diff mbox series

[v2,2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM

Message ID 20211105153025.187106-3-alexander.stein@ew.tq-group.com (mailing list archive)
State New, archived
Headers show
Series Support for some TQMa8M* boards | expand

Commit Message

Alexander Stein Nov. 5, 2021, 3:30 p.m. UTC
This adds support for TQMa8MQML module on MBa8Mx board.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Fixed ordering in Makefile
* Renamed codec -> audio_codec
* Add USB interfaces & USB extcon & pinctrl nodes
* Fixed pinctrl node names
* Removed empty chosen node
* Removed regulator-always-on on non-switchable regulators
* Changed spi-tx-bus-width for spi-nor flash similar to commit 04aa946d57b2
  ("arm64: dts: imx8: change the spi-nor tx")
* Enabled gpu_2d and gpu_3d nodes
* Removed Ethernet PHY IRQ support (was unreliable)

 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 299 +++++++++++++++
 .../boot/dts/freescale/imx8mm-tqma8mqml.dtsi  | 353 ++++++++++++++++++
 arch/arm64/boot/dts/freescale/mba8mx.dtsi     | 283 ++++++++++++++
 4 files changed, 936 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi

Comments

Shawn Guo Nov. 23, 2021, 8:02 a.m. UTC | #1
On Fri, Nov 05, 2021 at 04:30:20PM +0100, Alexander Stein wrote:
> This adds support for TQMa8MQML module on MBa8Mx board.
> 
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>

In subject, s/tree/device tree

> ---
> Changes in v2:
> * Fixed ordering in Makefile
> * Renamed codec -> audio_codec
> * Add USB interfaces & USB extcon & pinctrl nodes
> * Fixed pinctrl node names
> * Removed empty chosen node
> * Removed regulator-always-on on non-switchable regulators
> * Changed spi-tx-bus-width for spi-nor flash similar to commit 04aa946d57b2
>   ("arm64: dts: imx8: change the spi-nor tx")
> * Enabled gpu_2d and gpu_3d nodes
> * Removed Ethernet PHY IRQ support (was unreliable)
> 
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 299 +++++++++++++++
>  .../boot/dts/freescale/imx8mm-tqma8mqml.dtsi  | 353 ++++++++++++++++++
>  arch/arm64/boot/dts/freescale/mba8mx.dtsi     | 283 ++++++++++++++
>  4 files changed, 936 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index a14a6173b765..33c21322bf15 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> new file mode 100644
> index 000000000000..de05294bf0b1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> @@ -0,0 +1,299 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm-tqma8mqml.dtsi"
> +#include "mba8mx.dtsi"
> +
> +/ {
> +	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
> +	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> +	aliases {
> +		eeprom0 = &eeprom3;
> +		mmc0 = &usdhc3;
> +		mmc1 = &usdhc2;
> +		mmc2 = &usdhc1;
> +		rtc0 = &pcf85063;
> +		rtc1 = &snvs_rtc;
> +	};
> +
> +	reg_usdhc2_vmmc: regulator-vmmc {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> +		regulator-name = "VSD_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		startup-delay-us = <100>;
> +		off-on-delay-us = <12000>;
> +	};
> +
> +	extcon_usbotg1: extcon-usbotg1 {
> +		compatible = "linux,extcon-usb-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usb1_extcon>;
> +		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&audio_codec {
> +	clock-names = "mclk";
> +	clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
> +};
> +
> +&i2c1 {
> +	expander2: gpio@27 {
> +		compatible = "nxp,pca9555";
> +		reg = <0x27>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		vcc-supply = <&reg_vcc_3v3>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_expander>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +};
> +
> +&sai3 {
> +	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> +	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> +	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
> +	clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
> +		<&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
> +		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
> +		<&clk IMX8MM_AUDIO_PLL2_OUT>;
> +};
> +
> +&uart1 {
> +	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
> +	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&uart2 {
> +	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> +	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&usbotg1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg1>;
> +	dr_mode = "otg";
> +	extcon = <&extcon_usbotg1>;
> +	srp-disable;
> +	hnp-disable;
> +	adp-disable;
> +	power-active-high;
> +	over-current-active-low;
> +	status = "okay";
> +};
> +
> +&usbotg2 {
> +	dr_mode = "host";
> +	disable-over-current;
> +	vbus-supply = <&reg_hub_vbus>;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_ecspi1: ecspi1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x00000006
> +			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x00000006
> +			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x00000006
> +			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x00000006
> +		>;
> +	};
> +
> +	pinctrl_ecspi2: ecspi2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x00000006
> +			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x00000006
> +			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x00000006
> +			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0x00000006
> +		>;
> +	};
> +
> +	pinctrl_expander: expandergrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x94
> +		>;
> +	};
> +
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002
> +			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO	0x40000002
> +			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x14
> +			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x14
> +			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x14
> +			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x14
> +			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x90
> +			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x90
> +			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x90
> +			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x90
> +			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x14
> +			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x90
> +			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90
> +			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14
> +		>;
> +	};
> +
> +	pinctrl_gpiobutton: gpiobuttongrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x84
> +			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x84
> +			MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0		0x84
> +		>;
> +	};
> +
> +	pinctrl_gpioled: gpioledgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0	0x84
> +			MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14	0x84
> +		>;
> +	};
> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x40000004
> +			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x40000004
> +		>;
> +	};
> +
> +	pinctrl_i2c2_gpio: i2c2gpiogrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16	0x40000004
> +			MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17	0x40000004
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x40000004
> +			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x40000004
> +		>;
> +	};
> +
> +	pinctrl_i2c3_gpio: i2c3gpiogrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18	0x40000004
> +			MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19	0x40000004
> +		>;
> +	};
> +
> +	pinctrl_pwm3: pwm3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT	0x14
> +		>;
> +	};
> +
> +	pinctrl_pwm4: pwm4grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT	0x14
> +		>;
> +	};
> +
> +	pinctrl_sai3: sai3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK	0x94
> +			MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK	0x94
> +			MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC	0x94
> +			MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0	0x94
> +			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC	0x94
> +			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0	0x94
> +			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK	0x94
> +		>;
> +	};
> +
> +	pinctrl_uart1: uart1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x16
> +			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x16
> +		>;
> +	};
> +
> +	pinctrl_uart2: uart2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x16
> +			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x16
> +		>;
> +	};
> +
> +	pinctrl_uart3: uart3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x16
> +			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x16
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX	0x16
> +			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX	0x16
> +		>;
> +	};
> +
> +	pinctrl_usbotg1: usbotg1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x84
> +			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x84
> +		>;
> +	};
> +
> +	pinctrl_usb1_extcon: usb1_extcongrp {

