| Message ID | 20220112151814.24361-11-pali@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | PCI: mvebu: subsystem ids, AER and INTx | expand |
On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > This adds support for legacy INTx interrupts received from other PCIe > devices and which are reported by a new INTx irq chip. > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > interrupts. > > Note that for this support, device tree files has to be properly adjusted > to provide "interrupts" or "interrupts-extended" property with intx > interrupt source, "interrupt-names" property with "intx" string and also > 'interrupt-controller' subnode must be defined. > > If device tree files do not provide these nodes then driver would work as > before. Nit: this information is not useful. DT rules are written in DT bindings, not in kernel commit logs. All I am saying is that firmware developers should not have to read this log to write firmware. > Signed-off-by: Pali Rohár <pali@kernel.org> > --- > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > 1 file changed, 177 insertions(+), 8 deletions(-) > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > index 1e90ab888075..dbb6ecb4cb70 100644 > --- a/drivers/pci/controller/pci-mvebu.c > +++ b/drivers/pci/controller/pci-mvebu.c > @@ -54,9 +54,10 @@ > PCIE_CONF_ADDR_EN) > #define PCIE_CONF_DATA_OFF 0x18fc > #define PCIE_INT_CAUSE_OFF 0x1900 > +#define PCIE_INT_UNMASK_OFF 0x1910 Nit: I understand it is tempting but here you are redefining or better giving a proper label to a register. Separate patch please. > +#define PCIE_INT_INTX(i) BIT(24+i) > #define PCIE_INT_PM_PME BIT(28) > -#define PCIE_MASK_OFF 0x1910 See above. > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > #define PCIE_CTRL_OFF 0x1a00 > #define PCIE_CTRL_X1_MODE 0x0001 > #define PCIE_CTRL_RC_MODE BIT(1) > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > struct mvebu_pcie_window iowin; > u32 saved_pcie_stat; > struct resource regs; > + struct irq_domain *intx_irq_domain; > + raw_spinlock_t irq_lock; > + int intx_irq; > }; > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > { > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > /* Setup PCIe controller to Root Complex mode. */ > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > /* Point PCIe unit MBUS decode windows to DRAM space. */ > mvebu_pcie_setup_wins(port); > > - /* Enable interrupt lines A-D. */ > - mask = mvebu_readl(port, PCIE_MASK_OFF); > - mask |= PCIE_MASK_ENABLE_INTS; > - mvebu_writel(port, mask, PCIE_MASK_OFF); > + /* Mask all interrupt sources. */ > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > + > + /* Clear all interrupt causes. */ > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > + > + if (port->intx_irq <= 0) { > + /* > + * When neither "summary" interrupt, nor "intx" interrupt was > + * specified in DT then unmask all legacy INTx interrupts as in > + * this case driver does not provide a way for masking and > + * unmasking of individual legacy INTx interrupts. In this case > + * all interrupts, including legacy INTx are reported via one > + * shared GIC source and therefore kernel cannot distinguish > + * which individual legacy INTx was triggered. These interrupts > + * are shared, so it should not cause any issue. Just > + * performance penalty as every PCIe interrupt handler needs to > + * be called when some interrupt is triggered. > + */ This comment applies to current mainline right (ie it describes how current mainline handles INTx) ? IMO you should split it out in a separate patch. I understand it is hard but a patch is a logical _change_, this comment is a change per se, it is a clarification on current behaviour. > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > + unmask |= PCIE_INT_INTX(0) | PCIE_INT_INTX(1) | > + PCIE_INT_INTX(2) | PCIE_INT_INTX(3); > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > + } > } > > static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, > @@ -924,6 +948,108 @@ static struct pci_ops mvebu_pcie_ops = { > .write = mvebu_pcie_wr_conf, > }; > > +static void mvebu_pcie_intx_irq_mask(struct irq_data *d) > +{ > + struct mvebu_pcie_port *port = d->domain->host_data; > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > + unsigned long flags; > + u32 unmask; > + > + raw_spin_lock_irqsave(&port->irq_lock, flags); > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > + unmask &= ~PCIE_INT_INTX(hwirq); > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > +} > + > +static void mvebu_pcie_intx_irq_unmask(struct irq_data *d) > +{ > + struct mvebu_pcie_port *port = d->domain->host_data; > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > + unsigned long flags; > + u32 unmask; > + > + raw_spin_lock_irqsave(&port->irq_lock, flags); > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > + unmask |= PCIE_INT_INTX(hwirq); > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > +} > + > +static struct irq_chip intx_irq_chip = { > + .name = "mvebu-INTx", > + .irq_mask = mvebu_pcie_intx_irq_mask, > + .irq_unmask = mvebu_pcie_intx_irq_unmask, > +}; > + > +static int mvebu_pcie_intx_irq_map(struct irq_domain *h, > + unsigned int virq, irq_hw_number_t hwirq) > +{ > + struct mvebu_pcie_port *port = h->host_data; > + > + irq_set_status_flags(virq, IRQ_LEVEL); > + irq_set_chip_and_handler(virq, &intx_irq_chip, handle_level_irq); > + irq_set_chip_data(virq, port); > + > + return 0; > +} > + > +static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { > + .map = mvebu_pcie_intx_irq_map, > + .xlate = irq_domain_xlate_onecell, > +}; > + > +static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) > +{ > + struct device *dev = &port->pcie->pdev->dev; > + struct device_node *pcie_intc_node; > + > + raw_spin_lock_init(&port->irq_lock); > + > + pcie_intc_node = of_get_next_child(port->dn, NULL); > + if (!pcie_intc_node) { > + dev_err(dev, "No PCIe Intc node found for %s\n", port->name); > + return -ENODEV; > + } > + > + port->intx_irq_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, > + &mvebu_pcie_intx_irq_domain_ops, > + port); > + of_node_put(pcie_intc_node); > + if (!port->intx_irq_domain) { > + dev_err(dev, "Failed to get INTx IRQ domain for %s\n", port->name); > + return -ENOMEM; > + } > + > + return 0; > +} > + > +static void mvebu_pcie_irq_handler(struct irq_desc *desc) > +{ > + struct mvebu_pcie_port *port = irq_desc_get_handler_data(desc); > + struct irq_chip *chip = irq_desc_get_chip(desc); > + struct device *dev = &port->pcie->pdev->dev; > + u32 cause, unmask, status; > + int i; > + > + chained_irq_enter(chip, desc); > + > + cause = mvebu_readl(port, PCIE_INT_CAUSE_OFF); > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > + status = cause & unmask; > + > + /* Process legacy INTx interrupts */ > + for (i = 0; i < PCI_NUM_INTX; i++) { > + if (!(status & PCIE_INT_INTX(i))) > + continue; > + > + if (generic_handle_domain_irq(port->intx_irq_domain, i) == -EINVAL) > + dev_err_ratelimited(dev, "unexpected INT%c IRQ\n", (char)i+'A'); > + } > + > + chained_irq_exit(chip, desc); > +} > + > static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) > { > /* Interrupt support on mvebu emulated bridges is not implemented yet */ > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > port->io_attr = -1; > } > > + /* > + * Old DT bindings do not contain "intx" interrupt > + * so do not fail probing driver when interrupt does not exist. > + */ > + port->intx_irq = of_irq_get_byname(child, "intx"); > + if (port->intx_irq == -EPROBE_DEFER) { > + ret = port->intx_irq; > + goto err; > + } > + if (port->intx_irq <= 0) { > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > + "%pOF does not contain intx interrupt\n", > + port->name, child); Here you end up with a new warning on existing firmware. Is it legitimate ? I would remove the dev_warn(). Rob certainly has more insightful advice on this. Thanks, Lorenzo > + } > + > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); > if (reset_gpio == -EPROBE_DEFER) { > ret = reset_gpio; > @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > for (i = 0; i < pcie->nports; i++) { > struct mvebu_pcie_port *port = &pcie->ports[i]; > + int irq = port->intx_irq; > > child = port->dn; > if (!child) > @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > continue; > } > > + if (irq > 0) { > + ret = mvebu_pcie_init_irq_domain(port); > + if (ret) { > + dev_err(dev, "%s: cannot init irq domain\n", > + port->name); > + pci_bridge_emul_cleanup(&port->bridge); > + devm_iounmap(dev, port->base); > + port->base = NULL; > + mvebu_pcie_powerdown(port); > + continue; > + } > + irq_set_chained_handler_and_data(irq, > + mvebu_pcie_irq_handler, > + port); > + } > + > /* > * PCIe topology exported by mvebu hw is quite complicated. In > * reality has something like N fully independent host bridges > @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > for (i = 0; i < pcie->nports; i++) { > struct mvebu_pcie_port *port = &pcie->ports[i]; > + int irq = port->intx_irq; > > if (!port->base) > continue; > @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > mvebu_writel(port, cmd, PCIE_CMD_OFF); > > /* Mask all interrupt sources. */ > - mvebu_writel(port, 0, PCIE_MASK_OFF); > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > + > + /* Clear all interrupt causes. */ > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > + > + if (irq > 0) > + irq_set_chained_handler_and_data(irq, NULL, NULL); > + > + /* Remove IRQ domains. */ > + if (port->intx_irq_domain) > + irq_domain_remove(port->intx_irq_domain); > > /* Free config space for emulated root bridge. */ > pci_bridge_emul_cleanup(&port->bridge); > -- > 2.20.1 >
On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > This adds support for legacy INTx interrupts received from other PCIe > > devices and which are reported by a new INTx irq chip. > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > interrupts. > > > > Note that for this support, device tree files has to be properly adjusted > > to provide "interrupts" or "interrupts-extended" property with intx > > interrupt source, "interrupt-names" property with "intx" string and also > > 'interrupt-controller' subnode must be defined. > > > > If device tree files do not provide these nodes then driver would work as > > before. > > Nit: this information is not useful. DT rules are written in DT > bindings, not in kernel commit logs. All I am saying is that firmware > developers should not have to read this log to write firmware. It was not intended for firmware developers, but for reviewers of this patch to understand, what is happening in code and that with old DT files this patch does not change driver behavior (= work as before). > > Signed-off-by: Pali Rohár <pali@kernel.org> > > --- > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > index 1e90ab888075..dbb6ecb4cb70 100644 > > --- a/drivers/pci/controller/pci-mvebu.c > > +++ b/drivers/pci/controller/pci-mvebu.c > > @@ -54,9 +54,10 @@ > > PCIE_CONF_ADDR_EN) > > #define PCIE_CONF_DATA_OFF 0x18fc > > #define PCIE_INT_CAUSE_OFF 0x1900 > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > Nit: I understand it is tempting but here you are redefining or better > giving a proper label to a register. Separate patch please. Ok! > > +#define PCIE_INT_INTX(i) BIT(24+i) > > #define PCIE_INT_PM_PME BIT(28) > > -#define PCIE_MASK_OFF 0x1910 > > See above. > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > #define PCIE_CTRL_OFF 0x1a00 > > #define PCIE_CTRL_X1_MODE 0x0001 > > #define PCIE_CTRL_RC_MODE BIT(1) > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > struct mvebu_pcie_window iowin; > > u32 saved_pcie_stat; > > struct resource regs; > > + struct irq_domain *intx_irq_domain; > > + raw_spinlock_t irq_lock; > > + int intx_irq; > > }; > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > { > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > /* Setup PCIe controller to Root Complex mode. */ > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > mvebu_pcie_setup_wins(port); > > > > - /* Enable interrupt lines A-D. */ > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > - mask |= PCIE_MASK_ENABLE_INTS; > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > + /* Mask all interrupt sources. */ > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > + > > + /* Clear all interrupt causes. */ > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > + > > + if (port->intx_irq <= 0) { > > + /* > > + * When neither "summary" interrupt, nor "intx" interrupt was > > + * specified in DT then unmask all legacy INTx interrupts as in > > + * this case driver does not provide a way for masking and > > + * unmasking of individual legacy INTx interrupts. In this case > > + * all interrupts, including legacy INTx are reported via one > > + * shared GIC source and therefore kernel cannot distinguish > > + * which individual legacy INTx was triggered. These interrupts > > + * are shared, so it should not cause any issue. Just > > + * performance penalty as every PCIe interrupt handler needs to > > + * be called when some interrupt is triggered. > > + */ > > This comment applies to current mainline right (ie it describes how > current mainline handles INTx) ? IMO you should split it out in a > separate patch. This above comment describe what happens in if-branch when intx_irq is not set (as written in comment "when intx interrupt was not specified in DT"). You are right that this is also the behavior in the current mainline. I'm not sure if this comment can be split out as support for "intx" interrupt is in this patch. > I understand it is hard but a patch is a logical _change_, this > comment is a change per se, it is a clarification on current > behaviour. Ok, I could try to split this comment into two patches, but part about if-branch comment needs to stay in "this" patch. > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > + unmask |= PCIE_INT_INTX(0) | PCIE_INT_INTX(1) | > > + PCIE_INT_INTX(2) | PCIE_INT_INTX(3); > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > + } > > } > > > > static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, > > @@ -924,6 +948,108 @@ static struct pci_ops mvebu_pcie_ops = { > > .write = mvebu_pcie_wr_conf, > > }; > > > > +static void mvebu_pcie_intx_irq_mask(struct irq_data *d) > > +{ > > + struct mvebu_pcie_port *port = d->domain->host_data; > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > + unsigned long flags; > > + u32 unmask; > > + > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > + unmask &= ~PCIE_INT_INTX(hwirq); > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > +} > > + > > +static void mvebu_pcie_intx_irq_unmask(struct irq_data *d) > > +{ > > + struct mvebu_pcie_port *port = d->domain->host_data; > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > + unsigned long flags; > > + u32 unmask; > > + > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > + unmask |= PCIE_INT_INTX(hwirq); > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > +} > > + > > +static struct irq_chip intx_irq_chip = { > > + .name = "mvebu-INTx", > > + .irq_mask = mvebu_pcie_intx_irq_mask, > > + .irq_unmask = mvebu_pcie_intx_irq_unmask, > > +}; > > + > > +static int mvebu_pcie_intx_irq_map(struct irq_domain *h, > > + unsigned int virq, irq_hw_number_t hwirq) > > +{ > > + struct mvebu_pcie_port *port = h->host_data; > > + > > + irq_set_status_flags(virq, IRQ_LEVEL); > > + irq_set_chip_and_handler(virq, &intx_irq_chip, handle_level_irq); > > + irq_set_chip_data(virq, port); > > + > > + return 0; > > +} > > + > > +static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { > > + .map = mvebu_pcie_intx_irq_map, > > + .xlate = irq_domain_xlate_onecell, > > +}; > > + > > +static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) > > +{ > > + struct device *dev = &port->pcie->pdev->dev; > > + struct device_node *pcie_intc_node; > > + > > + raw_spin_lock_init(&port->irq_lock); > > + > > + pcie_intc_node = of_get_next_child(port->dn, NULL); > > + if (!pcie_intc_node) { > > + dev_err(dev, "No PCIe Intc node found for %s\n", port->name); > > + return -ENODEV; > > + } > > + > > + port->intx_irq_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, > > + &mvebu_pcie_intx_irq_domain_ops, > > + port); > > + of_node_put(pcie_intc_node); > > + if (!port->intx_irq_domain) { > > + dev_err(dev, "Failed to get INTx IRQ domain for %s\n", port->name); > > + return -ENOMEM; > > + } > > + > > + return 0; > > +} > > + > > +static void mvebu_pcie_irq_handler(struct irq_desc *desc) > > +{ > > + struct mvebu_pcie_port *port = irq_desc_get_handler_data(desc); > > + struct irq_chip *chip = irq_desc_get_chip(desc); > > + struct device *dev = &port->pcie->pdev->dev; > > + u32 cause, unmask, status; > > + int i; > > + > > + chained_irq_enter(chip, desc); > > + > > + cause = mvebu_readl(port, PCIE_INT_CAUSE_OFF); > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > + status = cause & unmask; > > + > > + /* Process legacy INTx interrupts */ > > + for (i = 0; i < PCI_NUM_INTX; i++) { > > + if (!