Message ID | 20210804130625.15449-4-michael.riesch@wolfvision.net (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | arm64: dts: rockchip: rk3568-evb1-v10: add sd card support | expand |
Hi Michael, Missing commit message. On 8/4/21 3:06 PM, Michael Riesch wrote: > Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net> > --- > .../boot/dts/rockchip/rk3568-evb1-v10.dts | 206 ++++++++++++++++++ > 1 file changed, 206 insertions(+) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts > index 65e536c78d2e..f682144a1892 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts > +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts > @@ -104,6 +104,203 @@ > status = "okay"; > }; > > +&i2c0 { > + status = "okay"; > + > + rk809: pmic@20 { > + compatible = "rockchip,rk809"; > + reg = <0x20>; > + interrupt-parent = <&gpio0>; > + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; > + #clock-cells = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pmic_int>; pinctrl-names below pinctrl-0 like the rest of rk356x.dtsi > + rockchip,system-power-controller; > + wakeup-source; > + > + vcc1-supply = <&vcc3v3_sys>; > + vcc2-supply = <&vcc3v3_sys>; > + vcc3-supply = <&vcc3v3_sys>; > + vcc4-supply = <&vcc3v3_sys>; > + vcc5-supply = <&vcc3v3_sys>; > + vcc6-supply = <&vcc3v3_sys>; > + vcc7-supply = <&vcc3v3_sys>; > + vcc8-supply = <&vcc3v3_sys>; > + vcc9-supply = <&vcc3v3_sys>; > + > + regulators { > + vdd_logic: DCDC_REG1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1350000>; > + regulator-init-microvolt = <900000>; > + regulator-ramp-delay = <6001>; > + regulator-initial-mode = <0x2>; > + regulator-name = "vdd_logic"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdd_gpu: DCDC_REG2 { > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1350000>; > + regulator-init-microvolt = <900000>; > + regulator-ramp-delay = <6001>; > + regulator-initial-mode = <0x2>; > + regulator-name = "vdd_gpu"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_ddr: DCDC_REG3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-initial-mode = <0x2>; > + regulator-name = "vcc_ddr"; > + regulator-state-mem { > + regulator-on-in-suspend; > + }; > + }; > + > + vdd_npu: DCDC_REG4 { > + regulator-min-microvolt = <500000>; > + regulator-max-microvolt = <1350000>; Exception to the sort rule: 1: regulator-min-microvolt above regulator-max-microvolt 2: regulator-name above all other regulator properties. The rest in alphabetical order. Fix them all. > + regulator-init-microvolt = <900000>; > + regulator-ramp-delay = <6001>; > + regulator-initial-mode = <0x2>; > + regulator-name = "vdd_npu"; Add empty line between properties and a node. > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_1v8: DCDC_REG5 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcc_1v8"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdda0v9_image: LDO_REG1 { > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-name = "vdda0v9_image"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdda_0v9: LDO_REG2 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-name = "vdda_0v9"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vdda0v9_pmu: LDO_REG3 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + regulator-name = "vdda0v9_pmu"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <900000>; > + }; > + }; > + > + vccio_acodec: LDO_REG4 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vccio_acodec"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vccio_sd: LDO_REG5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vccio_sd"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc3v3_pmu: LDO_REG6 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "vcc3v3_pmu"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <3300000>; > + }; > + }; > + > + vcca_1v8: LDO_REG7 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcca_1v8"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcca1v8_pmu: LDO_REG8 { > + regulator-always-on; > + regulator-boot-on; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcca1v8_pmu"; > + regulator-state-mem { > + regulator-on-in-suspend; > + regulator-suspend-microvolt = <1800000>; > + }; > + }; > + > + vcca1v8_image: LDO_REG9 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-name = "vcca1v8_image"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc_3v3: SWITCH_REG1 { > + regulator-always-on; > + regulator-boot-on; > + regulator-name = "vcc_3v3"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + > + vcc3v3_sd: SWITCH_REG2 { > + regulator-name = "vcc3v3_sd"; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > + }; > + }; > + }; > +}; > + > &mdio0 { > rgmii_phy0: ethernet-phy@0 { > compatible = "ethernet-phy-ieee802.3-c22"; > @@ -124,6 +321,15 @@ > }; > }; > > +&pinctrl { > + pmic { > + pmic_int: pmic_int { > + rockchip,pins = > + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; > + }; > + }; > +}; > + > &sdhci { > bus-width = <8>; > max-frequency = <200000000>; >
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts index 65e536c78d2e..f682144a1892 100644 --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts @@ -104,6 +104,203 @@ status = "okay"; }; +&i2c0 { + status = "okay"; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc3v3_sys>; + vcc2-supply = <&vcc3v3_sys>; + vcc3-supply = <&vcc3v3_sys>; + vcc4-supply = <&vcc3v3_sys>; + vcc5-supply = <&vcc3v3_sys>; + vcc6-supply = <&vcc3v3_sys>; + vcc7-supply = <&vcc3v3_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc3v3_sys>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_logic"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_npu: DCDC_REG4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_npu"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: DCDC_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_image: LDO_REG1 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda0v9_image"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda_0v9"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda0v9_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_acodec"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca_1v8: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca_1v8"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pmu: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca1v8_image: LDO_REG9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_image"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_3v3: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_3v3"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_sd: SWITCH_REG2 { + regulator-name = "vcc3v3_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + &mdio0 { rgmii_phy0: ethernet-phy@0 { compatible = "ethernet-phy-ieee802.3-c22"; @@ -124,6 +321,15 @@ }; }; +&pinctrl { + pmic { + pmic_int: pmic_int { + rockchip,pins = + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + &sdhci { bus-width = <8>; max-frequency = <200000000>;
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net> --- .../boot/dts/rockchip/rk3568-evb1-v10.dts | 206 ++++++++++++++++++ 1 file changed, 206 insertions(+)