@@ -8,6 +8,7 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/sys_soc.h>
+#include <linux/firmware_bootinfo.h>
static struct {
const char *name;
@@ -74,6 +75,47 @@ static const char *siliconid_to_rev(u32 siliconid)
return "??";
}
+/* Secure Boot Controller register */
+#define SEC_STATUS 0x14
+#define ABR_IMAGE_SOURCE BIT(13)
+#define OTP_PROTECTED BIT(8)
+#define LOW_SEC_KEY BIT(7)
+#define SECURE_BOOT BIT(6)
+#define UART_BOOT BIT(5)
+
+static void __init aspeed_bootinfo_init(void)
+{
+ struct device_node *np;
+ void __iomem *base;
+ struct bootinfo bootinfo = {};
+ u32 reg;
+
+ /* AST2600 only */
+ np = of_find_compatible_node(NULL, NULL, "aspeed,ast2600-sbc");
+ if (!of_device_is_available(np))
+ return;
+
+ base = of_iomap(np, 0);
+ if (!base)
+ of_node_put(np);
+
+ reg = readl(base + SEC_STATUS);
+
+ iounmap(base);
+ of_node_put(np);
+
+ BOOTINFO_SET(bootinfo, abr_image, reg & ABR_IMAGE_SOURCE);
+ BOOTINFO_SET(bootinfo, low_security_key, reg & LOW_SEC_KEY);
+ BOOTINFO_SET(bootinfo, otp_protected, reg & OTP_PROTECTED);
+ BOOTINFO_SET(bootinfo, secure_boot, reg & SECURE_BOOT);
+ /* Invert the bit; as 1 is boot from SPI/eMMC */
+ BOOTINFO_SET(bootinfo, uart_boot, !(reg & UART_BOOT));
+
+ firmware_bootinfo_init(&bootinfo);
+
+ pr_info("AST2600 secure boot %s\n", (reg & SECURE_BOOT) ? "enabled" : "disabled");
+}
+
static int __init aspeed_socinfo_init(void)
{
struct soc_device_attribute *attrs;
@@ -148,6 +190,8 @@ static int __init aspeed_socinfo_init(void)
attrs->revision,
attrs->soc_id);
+ aspeed_bootinfo_init();
+
return 0;
}
-early_initcall(aspeed_socinfo_init);
+subsys_initcall(aspeed_socinfo_init);
This reads out the status of the secure boot controller and exposes it in sysfs using the bootinfo sysfs api. An example on a AST2600A3 QEMU model: # grep -r . /sys/firmware/bootinfo/* /sys/firmware/bootinfo/abr_image:0 /sys/firmware/bootinfo/low_security_key:0 /sys/firmware/bootinfo/otp_protected:0 /sys/firmware/bootinfo/secure_boot:1 /sys/firmware/bootinfo/uart_boot:0 On boot the state of the system according to the secure boot controller will be printed: [ 0.037634] AST2600 secure boot enabled or [ 0.037935] AST2600 secure boot disabled The initialisation is changed from early_initcall to subsys_initcall because we need the firmware_kobj to be initialised, and because there's no requirement to print this information early. Signed-off-by: Joel Stanley <joel@jms.id.au> --- v2: - Rewrite to new bootinfo api - Get rid of unused return values --- drivers/soc/aspeed/aspeed-socinfo.c | 46 ++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-)