(status & PCIE_INT_INTX(i))) > > + continue; > > + > > + if (generic_handle_domain_irq(port->intx_irq_domain, i) == -EINVAL) > > + dev_err_ratelimited(dev, "unexpected INT%c IRQ\n", (char)i+'A'); > > + } > > + > > + chained_irq_exit(chip, desc); > > +} > > + > > static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) > > { > > /* Interrupt support on mvebu emulated bridges is not implemented yet */ > > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > > port->io_attr = -1; > > } > > > > + /* > > + * Old DT bindings do not contain "intx" interrupt > > + * so do not fail probing driver when interrupt does not exist. > > + */ > > + port->intx_irq = of_irq_get_byname(child, "intx"); > > + if (port->intx_irq == -EPROBE_DEFER) { > > + ret = port->intx_irq; > > + goto err; > > + } > > + if (port->intx_irq <= 0) { > > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > > + "%pOF does not contain intx interrupt\n", > > + port->name, child); > > Here you end up with a new warning on existing firmware. Is it > legitimate ? I would remove the dev_warn(). I added this warning in v2 because Marc wanted it. Should I (again) remove it in v3? > Rob certainly has more insightful advice on this. > > Thanks, > Lorenzo > > > + } > > + > > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); > > if (reset_gpio == -EPROBE_DEFER) { > > ret = reset_gpio; > > @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > > for (i = 0; i < pcie->nports; i++) { > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > + int irq = port->intx_irq; > > > > child = port->dn; > > if (!child) > > @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > continue; > > } > > > > + if (irq > 0) { > > + ret = mvebu_pcie_init_irq_domain(port); > > + if (ret) { > > + dev_err(dev, "%s: cannot init irq domain\n", > > + port->name); > > + pci_bridge_emul_cleanup(&port->bridge); > > + devm_iounmap(dev, port->base); > > + port->base = NULL; > > + mvebu_pcie_powerdown(port); > > + continue; > > + } > > + irq_set_chained_handler_and_data(irq, > > + mvebu_pcie_irq_handler, > > + port); > > + } > > + > > /* > > * PCIe topology exported by mvebu hw is quite complicated. In > > * reality has something like N fully independent host bridges > > @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > > for (i = 0; i < pcie->nports; i++) { > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > + int irq = port->intx_irq; > > > > if (!port->base) > > continue; > > @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > mvebu_writel(port, cmd, PCIE_CMD_OFF); > > > > /* Mask all interrupt sources. */ > > - mvebu_writel(port, 0, PCIE_MASK_OFF); > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > + > > + /* Clear all interrupt causes. */ > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > + > > + if (irq > 0) > > + irq_set_chained_handler_and_data(irq, NULL, NULL); > > + > > + /* Remove IRQ domains. */ > > + if (port->intx_irq_domain) > > + irq_domain_remove(port->intx_irq_domain); > > > > /* Free config space for emulated root bridge. */ > > pci_bridge_emul_cleanup(&port->bridge); > > -- > > 2.20.1 > >
On Fri, Feb 11, 2022 at 06:52:02PM +0100, Pali Rohár wrote: [...] > > > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > > > port->io_attr = -1; > > > } > > > > > > + /* > > > + * Old DT bindings do not contain "intx" interrupt > > > + * so do not fail probing driver when interrupt does not exist. > > > + */ > > > + port->intx_irq = of_irq_get_byname(child, "intx"); > > > + if (port->intx_irq == -EPROBE_DEFER) { > > > + ret = port->intx_irq; > > > + goto err; > > > + } > > > + if (port->intx_irq <= 0) { > > > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > > > + "%pOF does not contain intx interrupt\n", > > > + port->name, child); > > > > Here you end up with a new warning on existing firmware. Is it > > legitimate ? I would remove the dev_warn(). > > I added this warning in v2 because Marc wanted it. > > Should I (again) remove it in v3? No, I asked a question and gave an opinion, I appreciate Marc's concern so leave it (ie not everyone running a new kernel with new warnings on existing firmware would be happy - maybe it is a good way of forcing a firmware upgrade, you will tell me). Lorenzo > > Rob certainly has more insightful advice on this. > > > > Thanks, > > Lorenzo > > > > > + } > > > + > > > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); > > > if (reset_gpio == -EPROBE_DEFER) { > > > ret = reset_gpio; > > > @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > child = port->dn; > > > if (!child) > > > @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > continue; > > > } > > > > > > + if (irq > 0) { > > > + ret = mvebu_pcie_init_irq_domain(port); > > > + if (ret) { > > > + dev_err(dev, "%s: cannot init irq domain\n", > > > + port->name); > > > + pci_bridge_emul_cleanup(&port->bridge); > > > + devm_iounmap(dev, port->base); > > > + port->base = NULL; > > > + mvebu_pcie_powerdown(port); > > > + continue; > > > + } > > > + irq_set_chained_handler_and_data(irq, > > > + mvebu_pcie_irq_handler, > > > + port); > > > + } > > > + > > > /* > > > * PCIe topology exported by mvebu hw is quite complicated. In > > > * reality has something like N fully independent host bridges > > > @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > if (!port->base) > > > continue; > > > @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > mvebu_writel(port, cmd, PCIE_CMD_OFF); > > > > > > /* Mask all interrupt sources. */ > > > - mvebu_writel(port, 0, PCIE_MASK_OFF); > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > + > > > + /* Clear all interrupt causes. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > + > > > + if (irq > 0) > > > + irq_set_chained_handler_and_data(irq, NULL, NULL); > > > + > > > + /* Remove IRQ domains. */ > > > + if (port->intx_irq_domain) > > > + irq_domain_remove(port->intx_irq_domain); > > > > > > /* Free config space for emulated root bridge. */ > > > pci_bridge_emul_cleanup(&port->bridge); > > > -- > > > 2.20.1 > > >
On Fri, 11 Feb 2022 18:21:37 +0000, Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> wrote: > > On Fri, Feb 11, 2022 at 06:52:02PM +0100, Pali Rohár wrote: > > [...] > > > > > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > > > > port->io_attr = -1; > > > > } > > > > > > > > + /* > > > > + * Old DT bindings do not contain "intx" interrupt > > > > + * so do not fail probing driver when interrupt does not exist. > > > > + */ > > > > + port->intx_irq = of_irq_get_byname(child, "intx"); > > > > + if (port->intx_irq == -EPROBE_DEFER) { > > > > + ret = port->intx_irq; > > > > + goto err; > > > > + } > > > > + if (port->intx_irq <= 0) { > > > > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > > > > + "%pOF does not contain intx interrupt\n", > > > > + port->name, child); > > > > > > Here you end up with a new warning on existing firmware. Is it > > > legitimate ? I would remove the dev_warn(). > > > > I added this warning in v2 because Marc wanted it. > > > > Should I (again) remove it in v3? > > No, I asked a question and gave an opinion, I appreciate Marc's concern > so leave it (ie not everyone running a new kernel with new warnings on > existing firmware would be happy - maybe it is a good way of forcing a > firmware upgrade, you will tell me). My concern is that short of being able to mask these interrupts, it is possible for a device to assert an interrupt that no driver handles, and the kernel spurious interrupt detector won't be able to shut it up. At this stage, the machine is totally dead (screaming *level* interrupt). The dev_warn() could toned down to a dev_warn_once() though. M.