Instead of underscore, hyphen is recommended for node name.

> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x1c0
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
> +			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
> +			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
> +			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
> +			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
> +			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
> +			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> new file mode 100644
> index 000000000000..9459e78a7d00
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> @@ -0,0 +1,353 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include "imx8mm.dtsi"
> +
> +/ {
> +	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
> +	compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +		/*  our minimum RAM config will be 1024 MiB */
> +		reg = <0x00000000 0x40000000 0 0x40000000>;
> +	};
> +
> +	/* e-MMC IO, needed for HS modes */
> +	reg_vcc1v8: regulator-vcc1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "TQMA8MXML_VCC1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	/* identical to buck4_reg, but should never change */
> +	reg_vcc3v3: regulator-vcc3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "TQMA8MXML_VCC3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		/* global autoconfigured region for contiguous allocations */
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			reusable;
> +			/* 640 MiB */
> +			size = <0 0x28000000>;
> +			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
> +			alloc-ranges = <0 0x40000000 0 0x78000000>;
> +			linux,cma-default;
> +		};
> +	};
> +};
> +
> +&A53_0 {
> +	cpu-supply = <&buck2_reg>;
> +};
> +
> +&flexspi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexspi>;
> +	status = "okay";
> +
> +	flash0: flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		spi-max-frequency = <84000000>;
> +		spi-tx-bus-width = <1>;
> +		spi-rx-bus-width = <4>;
> +	};
> +};
> +
> +&gpu_2d {
> +	status = "okay";
> +};
> +
> +&gpu_3d {
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default", "gpio";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	pinctrl-1 = <&pinctrl_i2c1_gpio>;
> +	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	status = "okay";
> +
> +	sensor0: temperature-sensor-eeprom@1b {
> +		compatible = "nxp,se97", "jedec,jc-42.4-temp";
> +		reg = <0x1b>;
> +	};
> +
> +	pca9450: pmic@25 {
> +		compatible = "nxp,pca9450a";
> +		reg = <0x25>;
> +
> +		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		pinctrl-names = "default";
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +
> +		regulators {
> +			/* V_0V85_SOC: 0.85 */
> +			buck1_reg: BUCK1 {
> +				regulator-name = "BUCK1";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			/* VDD_ARM */
> +			buck2_reg: BUCK2 {
> +				regulator-name = "BUCK2";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				nxp,dvs-run-voltage = <950000>;
> +				nxp,dvs-standby-voltage = <850000>;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			/* V_0V85_GPU / DRAM / VPU */
> +			buck3_reg: BUCK3 {
> +				regulator-name = "BUCK3";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <3125>;
> +			};
> +
> +			/* VCC3V3 -> VMMC, ... must not be changed */
> +			buck4_reg: BUCK4 {
> +				regulator-name = "BUCK4";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
> +			buck5_reg: BUCK5 {
> +				regulator-name = "BUCK5";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_1V1 -> RAM, ... must not be changed */
> +			buck6_reg: BUCK6 {
> +				regulator-name = "BUCK6";
> +				regulator-min-microvolt = <1100000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_1V8_SNVS */
> +			ldo1_reg: LDO1 {
> +				regulator-name = "LDO1";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_0V8_SNVS */
> +			ldo2_reg: LDO2 {
> +				regulator-name = "LDO2";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_1V8_ANA */
> +			ldo3_reg: LDO3 {
> +				regulator-name = "LDO3";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* V_0V9_MIPI */
> +			ldo4_reg: LDO4 {
> +				regulator-name = "LDO4";
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			/* VCC SD IO - switched using SD2 VSELECT */
> +			ldo5_reg: LDO5 {
> +				regulator-name = "LDO5";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +		};
> +	};
> +
> +
> +	pcf85063: rtc@51 {
> +		compatible = "nxp,pcf85063a";
> +		reg = <0x51>;
> +		quartz-load-femtofarads = <7000>;
> +	};
> +
> +	eeprom1: eeprom@53 {
> +		compatible = "nxp,se97b", "atmel,24c02";
> +		read-only;
> +		reg = <0x53>;
> +		pagesize = <16>;
> +	};
> +
> +	eeprom0: eeprom@57 {
> +		compatible = "atmel,24c64";
> +		reg = <0x57>;
> +		pagesize = <32>;
> +	};
> +};
> +
> +&usdhc3 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> +	bus-width = <8>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	vqmmc-supply = <&reg_vcc1v8>;
