diff mbox series

[v3,4/6] spi: rockchip: Preset cs-high and clk polarity in setup progress

Message ID 20220216014028.8123-5-jon.lin@rock-chips.com (mailing list archive)
State New, archived
Headers show
Series New support and problem adjustment of SPI rockchip | expand

Commit Message

Jon Lin Feb. 16, 2022, 1:40 a.m. UTC
After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.

Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
---

Changes in v3:
- Support clear the bits of configure bits filed

Changes in v2:
- Limit cs-high presetting to the chip select n <= 1

Changes in v1: None

 drivers/spi/spi-rockchip.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
diff mbox series

Patch

diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c
index 5ecd0692cca1..83da8fdb3c02 100644
--- a/drivers/spi/spi-rockchip.c
+++ b/drivers/spi/spi-rockchip.c
@@ -713,6 +713,29 @@  static bool rockchip_spi_can_dma(struct spi_controller *ctlr,
 	return xfer->len / bytes_per_word >= rs->fifo_len;
 }
 
+static int rockchip_spi_setup(struct spi_device *spi)
+{
+	struct rockchip_spi *rs = spi_controller_get_devdata(spi->controller);
+	u32 cr0;
+
+	pm_runtime_get_sync(rs->dev);
+
+	cr0 = readl_relaxed(rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	cr0 &= ~(0x3 << CR0_SCPH_OFFSET);
+	cr0 |= ((spi->mode & 0x3) << CR0_SCPH_OFFSET);
+	if (spi->mode & SPI_CS_HIGH && spi->chip_select <= 1)
+		cr0 |= BIT(spi->chip_select) << CR0_SOI_OFFSET;
+	else if (spi->chip_select <= 1)
+		cr0 &= ~(BIT(spi->chip_select) << CR0_SOI_OFFSET);
+
+	writel_relaxed(cr0, rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	pm_runtime_put(rs->dev);
+
+	return 0;
+}
+
 static int rockchip_spi_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -840,6 +863,7 @@  static int rockchip_spi_probe(struct platform_device *pdev)
 	ctlr->min_speed_hz = rs->freq / BAUDR_SCKDV_MAX;
 	ctlr->max_speed_hz = min(rs->freq / BAUDR_SCKDV_MIN, MAX_SCLK_OUT);
 
+	ctlr->setup = rockchip_spi_setup;
 	ctlr->set_cs = rockchip_spi_set_cs;
 	ctlr->transfer_one = rockchip_spi_transfer_one;
 	ctlr->max_transfer_size = rockchip_spi_max_transfer_size;