On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > This adds support for legacy INTx interrupts received from other PCIe > > > devices and which are reported by a new INTx irq chip. > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > interrupts. > > > > > > Note that for this support, device tree files has to be properly adjusted > > > to provide "interrupts" or "interrupts-extended" property with intx > > > interrupt source, "interrupt-names" property with "intx" string and also > > > 'interrupt-controller' subnode must be defined. > > > > > > If device tree files do not provide these nodes then driver would work as > > > before. > > > > Nit: this information is not useful. DT rules are written in DT > > bindings, not in kernel commit logs. All I am saying is that firmware > > developers should not have to read this log to write firmware. > > It was not intended for firmware developers, but for reviewers of this > patch to understand, what is happening in code and that with old DT > files this patch does not change driver behavior (= work as before). > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > --- > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > --- a/drivers/pci/controller/pci-mvebu.c > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > @@ -54,9 +54,10 @@ > > > PCIE_CONF_ADDR_EN) > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > Nit: I understand it is tempting but here you are redefining or better > > giving a proper label to a register. Separate patch please. > > Ok! > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > #define PCIE_INT_PM_PME BIT(28) > > > -#define PCIE_MASK_OFF 0x1910 > > > > See above. > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > #define PCIE_CTRL_OFF 0x1a00 > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > struct mvebu_pcie_window iowin; > > > u32 saved_pcie_stat; > > > struct resource regs; > > > + struct irq_domain *intx_irq_domain; > > > + raw_spinlock_t irq_lock; > > > + int intx_irq; > > > }; > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > { > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > mvebu_pcie_setup_wins(port); > > > > > > - /* Enable interrupt lines A-D. */ > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > + /* Mask all interrupt sources. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > + > > > + /* Clear all interrupt causes. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > + > > > + if (port->intx_irq <= 0) { > > > + /* > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > + * this case driver does not provide a way for masking and > > > + * unmasking of individual legacy INTx interrupts. In this case > > > + * all interrupts, including legacy INTx are reported via one > > > + * shared GIC source and therefore kernel cannot distinguish > > > + * which individual legacy INTx was triggered. These interrupts > > > + * are shared, so it should not cause any issue. Just > > > + * performance penalty as every PCIe interrupt handler needs to > > > + * be called when some interrupt is triggered. > > > + */ > > > > This comment applies to current mainline right (ie it describes how > > current mainline handles INTx) ? IMO you should split it out in a > > separate patch. > > This above comment describe what happens in if-branch when intx_irq is > not set (as written in comment "when intx interrupt was not specified in > DT"). You are right that this is also the behavior in the current > mainline. > > I'm not sure if this comment can be split out as support for "intx" > interrupt is in this patch. > > > I understand it is hard but a patch is a logical _change_, this > > comment is a change per se, it is a clarification on current > > behaviour. > > Ok, I could try to split this comment into two patches, but part about > if-branch comment needs to stay in "this" patch. I have done it locally. Let me know when I should resend this patch series and I will include into it also these changes. > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask |= PCIE_INT_INTX(0) | PCIE_INT_INTX(1) | > > > + PCIE_INT_INTX(2) | PCIE_INT_INTX(3); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + } > > > } > > > > > > static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, > > > @@ -924,6 +948,108 @@ static struct pci_ops mvebu_pcie_ops = { > > > .write = mvebu_pcie_wr_conf, > > > }; > > > > > > +static void mvebu_pcie_intx_irq_mask(struct irq_data *d) > > > +{ > > > + struct mvebu_pcie_port *port = d->domain->host_data; > > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > > + unsigned long flags; > > > + u32 unmask; > > > + > > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask &= ~PCIE_INT_INTX(hwirq); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > > +} > > > + > > > +static void mvebu_pcie_intx_irq_unmask(struct irq_data *d) > > > +{ > > > + struct mvebu_pcie_port *port = d->domain->host_data; > > > + irq_hw_number_t hwirq = irqd_to_hwirq(d); > > > + unsigned long flags; > > > + u32 unmask; > > > + > > > + raw_spin_lock_irqsave(&port->irq_lock, flags); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + unmask |= PCIE_INT_INTX(hwirq); > > > + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); > > > + raw_spin_unlock_irqrestore(&port->irq_lock, flags); > > > +} > > > + > > > +static struct irq_chip intx_irq_chip = { > > > + .name = "mvebu-INTx", > > > + .irq_mask = mvebu_pcie_intx_irq_mask, > > > + .irq_unmask = mvebu_pcie_intx_irq_unmask, > > > +}; > > > + > > > +static int mvebu_pcie_intx_irq_map(struct irq_domain *h, > > > + unsigned int virq, irq_hw_number_t hwirq) > > > +{ > > > + struct mvebu_pcie_port *port = h->host_data; > > > + > > > + irq_set_status_flags(virq, IRQ_LEVEL); > > > + irq_set_chip_and_handler(virq, &intx_irq_chip, handle_level_irq); > > > + irq_set_chip_data(virq, port); > > > + > > > + return 0; > > > +} > > > + > > > +static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { > > > + .map = mvebu_pcie_intx_irq_map, > > > + .xlate = irq_domain_xlate_onecell, > > > +}; > > > + > > > +static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) > > > +{ > > > + struct device *dev = &port->pcie->pdev->dev; > > > + struct device_node *pcie_intc_node; > > > + > > > + raw_spin_lock_init(&port->irq_lock); > > > + > > > + pcie_intc_node = of_get_next_child(port->dn, NULL); > > > + if (!pcie_intc_node) { > > > + dev_err(dev, "No PCIe Intc node found for %s\n", port->name); > > > + return -ENODEV; > > > + } > > > + > > > + port->intx_irq_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, > > > + &mvebu_pcie_intx_irq_domain_ops, > > > + port); > > > + of_node_put(pcie_intc_node); > > > + if (!port->intx_irq_domain) { > > > + dev_err(dev, "Failed to get INTx IRQ domain for %s\n", port->name); > > > + return -ENOMEM; > > > + } > > > + > > > + return 0; > > > +} > > > + > > > +static void mvebu_pcie_irq_handler(struct irq_desc *desc) > > > +{ > > > + struct mvebu_pcie_port *port = irq_desc_get_handler_data(desc); > > > + struct irq_chip *chip = irq_desc_get_chip(desc); > > > + struct device *dev = &port->pcie->pdev->dev; > > > + u32 cause, unmask, status; > > > + int i; > > > + > > > + chained_irq_enter(chip, desc); > > > + > > > + cause = mvebu_readl(port, PCIE_INT_CAUSE_OFF); > > > + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); > > > + status = cause & unmask; > > > + > > > + /* Process legacy INTx interrupts */ > > > + for (i = 0; i < PCI_NUM_INTX; i++) { > > > + if (!(status & PCIE_INT_INTX(i))) > > > + continue; > > > + > > > + if (generic_handle_domain_irq(port->intx_irq_domain, i) == -EINVAL) > > > + dev_err_ratelimited(dev, "unexpected INT%c IRQ\n", (char)i+'A'); > > > + } > > > + > > > + chained_irq_exit(chip, desc); > > > +} > > > + > > > static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) > > > { > > > /* Interrupt support on mvebu emulated bridges is not implemented yet */ > > > @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, > > > port->io_attr = -1; > > > } > > > > > > + /* > > > + * Old DT bindings do not contain "intx" interrupt > > > + * so do not fail probing driver when interrupt does not exist. > > > + */ > > > + port->intx_irq = of_irq_get_byname(child, "intx"); > > > + if (port->intx_irq == -EPROBE_DEFER) { > > > + ret = port->intx_irq; > > > + goto err; > > > + } > > > + if (port->intx_irq <= 0) { > > > + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " > > > + "%pOF does not contain intx interrupt\n", > > > + port->name, child); > > > > Here you end up with a new warning on existing firmware. Is it > > legitimate ? I would remove the dev_warn(). > > I added this warning in v2 because Marc wanted it. > > Should I (again) remove it in v3? > > > Rob certainly has more insightful advice on this. > > > > Thanks, > > Lorenzo > > > > > + } > > > + > > > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); > > > if (reset_gpio == -EPROBE_DEFER) { > > > ret = reset_gpio; > > > @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > child = port->dn; > > > if (!child) > > > @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) > > > continue; > > > } > > > > > > + if (irq > 0) { > > > + ret = mvebu_pcie_init_irq_domain(port); > > > + if (ret) { > > > + dev_err(dev, "%s: cannot init irq domain\n", > > > + port->name); > > > + pci_bridge_emul_cleanup(&port->bridge); > > > + devm_iounmap(dev, port->base); > > > + port->base = NULL; > > > + mvebu_pcie_powerdown(port); > > > + continue; > > > + } > > > + irq_set_chained_handler_and_data(irq, > > > + mvebu_pcie_irq_handler, > > > + port); > > > + } > > > + > > > /* > > > * PCIe topology exported by mvebu hw is quite complicated. In > > > * reality has something like N fully independent host bridges > > > @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > > > > for (i = 0; i < pcie->nports; i++) { > > > struct mvebu_pcie_port *port = &pcie->ports[i]; > > > + int irq = port->intx_irq; > > > > > > if (!port->base) > > > continue; > > > @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) > > > mvebu_writel(port, cmd, PCIE_CMD_OFF); > > > > > > /* Mask all interrupt sources. */ > > > - mvebu_writel(port, 0, PCIE_MASK_OFF); > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > + > > > + /* Clear all interrupt causes. */ > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > + > > > + if (irq > 0) > > > + irq_set_chained_handler_and_data(irq, NULL, NULL); > > > + > > > + /* Remove IRQ domains. */ > > > + if (port->intx_irq_domain) > > > + irq_domain_remove(port->intx_irq_domain); > > > > > > /* Free config space for emulated root bridge. */ > > > pci_bridge_emul_cleanup(&port->bridge); > > > -- > > > 2.20.1 > > >
