| Message ID | 20211008205313.69016-1-robert.marko@sartura.hr (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v6] arm64: dts: marvell: add Globalscale MOCHAbin | expand |
Hi Robert, > Globalscale MOCHAbin is a Armada 7040 based development board. > > Specifications: > * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz > * 2 / 4 / 8 GB of DDR4 DRAM > * 16 GB eMMC > * 4MB SPI-NOR (Bootloader) > * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only) > * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only) > * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C) > * 1x SATA 7+15 socket (SATA3) > * 1x 16-pin (2×8) MikroBus Connector > * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots) > * 2x USB3.0 Type-A ports via SMSC USB5434B hub > * Cortex 2x5 JTAG > * microUSB port for UART (PL2303GL/PL2303SA onboard) > * 1x 10G SFP+ > * 1x 1G SFP (Connected to 88E1512 PHY) > * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY) > * 4x 1G RJ45 ports via Topaz 88E6141 switch > * RTC with battery holder (SoC provided, requires CR2032 battery) > * 1x 12V DC IN > * 1x Power switch > * 1x 12V fan header (3-pin, power only) > * 1x mini-PCIe LED header (2x0.1" pins) > * 1x M.2-2280 LED header (2x0.1" pins) > * 6x Bootstrap jumpers > * 1x Power LED (Green) > * 3x Tri-color RGB LEDs (Controllable) > * 1x Microchip ATECC608B secure element > > Note that 1G SFP and 1G WAN cannot be used at the same time as they are in > parallel connected to the same PHY. > > Signed-off-by: Robert Marko <robert.marko@sartura.hr> > Reviewed-by: Andrew Lunn <andrew@lunn.ch> Applied on mvebu/dt64 Thanks, Gregory > --- > Changes in v6: > * Use reset-gpios instead of reset-gpio per the DT binding > * Add the CLKREQ PCIe pinmux > > Changes in v5: > * Change LED labels to use the common "color:name" format instead > > Changes in v4: > * Rename the "u-boot" partition to "firmware" which is more appropriate > as it a concatenation of mv-ddr + TF-A + U-boot > > Changes in v3: > * Use IRQ_TYPE_LEVEL_LOW instead of IRQ_TYPE_EDGE_FALLING as both the > PCA9554 and Topaz switch have an active LOW IRQ signal. > > Changes in v2: > * Use "10gbase-r" instead of "10gbase-kr" > --- > arch/arm64/boot/dts/marvell/Makefile | 1 + > .../boot/dts/marvell/armada-7040-mochabin.dts | 458 ++++++++++++++++++ > 2 files changed, 459 insertions(+) > create mode 100644 arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts > > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile > index 34efe0fb6f37..4d3a2ae9adbd 100644 > --- a/arch/arm64/boot/dts/marvell/Makefile > +++ b/arch/arm64/boot/dts/marvell/Makefile > @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb > +dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb > dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb > diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts > new file mode 100644 > index 000000000000..f3b0d57a24a3 > --- /dev/null > +++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts > @@ -0,0 +1,458 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/* > + * Device Tree file for Globalscale MOCHAbin > + * Copyright (C) 2019 Globalscale technologies, Inc. > + * Copyright (C) 2021 Sartura Ltd. > + * > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include "armada-7040.dtsi" > + > +/ { > + model = "Globalscale MOCHAbin"; > + compatible = "globalscale,mochabin", "marvell,armada7040", > + "marvell,armada-ap806-quad", "marvell,armada-ap806"; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + aliases { > + ethernet0 = &cp0_eth0; > + ethernet1 = &cp0_eth1; > + ethernet2 = &cp0_eth2; > + ethernet3 = &swport1; > + ethernet4 = &swport2; > + ethernet5 = &swport3; > + ethernet6 = &swport4; > + }; > + > + /* SFP+ 10G */ > + sfp_eth0: sfp-eth0 { > + compatible = "sff,sfp"; > + i2c-bus = <&cp0_i2c1>; > + los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>; > + mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>; > + tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>; > + tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>; > + }; > + > + /* SFP 1G */ > + sfp_eth2: sfp-eth2 { > + compatible = "sff,sfp"; > + i2c-bus = <&cp0_i2c0>; > + los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>; > + mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>; > + tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>; > + tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +/* microUSB UART console */ > +&uart0 { > + status = "okay"; > + > + pinctrl-0 = <&uart0_pins>; > + pinctrl-names = "default"; > +}; > + > +/* eMMC */ > +&ap_sdhci0 { > + status = "okay"; > + > + bus-width = <4>; > + non-removable; > + /delete-property/ marvell,xenon-phy-slow-mode; > + no-1-8-v; > +}; > + > +&cp0_pinctrl { > + cp0_uart0_pins: cp0-uart0-pins { > + marvell,pins = "mpp6", "mpp7"; > + marvell,function = "uart0"; > + }; > + > + cp0_spi0_pins: cp0-spi0-pins { > + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59"; > + marvell,function = "spi0"; > + }; > + > + cp0_spi1_pins: cp0-spi1-pins { > + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; > + marvell,function = "spi1"; > + }; > + > + cp0_i2c0_pins: cp0-i2c0-pins { > + marvell,pins = "mpp37", "mpp38"; > + marvell,function = "i2c0"; > + }; > + > + cp0_i2c1_pins: cp0-i2c1-pins { > + marvell,pins = "mpp2", "mpp3"; > + marvell,function = "i2c1"; > + }; > + > + pca9554_int_pins: pca9554-int-pins { > + marvell,pins = "mpp27"; > + marvell,function = "gpio"; > + }; > + > + cp0_rgmii1_pins: cp0-rgmii1-pins { > + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49", > + "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55"; > + marvell,function = "ge1"; > + }; > + > + is31_sdb_pins: is31-sdb-pins { > + marvell,pins = "mpp30"; > + marvell,function = "gpio"; > + }; > + > + cp0_pcie_reset_pins: cp0-pcie-reset-pins { > + marvell,pins = "mpp9"; > + marvell,function = "gpio"; > + }; > + > + cp0_pcie_clkreq_pins: cp0-pcie-clkreq-pins { > + marvell,pins = "mpp5"; > + marvell,function = "pcie1"; > + }; > + > + cp0_switch_pins: cp0-switch-pins { > + marvell,pins = "mpp0", "mpp1"; > + marvell,function = "gpio"; > + }; > + > + cp0_phy_pins: cp0-phy-pins { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > +}; > + > +/* mikroBUS UART */ > +&cp0_uart0 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_uart0_pins>; > +}; > + > +/* mikroBUS SPI */ > +&cp0_spi0 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_spi0_pins>; > +}; > + > +/* SPI-NOR */ > +&cp0_spi1{ > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_spi1_pins>; > + > + spi-flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "firmware"; > + reg = <0x0 0x3e0000>; > + read-only; > + }; > + > + partition@3e0000 { > + label = "hw-info"; > + reg = <0x3e0000 0x10000>; > + read-only; > + }; > + > + partition@3f0000 { > + label = "u-boot-env"; > + reg = <0x3f0000 0x10000>; > + }; > + }; > + }; > +}; > + > +/* mikroBUS, 1G SFP and GPIO expander */ > +&cp0_i2c0 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_i2c0_pins>; > + clock-frequency = <100000>; > + > + sfp_gpio: pca9554@39 { > + compatible = "nxp,pca9554"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pca9554_int_pins>; > + reg = <0x39>; > + > + interrupt-parent = <&cp0_gpio1>; > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + gpio-controller; > + #gpio-cells = <2>; > + > + /* > + * IO0_0: SFP+_TX_FAULT > + * IO0_1: SFP+_TX_DISABLE > + * IO0_2: SFP+_PRSNT > + * IO0_3: SFP+_LOSS > + * IO0_4: SFP_TX_FAULT > + * IO0_5: SFP_TX_DISABLE > + * IO0_6: SFP_PRSNT > + * IO0_7: SFP_LOSS > + */ > + }; > +}; > + > +/* IS31FL3199, mini-PCIe and 10G SFP+ */ > +&cp0_i2c1 