> +	status = "okay";
> +};
> +
> +/*
> + * Attention:
> + * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
> + * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
> + */
> +&wdog1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_wdog>;
> +	fsl,ext-reset-output;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_flexspi: flexspigrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK	0x82
> +			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82
> +			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82
> +			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82
> +			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82
> +			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000004
> +			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000004
> +		>;
> +	};
> +
> +	pinctrl_i2c1_gpio: i2c1gpiogrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x40000004
> +			MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x40000004
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x94
> +		>;
> +	};
> +
> +	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
> +			/* option USDHC3_RESET_B not defined, only in RM */
> +			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
> +			/* option USDHC3_RESET_B not defined, only in RM */
> +			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
> +		>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6
> +			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
> +			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
> +			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
> +			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
> +			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
> +			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
> +			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
> +			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
> +			/* option USDHC3_RESET_B not defined, only in RM */
> +			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
> +		>;
> +	};
> +
> +	pinctrl_wdog: wdoggrp {
> +		fsl,pins = <
> +			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x84
> +		>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> new file mode 100644
> index 000000000000..92b48ffc41dd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> @@ -0,0 +1,283 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/* TQ-Systems GmbH MBa8Mx baseboard */
> +
> +/ {
> +	beeper {
> +		compatible = "pwm-beeper";
> +		pwms = <&pwm4 0 250000 0>;
> +		beeper-hz = <4000>;
> +		amp-supply = <&reg_vcc_3v3>;
> +	};
> +
> +	chosen {
> +		bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";

Do you really need bootargs in DT?

> +		stdout-path = &uart3;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpiobutton>;
> +		autorepeat;
> +
> +		switch1 {
> +			label = "switch1";
> +			linux,code = <BTN_0>;
> +			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +		};
> +
> +		btn2: switch2 {
> +			label = "switch2";
> +			linux,code = <BTN_1>;
> +			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +		};
> +
> +		switch3 {
> +			label = "switch3";
> +			linux,code = <BTN_2>;
> +			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	gpio_leds: gpio-leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpioled>;
> +
> +		led1 {
> +			label = "led1";
> +			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "default-on";
> +		};
> +
> +		led2: led2 {
> +			label = "led2";
> +			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +
> +	reg_hub_vbus: regulator-hub-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "MBA8MX_HUB_VBUS";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SN65DSI83_1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_vcc_3v3: regulator-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "MBA8MX_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx-audio-tlv320aic32x4";
> +		model = "tqm-tlv320aic32";
> +		ssi-controller = <&sai3>;
> +		audio-codec = <&audio_codec>;
> +	};
> +};
> +
> +&ecspi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi1>;
> +	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&ecspi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi2>;
> +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	phy-supply = <&reg_vcc_3v3>;
> +	fsl,magic-packet;
> +	mac-address = [ 00 00 00 00 00 00 ];
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@e {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0xe>;
> +			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> +			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> +			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> +			ti,dp83867-rxctrl-strap-quirk;
> +			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> +			enet-phy-lane-no-swap;

Undocumented property?