On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > interrupts. > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > before. > > > > > > Nit: this information is not useful. DT rules are written in DT > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > developers should not have to read this log to write firmware. > > > > It was not intended for firmware developers, but for reviewers of this > > patch to understand, what is happening in code and that with old DT > > files this patch does not change driver behavior (= work as before). > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > --- > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > @@ -54,9 +54,10 @@ > > > > PCIE_CONF_ADDR_EN) > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > giving a proper label to a register. Separate patch please. > > > > Ok! > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > #define PCIE_INT_PM_PME BIT(28) > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > See above. > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > struct mvebu_pcie_window iowin; > > > > u32 saved_pcie_stat; > > > > struct resource regs; > > > > + struct irq_domain *intx_irq_domain; > > > > + raw_spinlock_t irq_lock; > > > > + int intx_irq; > > > > }; > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > { > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > mvebu_pcie_setup_wins(port); > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > + /* Mask all interrupt sources. */ > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > + > > > > + /* Clear all interrupt causes. */ > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > + > > > > + if (port->intx_irq <= 0) { > > > > + /* > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > + * this case driver does not provide a way for masking and > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > + * all interrupts, including legacy INTx are reported via one > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > + * which individual legacy INTx was triggered. These interrupts > > > > + * are shared, so it should not cause any issue. Just > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > + * be called when some interrupt is triggered. > > > > + */ > > > > > > This comment applies to current mainline right (ie it describes how > > > current mainline handles INTx) ? IMO you should split it out in a > > > separate patch. > > > > This above comment describe what happens in if-branch when intx_irq is > > not set (as written in comment "when intx interrupt was not specified in > > DT"). You are right that this is also the behavior in the current > > mainline. > > > > I'm not sure if this comment can be split out as support for "intx" > > interrupt is in this patch. > > > > > I understand it is hard but a patch is a logical _change_, this > > > comment is a change per se, it is a clarification on current > > > behaviour. > > > > Ok, I could try to split this comment into two patches, but part about > > if-branch comment needs to stay in "this" patch. > > I have done it locally. > > Let me know when I should resend this patch series and I will include > into it also these changes. Hi, yes please resend it and I will merge it. Thanks, Lorenzo
On Tuesday 22 February 2022 10:21:06 Lorenzo Pieralisi wrote: > On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > > interrupts. > > > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > > before. > > > > > > > > Nit: this information is not useful. DT rules are written in DT > > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > > developers should not have to read this log to write firmware. > > > > > > It was not intended for firmware developers, but for reviewers of this > > > patch to understand, what is happening in code and that with old DT > > > files this patch does not change driver behavior (= work as before). > > > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > > --- > > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > > @@ -54,9 +54,10 @@ > > > > > PCIE_CONF_ADDR_EN) > > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > > giving a proper label to a register. Separate patch please. > > > > > > Ok! > > > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > > #define PCIE_INT_PM_PME BIT(28) > > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > > > See above. > > > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > > struct mvebu_pcie_window iowin; > > > > > u32 saved_pcie_stat; > > > > > struct resource regs; > > > > > + struct irq_domain *intx_irq_domain; > > > > > + raw_spinlock_t irq_lock; > > > > > + int intx_irq; > > > > > }; > > > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > { > > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > > mvebu_pcie_setup_wins(port); > > > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > > + /* Mask all interrupt sources. */ > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > > + > > > > > + /* Clear all interrupt causes. */ > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > > + > > > > > + if (port->intx_irq <= 0) { > > > > > + /* > > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > > + * this case driver does not provide a way for masking and > > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > > + * all interrupts, including legacy INTx are reported via one > > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > > + * which individual legacy INTx was triggered. These interrupts > > > > > + * are shared, so it should not cause any issue. Just > > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > > + * be called when some interrupt is triggered. > > > > > + */ > > > > > > > > This comment applies to current mainline right (ie it describes how > > > > current mainline handles INTx) ? IMO you should split it out in a > > > > separate patch. > > > > > > This above comment describe what happens in if-branch when intx_irq is > > > not set (as written in comment "when intx interrupt was not specified in > > > DT"). You are right that this is also the behavior in the current > > > mainline. > > > > > > I'm not sure if this comment can be split out as support for "intx" > > > interrupt is in this patch. > > > > > > > I understand it is hard but a patch is a logical _change_, this > > > > comment is a change per se, it is a clarification on current > > > > behaviour. > > > > > > Ok, I could try to split this comment into two patches, but part about > > > if-branch comment needs to stay in "this" patch. > > > > I have done it locally. > > > > Let me know when I should resend this patch series and I will include > > into it also these changes. > > Hi, > > yes please resend it and I will merge it. Done! https://lore.kernel.org/linux-pci/20220222104625.28461-1-pali@kernel.org/T/#u > > Thanks, > Lorenzo
On Tue, Feb 22, 2022 at 11:51:29AM +0100, Pali Rohár wrote: > On Tuesday 22 February 2022 10:21:06 Lorenzo Pieralisi wrote: > > On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > > > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > > > interrupts. > > > > > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > > > before. > > > > > > > > > > Nit: this information is not useful. DT rules are written in DT > > > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > > > developers should not have to read this log to write firmware. > > > > > > > > It was not intended for firmware developers, but for reviewers of this > > > > patch to understand, what is happening in code and that with old DT > > > > files this patch does not change driver behavior (= work as before). > > > > > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > > > --- > > > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > > > @@ -54,9 +54,10 @@ > > > > > > PCIE_CONF_ADDR_EN) > > > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > > > giving a proper label to a register. Separate patch please. > > > > > > > > Ok! > > > > > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > > > #define PCIE_INT_PM_PME BIT(28) > > > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > > > > > See above. > > > > > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > > > struct mvebu_pcie_window iowin; > > > > > > u32 saved_pcie_stat; > > > > > > struct resource regs; > > > > > > + struct irq_domain *intx_irq_domain; > > > > > > + raw_spinlock_t irq_lock; > > > > > > + int intx_irq; > > > > > > }; > > > > > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > { > > > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > > > mvebu_pcie_setup_wins(port); > > > > > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > > > + /* Mask