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_i2c1_pins>; > + clock-frequency = <100000>; > + > + leds@64 { > + compatible = "issi,is31fl3199"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&is31_sdb_pins>; > + shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>; > + reg = <0x64>; > + > + led1_red: led@1 { > + label = "red:led1"; > + reg = <1>; > + led-max-microamp = <20000>; > + }; > + > + led1_green: led@2 { > + label = "green:led1"; > + reg = <2>; > + }; > + > + led1_blue: led@3 { > + label = "blue:led1"; > + reg = <3>; > + }; > + > + led2_red: led@4 { > + label = "red:led2"; > + reg = <4>; > + }; > + > + led2_green: led@5 { > + label = "green:led2"; > + reg = <5>; > + }; > + > + led2_blue: led@6 { > + label = "blue:led2"; > + reg = <6>; > + }; > + > + led3_red: led@7 { > + label = "red:led3"; > + reg = <7>; > + }; > + > + led3_green: led@8 { > + label = "green:led3"; > + reg = <8>; > + }; > + > + led3_blue: led@9 { > + label = "blue:led3"; > + reg = <9>; > + }; > + }; > +}; > + > +&cp0_mdio { > + status = "okay"; > + > + /* 88E1512 PHY */ > + eth2phy: ethernet-phy@1 { > + reg = <1>; > + sfp = <&sfp_eth2>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_phy_pins>; > + reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>; > + }; > + > + /* 88E6141 Topaz switch */ > + switch: switch@3 { > + compatible = "marvell,mv88e6085"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <3>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_switch_pins>; > + reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>; > + > + interrupt-parent = <&cp0_gpio1>; > + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + swport1: port@1 { > + reg = <1>; > + label = "lan0"; > + phy-handle = <&swphy1>; > + }; > + > + swport2: port@2 { > + reg = <2>; > + label = "lan1"; > + phy-handle = <&swphy2>; > + }; > + > + swport3: port@3 { > + reg = <3>; > + label = "lan2"; > + phy-handle = <&swphy3>; > + }; > + > + swport4: port@4 { > + reg = <4>; > + label = "lan3"; > + phy-handle = <&swphy4>; > + }; > + > + port@5 { > + reg = <5>; > + label = "cpu"; > + ethernet = <&cp0_eth1>; > + phy-mode = "2500base-x"; > + managed = "in-band-status"; > + }; > + }; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + swphy1: swphy1@17 { > + reg = <17>; > + }; > + > + swphy2: swphy2@18 { > + reg = <18>; > + }; > + > + swphy3: swphy3@19 { > + reg = <19>; > + }; > + > + swphy4: swphy4@20 { > + reg = <20>; > + }; > + }; > + }; > +}; > + > +&cp0_ethernet { > + status = "okay"; > +}; > + > +/* 10G SFP+ */ > +&cp0_eth0 { > + status = "okay"; > + > + phy-mode = "10gbase-r"; > + phys = <&cp0_comphy4 0>; > + managed = "in-band-status"; > + sfp = <&sfp_eth0>; > +}; > + > +/* Topaz switch uplink */ > +&cp0_eth1 { > + status = "okay"; > + > + phy-mode = "2500base-x"; > + phys = <&cp0_comphy0 1>; > + > + fixed-link { > + speed = <2500>; > + full-duplex; > + }; > +}; > + > +/* 1G SFP or 1G RJ45 */ > +&cp0_eth2 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&cp0_rgmii1_pins>; > + > + phy = <ð2phy>; > + phy-mode = "rgmii-id"; > +}; > + > +&cp0_utmi { > + status = "okay"; > +}; > + > +/* SMSC USB5434B hub */ > +&cp0_usb3_0 { > + status = "okay"; > + > + phys = <&cp0_comphy1 0>, <&cp0_utmi0>; > + phy-names = "cp0-usb3h0-comphy", "utmi"; > +}; > + > +/* miniPCI-E USB */ > +&cp0_usb3_1 { > + status = "okay"; > +}; > + > +&cp0_sata0 { > + status = "okay"; > + > + /* 7 + 12 SATA connector (J24) */ > + sata-port@0 { > + phys = <&cp0_comphy2 0>; > + phy-names = "cp0-sata0-0-phy"; > + }; > + > + /* M.2-2250 B-key (J39) */ > + sata-port@1 { > + phys = <&cp0_comphy3 1>; > + phy-names = "cp0-sata0-1-phy"; > + }; > +}; > + > +/* miniPCI-E (J5) */ > +&cp0_pcie2 { > + status = "okay"; > + > + pinctrl-names = "default", "clkreq"; > + pinctrl-0 = <&cp0_pcie_reset_pins>; > + pinctrl-1 = <&cp0_pcie_clkreq_pins>; > + phys = <&cp0_comphy5 2>; > + phy-names = "cp0-pcie2-x1-phy"; > + reset-gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>; > +}; > -- > 2.33.0 >
