diff mbox series

[v2,01/66] ARM: dts: sun8i: v3s: Move the csi1 block to follow address order

Message ID 20220205185429.2278860-2-paul.kocialkowski@bootlin.com (mailing list archive)
State New, archived
Headers show
Series Allwinner A31/A83T MIPI CSI-2 Support and A31 ISP Support | expand

Commit Message

Paul Kocialkowski Feb. 5, 2022, 6:53 p.m. UTC
The csi1 block node was mistakenly added before the gic node, although
its address comes after the gic's. Move the node to its correct
position.

Fixes: 90e048101fa1 ("ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

Comments

Maxime Ripard Feb. 7, 2022, 9:24 a.m. UTC | #1
On Sat, 5 Feb 2022 19:53:24 +0100, Paul Kocialkowski wrote:
> The csi1 block node was mistakenly added before the gic node, although
> its address comes after the gic's. Move the node to its correct
> position.
> 
> 

Applied to sunxi/linux.git (sunxi/dt-for-5.18).

Thanks!
Maxime
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index b30bc1a25ebb..084323d5c61c 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -593,6 +593,17 @@  spi0: spi@1c68000 {
 			#size-cells = <0>;
 		};
 
+		gic: interrupt-controller@1c81000 {
+			compatible = "arm,gic-400";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x2000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
 		csi1: camera@1cb4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
@@ -604,16 +615,5 @@  csi1: camera@1cb4000 {
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
 		};
-
-		gic: interrupt-controller@1c81000 {
-			compatible = "arm,gic-400";
-			reg = <0x01c81000 0x1000>,
-			      <0x01c82000 0x2000>,
-			      <0x01c84000 0x2000>,
-			      <0x01c86000 0x2000>;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-		};
 	};
 };