel-ixp43x.dtsi | 4 ++ arch/arm/boot/dts/intel-ixp4xx.dtsi | 36 +++++++++++++++ 5 files changed, 117 insertions(+)