> +			reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <500000>;
> +			reset-deassert-us = <500>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	expander0: gpio@23 {
> +		compatible = "nxp,pca9555";
> +		reg = <0x23>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		vcc-supply = <&reg_vcc_3v3>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +
> +		sd-mux-oe-hog {
> +			gpio-hog;
> +			gpios = <8 0>;
> +			output-low;
> +			line-name = "SD_MUX_EN#";
> +		};
> +
> +		boot-cfg-oe-hog {
> +			gpio-hog;
> +			gpios = <12 0>;
> +			output-high;
> +			line-name = "BOOT_CFG_OE#";
> +		};
> +
> +		rst-usb-hub-hog {
> +			gpio-hog;
> +			gpios = <13 0>;
> +			output-high;
> +			line-name = "RST_USB_HUB#";
> +		};
> +	};
> +
> +	expander1: gpio@24 {
> +		compatible = "nxp,pca9555";
> +		reg = <0x24>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		vcc-supply = <&reg_vcc_3v3>;
> +	};
> +};
> +
> +&i2c2 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default", "gpio";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	pinctrl-1 = <&pinctrl_i2c2_gpio>;
> +	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	status = "okay";
> +
> +	audio_codec: tlv320aic3x04@18 {

Node name should be generic while label can be specific, so:

	tlv320aic3x04: audio-codec@18

> +		compatible = "ti,tlv320aic32x4";
> +		reg = <0x18>;
> +		reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
> +		iov-supply = <&reg_vcc_3v3>;
> +		ldoin-supply = <&reg_vcc_3v3>;
> +	};
> +
> +	sensor1: sensor@1f {
> +		compatible = "nxp,se97", "jedec,jc-42.4-temp";
> +		reg = <0x1f>;
> +	};
> +
> +	eeprom3: eeprom@57 {
> +		compatible = "nxp,se97b", "atmel,24c02";
> +		reg = <0x57>;
> +		pagesize = <16>;
> +	};
> +};
> +
> +&i2c3 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default", "gpio";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	pinctrl-1 = <&pinctrl_i2c3_gpio>;
> +	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +	status = "okay";
> +};
> +
> +&pwm3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm3>;
> +	status = "okay";
> +};
> +
> +&pwm4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm4>;
> +	status = "okay";
> +};
> +
> +&sai3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_sai3>;
> +	#sound-dai-cells = <0>;
> +	assigned-clock-rates = <49152000>;
> +	status = "okay";
> +};
> +
> +&snvs_pwrkey {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2>;
> +	status = "okay";
> +};
> +
> +/* console */
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart3>;
> +	status = "okay";
> +};
> +
> +/* UART4 is assigned to Cortex-M4 */
> +

Unneeded newline.