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 34efe0fb6f37..4d3a2ae9adbd 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts new file mode 100644 index 000000000000..f3b0d57a24a3 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts @@ -0,0 +1,458 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Device Tree file for Globalscale MOCHAbin + * Copyright (C) 2019 Globalscale technologies, Inc. + * Copyright (C) 2021 Sartura Ltd. + * + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "armada-7040.dtsi" + +/ { + model = "Globalscale MOCHAbin"; + compatible = "globalscale,mochabin", "marvell,armada7040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + ethernet3 = &swport1; + ethernet4 = &swport2; + ethernet5 = &swport3; + ethernet6 = &swport4; + }; + + /* SFP+ 10G */ + sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&cp0_i2c1>; + los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>; + }; + + /* SFP 1G */ + sfp_eth2: sfp-eth2 { + compatible = "sff,sfp"; + i2c-bus = <&cp0_i2c0>; + los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>; + mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>; + tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>; + }; +}; + +/* microUSB UART console */ +&uart0 { + status = "okay"; + + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +/* eMMC */ +&ap_sdhci0 { + status = "okay"; + + bus-width = <4>; + non-removable; + /delete-property/ marvell,xenon-phy-slow-mode; + no-1-8-v; +}; + +&cp0_pinctrl { + cp0_uart0_pins: cp0-uart0-pins { + marvell,pins = "mpp6", "mpp7"; + marvell,function = "uart0"; + }; + + cp0_spi0_pins: cp0-spi0-pins { + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59"; + marvell,function = "spi0"; + }; + + cp0_spi1_pins: cp0-spi1-pins { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + + cp0_i2c0_pins: cp0-i2c0-pins { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + + cp0_i2c1_pins: cp0-i2c1-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c1"; + }; + + pca9554_int_pins: pca9554-int-pins { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + cp0_rgmii1_pins: cp0-rgmii1-pins { + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49", + "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55"; + marvell,function = "ge1"; + }; + + is31_sdb_pins: is31-sdb-pins { + marvell,pins = "mpp30"; + marvell,function = "gpio"; + }; + + cp0_pcie_reset_pins: cp0-pcie-reset-pins { + marvell,pins = "mpp9"; + marvell,function = "gpio"; + }; + + cp0_pcie_clkreq_pins: cp0-pcie-clkreq-pins { + marvell,pins = "mpp5"; + marvell,function = "pcie1"; + }; + + cp0_switch_pins: cp0-switch-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "gpio"; + }; + + cp0_phy_pins: cp0-phy-pins { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; +}; + +/* mikroBUS UART */ +&cp0_uart0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_uart0_pins>; +}; + +/* mikroBUS SPI */ +&cp0_spi0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; +}; + +/* SPI-NOR */ +&cp0_spi1{ + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi1_pins>; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "firmware"; + reg = <0x0 0x3e0000>; + read-only; + }; + + partition@3e0000 { + label = "hw-info"; + reg = <0x3e0000 0x10000>; + read-only; + }; + + partition@3f0000 { + label = "u-boot-env"; + reg = <0x3f0000 0x10000>; + }; + }; + }; +}; + +/* mikroBUS, 1G SFP and GPIO expander */ +&cp0_i2c0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + clock-frequency = <100000>; + + sfp_gpio: pca9554@39 { + compatible = "nxp,pca9554"; + pinctrl-names = "default"; + pinctrl-0 = <&pca9554_int_pins>; + reg = <0x39>; + + interrupt-parent = <&cp0_gpio1>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + /* + * IO0_0: SFP+_TX_FAULT + * IO0_1: SFP+_TX_DISABLE + * IO0_2: SFP+_PRSNT + * IO0_3: SFP+_LOSS + * IO0_4: SFP_TX_FAULT + * IO0_5: SFP_TX_DISABLE + * IO0_6: SFP_PRSNT + * IO0_7: SFP_LOSS + */ + }; +}; + +/* IS31FL3199, mini-PCIe and 10G SFP+ */ +&cp0_i2c1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + clock-frequency = <100000>; + + leds@64 { + compatible = "issi,is31fl3199"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&is31_sdb_pins>; + shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>; + reg = <0x64>; + + led1_red: led@1 { + label = "red:led1"; + reg = <1>; + led-max-microamp = <20000>; + }; + + led1_green: led@2 { + label = "green:led1"; + reg = <2>; + }; + + led1_blue: led@3 { + label = "blue:led1"; + reg = <3>; + }; + + led2_red: led@4 { + label = "red:led2"; + reg = <4>; + }; + + led2_green: led@5 { + label = "green:led2"; + reg = <5>; + }; + + led2_blue: led@6 { + label = "blue:led2"; + reg = <6>; + }; + + led3_red: led@7 { + label = "red:led3"; + reg = <7>; + }; + + led3_green: led@8 { + label = "green:led3"; + reg = <8>; + }; + + led3_blue: led@9 { + label = "blue:led3"; + reg = <9>; + }; + }; +}; + +&cp0_mdio { + status = "okay"; + + /* 88E1512 PHY */ + eth2phy: ethernet-phy@1 { + reg = <1>; + sfp = <&sfp_eth2>; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_phy_pins>; + reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>; + }; + + /* 88E6141 Topaz switch */ + switch: switch@3 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_switch_pins>; + reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>; + + interrupt-parent = <&cp0_gpio1>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + swport1: port@1 { + reg = <1>; + label = "lan0"; + phy-handle = <&swphy1>; + }; + + swport2: port@2 { + reg = <2>; + label = "lan1"; + phy-handle = <&swphy2>; + }; + + swport3: port@3 { + reg = <3>; + label = "lan2"; + phy-handle = <&swphy3>; + }; + + swport4: port@4 { + reg = <4>; + label = "lan3"; + phy-handle = <&swphy4>; + }; + + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&cp0_eth1>; + phy-mode = "2500base-x"; + managed = "in-band-status"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + swphy1: swphy1@17 { + reg = <17>; + }; + + swphy2: swphy2@18 { + reg = <18>; + }; + + swphy3: swphy3@19 { + reg = <19>; + }; + + swphy4: swphy4@20 { + reg = <20>; + }; + }; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +/* 10G SFP+ */ +&cp0_eth0 { + status = "okay"; + + phy-mode = "10gbase-r"; + phys = <&cp0_comphy4 0>; + managed = "in-band-status"; + sfp = <&sfp_eth0>; +}; + +/* Topaz switch uplink */ +&cp0_eth1 { + status = "okay"; + + phy-mode = "2500base-x"; + phys = <&cp0_comphy0 1>; + + fixed-link { + speed = <2500>; + full-duplex; + }; +}; + +/* 1G SFP or 1G RJ45 */ +&cp0_eth2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&cp0_rgmii1_pins>; + + phy = <ð2phy>; + phy-mode = "rgmii-id"; +}; + +&cp0_utmi { + status = "okay"; +}; + +/* SMSC USB5434B hub */ +&cp0_usb3_0 { + status = "okay"; + + phys = <&cp0_comphy1 0>, <&cp0_utmi0>; + phy-names = "cp0-usb3h0-comphy", "utmi"; +}; + +/* miniPCI-E USB */ +&cp0_usb3_1 { + status = "okay"; +}; + +&cp0_sata0 { + status = "okay"; + + /* 7 + 12 SATA connector (J24) */ + sata-port@0 { + phys = <&cp0_comphy2 0>; + phy-names = "cp0-sata0-0-phy"; + }; + + /* M.2-2250 B-key (J39) */ + sata-port@1 { + phys = <&cp0_comphy3 1>; + phy-names = "cp0-sata0-1-phy"; + }; +}; + +/* miniPCI-E (J5) */ +&cp0_pcie2 { + status = "okay"; + + pinctrl-names = "default", "clkreq"; + pinctrl-0 = <&cp0_pcie_reset_pins>; + pinctrl-1 = <&cp0_pcie_clkreq_pins>; + phys = <&cp0_comphy5 2>; + phy-names = "cp0-pcie2-x1-phy"; + reset-gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>; +};