all interrupt sources. */ > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > > > + > > > > > > + /* Clear all interrupt causes. */ > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > > > + > > > > > > + if (port->intx_irq <= 0) { > > > > > > + /* > > > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > > > + * this case driver does not provide a way for masking and > > > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > > > + * all interrupts, including legacy INTx are reported via one > > > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > > > + * which individual legacy INTx was triggered. These interrupts > > > > > > + * are shared, so it should not cause any issue. Just > > > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > > > + * be called when some interrupt is triggered. > > > > > > + */ > > > > > > > > > > This comment applies to current mainline right (ie it describes how > > > > > current mainline handles INTx) ? IMO you should split it out in a > > > > > separate patch. > > > > > > > > This above comment describe what happens in if-branch when intx_irq is > > > > not set (as written in comment "when intx interrupt was not specified in > > > > DT"). You are right that this is also the behavior in the current > > > > mainline. > > > > > > > > I'm not sure if this comment can be split out as support for "intx" > > > > interrupt is in this patch. > > > > > > > > > I understand it is hard but a patch is a logical _change_, this > > > > > comment is a change per se, it is a clarification on current > > > > > behaviour. > > > > > > > > Ok, I could try to split this comment into two patches, but part about > > > > if-branch comment needs to stay in "this" patch. > > > > > > I have done it locally. > > > > > > Let me know when I should resend this patch series and I will include > > > into it also these changes. > > > > Hi, > > > > yes please resend it and I will merge it. > > Done! > https://lore.kernel.org/linux-pci/20220222104625.28461-1-pali@kernel.org/T/#u Can you rebase it please on top of my pci/mvebu branch ? https://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/ Forgive me, I forgot to mention that, thanks. Lorenzo
On Tuesday 22 February 2022 15:24:09 Lorenzo Pieralisi wrote: > On Tue, Feb 22, 2022 at 11:51:29AM +0100, Pali Rohár wrote: > > On Tuesday 22 February 2022 10:21:06 Lorenzo Pieralisi wrote: > > > On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > > > > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > > > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > > > > interrupts. > > > > > > > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > > > > before. > > > > > > > > > > > > Nit: this information is not useful. DT rules are written in DT > > > > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > > > > developers should not have to read this log to write firmware. > > > > > > > > > > It was not intended for firmware developers, but for reviewers of this > > > > > patch to understand, what is happening in code and that with old DT > > > > > files this patch does not change driver behavior (= work as before). > > > > > > > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > > > > --- > > > > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > > > > @@ -54,9 +54,10 @@ > > > > > > > PCIE_CONF_ADDR_EN) > > > > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > > > > giving a proper label to a register. Separate patch please. > > > > > > > > > > Ok! > > > > > > > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > > > > #define PCIE_INT_PM_PME BIT(28) > > > > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > > > > > > > See above. > > > > > > > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > > > > struct mvebu_pcie_window iowin; > > > > > > > u32 saved_pcie_stat; > > > > > > > struct resource regs; > > > > > > > + struct irq_domain *intx_irq_domain; > > > > > > > + raw_spinlock_t irq_lock; > > > > > > > + int intx_irq; > > > > > > > }; > > > > > > > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > { > > > > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > > > > mvebu_pcie_setup_wins(port); > > > > > > > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > > > > + /* Mask all interrupt sources. */ > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > > > > + > > > > > > > + /* Clear all interrupt causes. */ > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > > > > + > > > > > > > + if (port->intx_irq <= 0) { > > > > > > > + /* > > > > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > > > > + * this case driver does not provide a way for masking and > > > > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > > > > + * all interrupts, including legacy INTx are reported via one > > > > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > > > > + * which individual legacy INTx was triggered. These interrupts > > > > > > > + * are shared, so it should not cause any issue. Just > > > > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > > > > + * be called when some interrupt is triggered. > > > > > > > + */ > > > > > > > > > > > > This comment applies to current mainline right (ie it describes how > > > > > > current mainline handles INTx) ? IMO you should split it out in a > > > > > > separate patch. > > > > > > > > > > This above comment describe what happens in if-branch when intx_irq is > > > > > not set (as written in comment "when intx interrupt was not specified in > > > > > DT"). You are right that this is also the behavior in the current > > > > > mainline. > > > > > > > > > > I'm not sure if this comment can be split out as support for "intx" > > > > > interrupt is in this patch. > > > > > > > > > > > I understand it is hard but a patch is a logical _change_, this > > > > > > comment is a change per se, it is a clarification on current > > > > > > behaviour. > > > > > > > > > > Ok, I could try to split this comment into two patches, but part about > > > > > if-branch comment needs to stay in "this" patch. > > > > > > > > I have done it locally. > > > > > > > > Let me know when I should resend this patch series and I will include > > > > into it also these changes. > > > > > > Hi, > > > > > > yes please resend it and I will merge it. > > > > Done! > > https://lore.kernel.org/linux-pci/20220222104625.28461-1-pali@kernel.org/T/#u > > Can you rebase it please on top of my pci/mvebu branch ? > > https://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/ > > Forgive me, I forgot to mention that, thanks. > > Lorenzo Ok! I rebased V3 on top of c3bd7dc553eea5a3595ca3aa0adee9bf83622a1f (pci/mvebu branch in your repo), fixed conflicts and pushed to my git repo https://git.kernel.org/pub/scm/linux/kernel/git/pali/linux.git/ as commit 42402f0cfc362ffb0b7e464f420d6ead342dab2b (lpieralisi-pci-mvebu branch). It is enough? Or do you want me to resend it via emails?
On Tue, Feb 22, 2022 at 04:42:26PM +0100, Pali Rohár wrote: > On Tuesday 22 February 2022 15:24:09 Lorenzo Pieralisi wrote: > > On Tue, Feb 22, 2022 at 11:51:29AM +0100, Pali Rohár wrote: > > > On Tuesday 22 February 2022 10:21:06 Lorenzo Pieralisi wrote: > > > > On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > > > > > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > > > > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > > > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > > > > > interrupts. > > > > > > > > > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > > > > > before. > > > > > > > > > > > > > > Nit: this information is not useful. DT rules are written in DT > > > > > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > > > > > developers should not have to read this log to write firmware. > > > > > > > > > > > > It was not intended for firmware developers, but for reviewers of this > > > > > > patch to understand, what is happening in code and that with old DT > > > > > > files this patch does not change driver behavior (= work as before). > > > > > > > > > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > > > > > --- > > > > > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > > > > > @@ -54,9 +54,10 @@ > > > > > > > > PCIE_CONF_ADDR_EN) > > > > > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > > > > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > > > > > giving a proper label to a register. Separate patch please. > > > > > > > > > > > > Ok! > > > > > > > > > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > > > > > #define PCIE_INT_PM_PME BIT(28) > > > > > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > > > > > > > > > See above. > > > > > > > > > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > > > > > struct mvebu_pcie_window iowin; > > > > > > > > u32 saved_pcie_stat; > > > > > > > > struct resource regs; > > > > > > > > + struct irq_domain *intx_irq_domain; > > > > > > > > + raw_spinlock_t irq_lock; > > > > > > > > + int intx_irq; > > > > > > > > }; > > > > > > > > > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > > { > > > > > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > > > > > mvebu_pcie_setup_wins(port); > > > > > > > > > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > > > > > + /* Mask all interrupt sources. */ > > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > > > > > + > > > > > > > > + /* Clear all interrupt causes. */ > > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > > > > > + > > > > > > > > + if (port->intx_irq <= 0) { > > > > > > > > + /* > > > > > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > > > > > + * this case driver does not provide a way for masking and > > > > > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > > > > > + * all interrupts, including legacy INTx are reported via one > > > > > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > > > > > + * which individual legacy INTx was triggered. These interrupts > > > > > > > > + * are shared, so it should not cause any issue. Just > > > > > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > > > > > + * be called when some interrupt is triggered. > > > > > > > > + */ > > > > > > > > > > > > > > This comment applies to current mainline right (ie it describes how > > > > > > > current mainline handles INTx) ? IMO you should split it out in a > > > > > > > separate patch. > > > > > > > > > > > > This above comment describe what happens in if-branch when intx_irq is > > > > > > not set (as written in comment "when intx interrupt was not specified in > > > > > > DT"). You are right that this is also the behavior in the current > > > > > > mainline. > > > > > > > > > > > > I'm not sure if this comment can be split out as support for "intx" > > > > > > interrupt is in this patch. > > > > > > > > > > > > > I understand it is hard but a patch is a logical _change_, this > > > > > > > comment is a change per se, it is a clarification on current > > > > > > > behaviour. > > > > > > > > > > > > Ok, I could try to split this comment into two patches, but part about > > > > > > if-branch comment needs to stay in "this" patch. > > > > > > > > > > I have done it locally. > > > > > > > > > > Let me know when I should resend this patch series and I will include > > > > > into it also these changes. > > > > > > > > Hi, > > > > > > > > yes please resend it and I will merge it. > > > > > > Done! > > > https://lore.kernel.org/linux-pci/20220222104625.28461-1-pali@kernel.org/T/#u > > > > Can you rebase it please on top of my pci/mvebu branch ? > > > > https://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/ > > > > Forgive me, I forgot to mention that, thanks. > > > > Lorenzo > > Ok! I rebased V3 on top of c3bd7dc553eea5a3595ca3aa0adee9bf83622a1f > (pci/mvebu branch in your repo), fixed conflicts and pushed to my git > repo https://git.kernel.org/pub/scm/linux/kernel/git/pali/linux.git/ > as commit 42402f0cfc362ffb0b7e464f420d6ead342dab2b (lpieralisi-pci-mvebu > branch). It is enough? Or do you want me to resend it via emails? You need to re-send it to linux-pci ML, I only apply patches posted there, sorry for the churn, thanks. Lorenzo
On Tuesday 22 February 2022 15:45:53 Lorenzo Pieralisi wrote: > On Tue, Feb 22, 2022 at 04:42:26PM +0100, Pali Rohár wrote: > > On Tuesday 22 February 2022 15:24:09 Lorenzo Pieralisi wrote: > > > On Tue, Feb 22, 2022 at 11:51:29AM +0100, Pali Rohár wrote: > > > > On Tuesday 22 February 2022 10:21:06 Lorenzo Pieralisi wrote: > > > > > On Thu, Feb 17, 2022 at 12:40:39AM +0100, Pali Rohár wrote: > > > > > > On Friday 11 February 2022 18:52:02 Pali Rohár wrote: > > > > > > > On Friday 11 February 2022 17:19:17 Lorenzo Pieralisi wrote: > > > > > > > > On Wed, Jan 12, 2022 at 04:18:13PM +0100, Pali Rohár wrote: > > > > > > > > > This adds support for legacy INTx interrupts received from other PCIe > > > > > > > > > devices and which are reported by a new INTx irq chip. > > > > > > > > > > > > > > > > > > With this change, kernel can distinguish between INTA, INTB, INTC and INTD > > > > > > > > > interrupts. > > > > > > > > > > > > > > > > > > Note that for this support, device tree files has to be properly adjusted > > > > > > > > > to provide "interrupts" or "interrupts-extended" property with intx > > > > > > > > > interrupt source, "interrupt-names" property with "intx" string and also > > > > > > > > > 'interrupt-controller' subnode must be defined. > > > > > > > > > > > > > > > > > > If device tree files do not provide these nodes then driver would work as > > > > > > > > > before. > > > > > > > > > > > > > > > > Nit: this information is not useful. DT rules are written in DT > > > > > > > > bindings, not in kernel commit logs. All I am saying is that firmware > > > > > > > > developers should not have to read this log to write firmware. > > > > > > > > > > > > > > It was not intended for firmware developers, but for reviewers of this > > > > > > > patch to understand, what is happening in code and that with old DT > > > > > > > files this patch does not change driver behavior (= work as before). > > > > > > > > > > > > > > > > Signed-off-by: Pali Rohár <pali@kernel.org> > > > > > > > > > --- > > > > > > > > > drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- > > > > > > > > > 1 file changed, 177 insertions(+), 8 deletions(-) > > > > > > > > > > > > > > > > > > diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c > > > > > > > > > index 1e90ab888075..dbb6ecb4cb70 100644 > > > > > > > > > --- a/drivers/pci/controller/pci-mvebu.c > > > > > > > > > +++ b/drivers/pci/controller/pci-mvebu.c > > > > > > > > > @@ -54,9 +54,10 @@ > > > > > > > > > PCIE_CONF_ADDR_EN) > > > > > > > > > #define PCIE_CONF_DATA_OFF 0x18fc > > > > > > > > > #define PCIE_INT_CAUSE_OFF 0x1900 > > > > > > > > > +#define PCIE_INT_UNMASK_OFF 0x1910 > > > > > > > > > > > > > > > > Nit: I understand it is tempting but here you are redefining or better > > > > > > > > giving a proper label to a register. Separate patch please. > > > > > > > > > > > > > > Ok! > > > > > > > > > > > > > > > > +#define PCIE_INT_INTX(i) BIT(24+i) > > > > > > > > > #define PCIE_INT_PM_PME BIT(28) > > > > > > > > > -#define PCIE_MASK_OFF 0x1910 > > > > > > > > > > > > > > > > See above. > > > > > > > > > > > > > > > > > -#define PCIE_MASK_ENABLE_INTS 0x0f000000 > > > > > > > > > +#define PCIE_INT_ALL_MASK GENMASK(31, 0) > > > > > > > > > #define PCIE_CTRL_OFF 0x1a00 > > > > > > > > > #define PCIE_CTRL_X1_MODE 0x0001 > > > > > > > > > #define PCIE_CTRL_RC_MODE BIT(1) > > > > > > > > > @@ -110,6 +111,9 @@ struct mvebu_pcie_port { > > > > > > > > > struct mvebu_pcie_window iowin; > > > > > > > > > u32 saved_pcie_stat; > > > > > > > > > struct resource regs; > > > > > > > > > + struct irq_domain *intx_irq_domain; > > > > > > > > > + raw_spinlock_t irq_lock; > > > > > > > > > + int intx_irq; > > > > > > > > > }; > > > > > > > > > > > > > > > > > > static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) > > > > > > > > > @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) > > > > > > > > > > > > > > > > > > static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > > > { > > > > > > > > > - u32 ctrl, lnkcap, cmd, dev_rev, mask; > > > > > > > > > + u32 ctrl, lnkcap, cmd, dev_rev, unmask; > > > > > > > > > > > > > > > > > > /* Setup PCIe controller to Root Complex mode. */ > > > > > > > > > ctrl = mvebu_readl(port, PCIE_CTRL_OFF); > > > > > > > > > @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) > > > > > > > > > /* Point PCIe unit MBUS decode windows to DRAM space. */ > > > > > > > > > mvebu_pcie_setup_wins(port); > > > > > > > > > > > > > > > > > > - /* Enable interrupt lines A-D. */ > > > > > > > > > - mask = mvebu_readl(port, PCIE_MASK_OFF); > > > > > > > > > - mask |= PCIE_MASK_ENABLE_INTS; > > > > > > > > > - mvebu_writel(port, mask, PCIE_MASK_OFF); > > > > > > > > > + /* Mask all interrupt sources. */ > > > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); > > > > > > > > > + > > > > > > > > > + /* Clear all interrupt causes. */ > > > > > > > > > + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); > > > > > > > > > + > > > > > > > > > + if (port->intx_irq <= 0) { > > > > > > > > > + /* > > > > > > > > > + * When neither "summary" interrupt, nor "intx" interrupt was > > > > > > > > > + * specified in DT then unmask all legacy INTx interrupts as in > > > > > > > > > + * this case driver does not provide a way for masking and > > > > > > > > > + * unmasking of individual legacy INTx interrupts. In this case > > > > > > > > > + * all interrupts, including legacy INTx are reported via one > > > > > > > > > + * shared GIC source and therefore kernel cannot distinguish > > > > > > > > > + * which individual legacy INTx was triggered. These interrupts > > > > > > > > > + * are shared, so it should not cause any issue. Just > > > > > > > > > + * performance penalty as every PCIe interrupt handler needs to > > > > > > > > > + * be called when some interrupt is triggered. > > > > > > > > > + */ > > > > > > > > > > > > > > > > This comment applies to current mainline right (ie it describes how > > > > > > > > current mainline handles INTx) ? IMO you should split it out in a > > > > > > > > separate patch. > > > > > > > > > > > > > > This above comment describe what happens in if-branch when intx_irq is > > > > > > > not set (as written in comment "when intx interrupt was not specified in > > > > > > > DT"). You are right that this is also the behavior in the current > > > > > > > mainline. > > > > > > > > > > > > > > I'm not sure if this comment can be split out as support for "intx" > > > > > > > interrupt is in this patch. > > > > > > > > > > > > > > > I understand it is hard but a patch is a logical _change_, this > > > > > > > > comment is a change per se, it is a clarification on current > > > > > > > > behaviour. > > > > > > > > > > > > > > Ok, I could try to split this comment into two patches, but part about > > > > > > > if-branch comment needs to stay in "this" patch. > > > > > > > > > > > > I have done it locally. > > > > > > > > > > > > Let me know when I should resend this patch series and I will include > > > > > > into it also these changes. > > > > > > > > > > Hi, > > > > > > > > > > yes please resend it and I will merge it. > > > > > > > > Done! > > > > https://lore.kernel.org/linux-pci/20220222104625.28461-1-pali@kernel.org/T/#u > > > > > > Can you rebase it please on top of my pci/mvebu branch ? > > > > > > https://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/ > > > > > > Forgive me, I forgot to mention that, thanks. > > > > > > Lorenzo > > > > Ok! I rebased V3 on top of c3bd7dc553eea5a3595ca3aa0adee9bf83622a1f > > (pci/mvebu branch in your repo), fixed conflicts and pushed to my git > > repo https://git.kernel.org/pub/scm/linux/kernel/git/pali/linux.git/ > > as commit 42402f0cfc362ffb0b7e464f420d6ead342dab2b (lpieralisi-pci-mvebu > > branch). It is enough? Or do you want me to resend it via emails? > > You need to re-send it to linux-pci ML, I only apply patches posted > there, sorry for the churn, thanks. > > Lorenzo Done! https://lore.kernel.org/linux-pci/20220222155030.988-1-pali@kernel.org/T/#u
diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c index 1e90ab888075..dbb6ecb4cb70 100644 --- a/drivers/pci/controller/pci-mvebu.c +++ b/drivers/pci/controller/pci-mvebu.c @@ -54,9 +54,10 @@ PCIE_CONF_ADDR_EN) #define PCIE_CONF_DATA_OFF 0x18fc #define PCIE_INT_CAUSE_OFF 0x1900 +#define PCIE_INT_UNMASK_OFF 0x1910 +#define PCIE_INT_INTX(i) BIT(24+i) #define PCIE_INT_PM_PME BIT(28) -#define PCIE_MASK_OFF 0x1910 -#define PCIE_MASK_ENABLE_INTS 0x0f000000 +#define PCIE_INT_ALL_MASK GENMASK(31, 0) #define PCIE_CTRL_OFF 0x1a00 #define PCIE_CTRL_X1_MODE 0x0001 #define PCIE_CTRL_RC_MODE BIT(1) @@ -110,6 +111,9 @@ struct mvebu_pcie_port { struct mvebu_pcie_window iowin; u32 saved_pcie_stat; struct resource regs; + struct irq_domain *intx_irq_domain; + raw_spinlock_t irq_lock; + int intx_irq; }; static inline void mvebu_writel(struct mvebu_pcie_port *port, u32 val, u32 reg) @@ -235,7 +239,7 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) { - u32 ctrl, lnkcap, cmd, dev_rev, mask; + u32 ctrl, lnkcap, cmd, dev_rev, unmask; /* Setup PCIe controller to Root Complex mode. */ ctrl = mvebu_readl(port, PCIE_CTRL_OFF); @@ -288,10 +292,30 @@ static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) /* Point PCIe unit MBUS decode windows to DRAM space. */ mvebu_pcie_setup_wins(port); - /* Enable interrupt lines A-D. */ - mask = mvebu_readl(port, PCIE_MASK_OFF); - mask |= PCIE_MASK_ENABLE_INTS; - mvebu_writel(port, mask, PCIE_MASK_OFF); + /* Mask all interrupt sources. */ + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); + + /* Clear all interrupt causes. */ + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); + + if (port->intx_irq <= 0) { + /* + * When neither "summary" interrupt, nor "intx" interrupt was + * specified in DT then unmask all legacy INTx interrupts as in + * this case driver does not provide a way for masking and + * unmasking of individual legacy INTx interrupts. In this case + * all interrupts, including legacy INTx are reported via one + * shared GIC source and therefore kernel cannot distinguish + * which individual legacy INTx was triggered. These interrupts + * are shared, so it should not cause any issue. Just + * performance penalty as every PCIe interrupt handler needs to + * be called when some interrupt is triggered. + */ + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); + unmask |= PCIE_INT_INTX(0) | PCIE_INT_INTX(1) | + PCIE_INT_INTX(2) | PCIE_INT_INTX(3); + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); + } } static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, @@ -924,6 +948,108 @@ static struct pci_ops mvebu_pcie_ops = { .write = mvebu_pcie_wr_conf, }; +static void mvebu_pcie_intx_irq_mask(struct irq_data *d) +{ + struct mvebu_pcie_port *port = d->domain->host_data; + irq_hw_number_t hwirq = irqd_to_hwirq(d); + unsigned long flags; + u32 unmask; + + raw_spin_lock_irqsave(&port->irq_lock, flags); + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); + unmask &= ~PCIE_INT_INTX(hwirq); + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); + raw_spin_unlock_irqrestore(&port->irq_lock, flags); +} + +static void mvebu_pcie_intx_irq_unmask(struct irq_data *d) +{ + struct mvebu_pcie_port *port = d->domain->host_data; + irq_hw_number_t hwirq = irqd_to_hwirq(d); + unsigned long flags; + u32 unmask; + + raw_spin_lock_irqsave(&port->irq_lock, flags); + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); + unmask |= PCIE_INT_INTX(hwirq); + mvebu_writel(port, unmask, PCIE_INT_UNMASK_OFF); + raw_spin_unlock_irqrestore(&port->irq_lock, flags); +} + +static struct irq_chip intx_irq_chip = { + .name = "mvebu-INTx", + .irq_mask = mvebu_pcie_intx_irq_mask, + .irq_unmask = mvebu_pcie_intx_irq_unmask, +}; + +static int mvebu_pcie_intx_irq_map(struct irq_domain *h, + unsigned int virq, irq_hw_number_t hwirq) +{ + struct mvebu_pcie_port *port = h->host_data; + + irq_set_status_flags(virq, IRQ_LEVEL); + irq_set_chip_and_handler(virq, &intx_irq_chip, handle_level_irq); + irq_set_chip_data(virq, port); + + return 0; +} + +static const struct irq_domain_ops mvebu_pcie_intx_irq_domain_ops = { + .map = mvebu_pcie_intx_irq_map, + .xlate = irq_domain_xlate_onecell, +}; + +static int mvebu_pcie_init_irq_domain(struct mvebu_pcie_port *port) +{ + struct device *dev = &port->pcie->pdev->dev; + struct device_node *pcie_intc_node; + + raw_spin_lock_init(&port->irq_lock); + + pcie_intc_node = of_get_next_child(port->dn, NULL); + if (!pcie_intc_node) { + dev_err(dev, "No PCIe Intc node found for %s\n", port->name); + return -ENODEV; + } + + port->intx_irq_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX, + &mvebu_pcie_intx_irq_domain_ops, + port); + of_node_put(pcie_intc_node); + if (!port->intx_irq_domain) { + dev_err(dev, "Failed to get INTx IRQ domain for %s\n", port->name); + return -ENOMEM; + } + + return 0; +} + +static void mvebu_pcie_irq_handler(struct irq_desc *desc) +{ + struct mvebu_pcie_port *port = irq_desc_get_handler_data(desc); + struct irq_chip *chip = irq_desc_get_chip(desc); + struct device *dev = &port->pcie->pdev->dev; + u32 cause, unmask, status; + int i; + + chained_irq_enter(chip, desc); + + cause = mvebu_readl(port, PCIE_INT_CAUSE_OFF); + unmask = mvebu_readl(port, PCIE_INT_UNMASK_OFF); + status = cause & unmask; + + /* Process legacy INTx interrupts */ + for (i = 0; i < PCI_NUM_INTX; i++) { + if (!(status & PCIE_INT_INTX(i))) + continue; + + if (generic_handle_domain_irq(port->intx_irq_domain, i) == -EINVAL) + dev_err_ratelimited(dev, "unexpected INT%c IRQ\n", (char)i+'A'); + } + + chained_irq_exit(chip, desc); +} + static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) { /* Interrupt support on mvebu emulated bridges is not implemented yet */ @@ -1121,6 +1247,21 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->io_attr = -1; } + /* + * Old DT bindings do not contain "intx" interrupt + * so do not fail probing driver when interrupt does not exist. + */ + port->intx_irq = of_irq_get_byname(child, "intx"); + if (port->intx_irq == -EPROBE_DEFER) { + ret = port->intx_irq; + goto err; + } + if (port->intx_irq <= 0) { + dev_warn(dev, "%s: legacy INTx interrupts cannot be masked individually, " + "%pOF does not contain intx interrupt\n", + port->name, child); + } + reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags); if (reset_gpio == -EPROBE_DEFER) { ret = reset_gpio; @@ -1317,6 +1458,7 @@ static int mvebu_pcie_probe(struct platform_device *pdev) for (i = 0; i < pcie->nports; i++) { struct mvebu_pcie_port *port = &pcie->ports[i]; + int irq = port->intx_irq; child = port->dn; if (!child) @@ -1344,6 +1486,22 @@ static int mvebu_pcie_probe(struct platform_device *pdev) continue; } + if (irq > 0) { + ret = mvebu_pcie_init_irq_domain(port); + if (ret) { + dev_err(dev, "%s: cannot init irq domain\n", + port->name); + pci_bridge_emul_cleanup(&port->bridge); + devm_iounmap(dev, port->base); + port->base = NULL; + mvebu_pcie_powerdown(port); + continue; + } + irq_set_chained_handler_and_data(irq, + mvebu_pcie_irq_handler, + port); + } + /* * PCIe topology exported by mvebu hw is quite complicated. In * reality has something like N fully independent host bridges @@ -1448,6 +1606,7 @@ static int mvebu_pcie_remove(struct platform_device *pdev) for (i = 0; i < pcie->nports; i++) { struct mvebu_pcie_port *port = &pcie->ports[i]; + int irq = port->intx_irq; if (!port->base) continue; @@ -1458,7 +1617,17 @@ static int mvebu_pcie_remove(struct platform_device *pdev) mvebu_writel(port, cmd, PCIE_CMD_OFF); /* Mask all interrupt sources. */ - mvebu_writel(port, 0, PCIE_MASK_OFF); + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_UNMASK_OFF); + + /* Clear all interrupt causes. */ + mvebu_writel(port, ~PCIE_INT_ALL_MASK, PCIE_INT_CAUSE_OFF); + + if (irq > 0) + irq_set_chained_handler_and_data(irq, NULL, NULL); + + /* Remove IRQ domains. */ + if (port->intx_irq_domain) + irq_domain_remove(port->intx_irq_domain); /* Free config space for emulated root bridge. */ pci_bridge_emul_cleanup(&port->bridge);
This adds support for legacy INTx interrupts received from other PCIe devices and which are reported by a new INTx irq chip. With this change, kernel can distinguish between INTA, INTB, INTC and INTD interrupts. Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with intx interrupt source, "interrupt-names" property with "intx" string and also 'interrupt-controller' subnode must be defined. If device tree files do not provide these nodes then driver would work as before. Signed-off-by: Pali Rohár <pali@kernel.org> --- drivers/pci/controller/pci-mvebu.c | 185 +++++++++++++++++++++++++++-- 1 file changed, 177 insertions(+), 8 deletions(-)