Shawn

> +&usdhc2 {
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> +	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> +	bus-width = <4>;
> +	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	no-mmc;
> +	no-sdio;
> +	vmmc-supply = <&reg_usdhc2_vmmc>;
> +	status = "okay";
> +};
> -- 
> 2.25.1
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a14a6173b765..33c21322bf15 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -40,6 +40,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
new file mode 100644
index 000000000000..de05294bf0b1
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -0,0 +1,299 @@ 
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
+	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+	aliases {
+		eeprom0 = &eeprom3;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc1;
+		rtc0 = &pcf85063;
+		rtc1 = &snvs_rtc;
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+
+	extcon_usbotg1: extcon-usbotg1 {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_extcon>;
+		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&audio_codec {
+	clock-names = "mclk";
+	clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+};
+
+&i2c1 {
+	expander2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
+
+&sai3 {
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+	clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+		<&clk IMX8MM_AUDIO_PLL2_OUT>;
+};
+
+&uart1 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&uart2 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "otg";
+	extcon = <&extcon_usbotg1>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	power-active-high;
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	vbus-supply = <&reg_hub_vbus>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x00000006
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x00000006
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x00000006
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x00000006
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x00000006
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x00000006
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x00000006
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0x00000006
+		>;
+	};
+
+	pinctrl_expander: expandergrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x94
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO	0x40000002
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x14
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x14
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x14
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x14
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x90
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x90
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x90
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x90
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x14
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x90
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14
+		>;
+	};
+
+	pinctrl_gpiobutton: gpiobuttongrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x84
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x84
+			MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0		0x84
+		>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0	0x84
+			MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14	0x84
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x40000004
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x40000004
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16	0x40000004
+			MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17	0x40000004
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x40000004
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x40000004
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18	0x40000004
+			MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19	0x40000004
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT	0x14
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT	0x14
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK	0x94
+			MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK	0x94
+			MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC	0x94
+			MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0	0x94
+			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC	0x94
+			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0	0x94
+			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK	0x94
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x16
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x16
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x16
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x16
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x16
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x16
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX	0x16
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX	0x16
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x84
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x84
+		>;
+	};
+
+	pinctrl_usb1_extcon: usb1_extcongrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x1c0
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x84
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 000000000000..9459e78a7d00
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,353 @@ 
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+	compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*  our minimum RAM config will be 1024 MiB */
+		reg = <0x00000000 0x40000000 0 0x40000000>;
+	};
+
+	/* e-MMC IO, needed for HS modes */
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXML_VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	/* identical to buck4_reg, but should never change */
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXML_VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			/* 640 MiB */
+			size = <0 0x28000000>;
+			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+			alloc-ranges = <0 0x40000000 0 0x78000000>;
+			linux,cma-default;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <84000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&gpu_2d {
+	status = "okay";
+};
+
+&gpu_3d {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	sensor0: temperature-sensor-eeprom@1b {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			/* V_0V85_SOC: 0.85 */
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VDD_ARM */
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* V_0V85_GPU / DRAM / VPU */
+			buck3_reg: BUCK3 {
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VCC3V3 -> VMMC, ... must not be changed */
+			buck4_reg: BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+			buck5_reg: BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V1 -> RAM, ... must not be changed */
+			buck6_reg: BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_SNVS */
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V8_SNVS */
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_ANA */
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V9_MIPI */
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* VCC SD IO - switched using SD2 VSELECT */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+
+	eeprom1: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		read-only;
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	eeprom0: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi: flexspigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK	0x82
+			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82
+			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82
+			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82
+			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82
+			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000004
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000004
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x40000004
+			MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x40000004
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x94
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
+			/* option USDHC3_RESET_B not defined, only in RM */
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
+			/* option USDHC3_RESET_B not defined, only in RM */
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x84
+			/* option USDHC3_RESET_B not defined, only in RM */
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x84
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x84
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
new file mode 100644
index 000000000000..92b48ffc41dd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
@@ -0,0 +1,283 @@ 
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/* TQ-Systems GmbH MBa8Mx baseboard */
+
+/ {
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 250000 0>;
+		beeper-hz = <4000>;
+		amp-supply = <&reg_vcc_3v3>;
+	};
+
+	chosen {
+		bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
+		stdout-path = &uart3;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobutton>;
+		autorepeat;
+
+		switch1 {
+			label = "switch1";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		btn2: switch2 {
+			label = "switch2";
+			linux,code = <BTN_1>;
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		switch3 {
+			label = "switch3";
+			linux,code = <BTN_2>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2: led2 {
+			label = "led2";
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_hub_vbus: regulator-hub-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "MBA8MX_HUB_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "SN65DSI83_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vcc_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MBA8MX_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "tqm-tlv320aic32";
+		ssi-controller = <&sai3>;
+		audio-codec = <&audio_codec>;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_vcc_3v3>;
+	fsl,magic-packet;
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@e {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0xe>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <500>;
+		};
+	};
+};
+
+&i2c1 {
+	expander0: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		sd-mux-oe-hog {
+			gpio-hog;
+			gpios = <8 0>;
+			output-low;
+			line-name = "SD_MUX_EN#";
+		};
+
+		boot-cfg-oe-hog {
+			gpio-hog;
+			gpios = <12 0>;
+			output-high;
+			line-name = "BOOT_CFG_OE#";
+		};
+
+		rst-usb-hub-hog {
+			gpio-hog;
+			gpios = <13 0>;
+			output-high;
+			line-name = "RST_USB_HUB#";
+		};
+	};
+
+	expander1: gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	audio_codec: tlv320aic3x04@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
+		iov-supply = <&reg_vcc_3v3>;
+		ldoin-supply = <&reg_vcc_3v3>;
+	};
+
+	sensor1: sensor@1f {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1f>;
+	};
+
+	eeprom3: eeprom@57 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	#sound-dai-cells = <0>;
+	assigned-clock-rates = <49152000>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* UART4 is assigned to Cortex-M4 */
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-mmc;
+	no-sdio;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};