diff mbox series

[v1,3/3] arm64: dts: freescale: add initial support for verdin imx8m plus

Message ID 20220317160122.341484-4-marcel@ziswiler.com (mailing list archive)
State New, archived
Headers show
Series arm64: prepare and add verdin imx8m plus support | expand

Commit Message

Marcel Ziswiler March 17, 2022, 4:01 p.m. UTC
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
a computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional I2C temperature sensor plus an optional
Bluetooth/Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, USB host, eMMC and Ethernet functionality work fine.

[1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plus

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

 arch/arm64/boot/dts/freescale/Makefile        |    4 +
 .../dts/freescale/imx8mp-verdin-dahlia.dtsi   |  125 ++
 .../boot/dts/freescale/imx8mp-verdin-dev.dtsi |   44 +
 .../imx8mp-verdin-nonwifi-dahlia.dts          |   18 +
 .../freescale/imx8mp-verdin-nonwifi-dev.dts   |   18 +
 .../dts/freescale/imx8mp-verdin-nonwifi.dtsi  |   54 +
 .../freescale/imx8mp-verdin-wifi-dahlia.dts   |   18 +
 .../dts/freescale/imx8mp-verdin-wifi-dev.dts  |   18 +
 .../dts/freescale/imx8mp-verdin-wifi.dtsi     |   82 +
 .../boot/dts/freescale/imx8mp-verdin.dtsi     | 1373 +++++++++++++++++
 10 files changed, 1754 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi

Comments

Laurent Pinchart March 22, 2022, 11:02 p.m. UTC | #1
Hi Marcel,

Thank you for the patch.

On Thu, Mar 17, 2022 at 05:01:22PM +0100, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
> a computer on module which can be used on different carrier boards.
> 
> The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
> Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
> 1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
> RX8130 RTC, an optional I2C temperature sensor plus an optional
> Bluetooth/Wi-Fi module.
> 
> Anything that is not self-contained on the module is disabled by
> default.
> 
> The device tree for the Dahlia includes the module's device tree and
> enables the supported peripherals of the carrier board.
> 
> The device tree for the Verdin Development Board includes the module's
> device tree as well as the Dahlia one as it is a superset and supports
> almost all peripherals available.
> 
> So far there is no display functionality supported at all but basic
> console UART, USB host, eMMC and Ethernet functionality work fine.
> 
> [1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plus
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
>  arch/arm64/boot/dts/freescale/Makefile        |    4 +
>  .../dts/freescale/imx8mp-verdin-dahlia.dtsi   |  125 ++
>  .../boot/dts/freescale/imx8mp-verdin-dev.dtsi |   44 +
>  .../imx8mp-verdin-nonwifi-dahlia.dts          |   18 +
>  .../freescale/imx8mp-verdin-nonwifi-dev.dts   |   18 +
>  .../dts/freescale/imx8mp-verdin-nonwifi.dtsi  |   54 +
>  .../freescale/imx8mp-verdin-wifi-dahlia.dts   |   18 +
>  .../dts/freescale/imx8mp-verdin-wifi-dev.dts  |   18 +
>  .../dts/freescale/imx8mp-verdin-wifi.dtsi     |   82 +
>  .../boot/dts/freescale/imx8mp-verdin.dtsi     | 1373 +++++++++++++++++
>  10 files changed, 1754 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi

[snip]

> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> new file mode 100644
> index 000000000000..103d97a3b029
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> @@ -0,0 +1,125 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2022 Toradex
> + */
> +
> +&backlight {
> +	power-supply = <&reg_3p3v>;
> +};
> +
> +/* Verdin SPI_1 */
> +&ecspi1 {
> +	status = "okay";
> +};
> +
> +/* EEPROM on display adapter boards */
> +&eeprom_display_adapter {
> +	status = "okay";
> +};
> +
> +/* EEPROM on Verdin Development board */
> +&eeprom_carrier_board {
> +	status = "okay";
> +};
> +
> +&eqos {
> +	status = "okay";
> +};
> +
> +&flexcan1 {
> +	status = "okay";
> +};
> +
> +&flexcan2 {
> +	status = "okay";
> +};
> +
> +/* Verdin QSPI_1 */
> +&flexspi {
> +	status = "okay";
> +};
> +
> +/* Current measurement into module VCC */
> +&hwmon {
> +	status = "okay";
> +};
> +
> +&hwmon_temp {
> +	vs-supply = <&reg_1p8v>;
> +	status = "okay";
> +};
> +
> +/* Verdin I2C_2_DSI */
> +&i2c2 {
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +};
> +
> +/* Verdin I2C_1 */
> +&i2c4 {
> +	status = "okay";
> +};
> +
> +/* Verdin PCIE_1 */

Is this comment needed ? Is it a placeholder for future PCIe support ?
If so I'd write

/* TODO: Verdin PCIE_1 */

> +
> +/* Verdin PWM_1 */
> +&pwm1 {
> +	status = "okay";
> +};
> +
> +/* Verdin PWM_2 */
> +&pwm2 {
> +	status = "okay";
> +};
> +
> +/* Verdin PWM_3_DSI */
> +&pwm3 {
> +	status = "okay";
> +};
> +
> +&reg_usdhc2_vmmc {
> +	vin-supply = <&reg_3p3v>;
> +};
> +
> +/* VERDIN I2S_1 */

Same here. By the way, you may want to standardize on Verdin or VERDIN
and not mix both. These comments apply to the other files too.

> +
> +/* Verdin UART_1 */
> +&uart1 {
> +	status = "okay";
> +};
> +
> +/* Verdin UART_2 */
> +&uart2 {
> +	status = "okay";
> +};
> +
> +/* Verdin UART_3, used as the Linux Console */
> +&uart3 {
> +	status = "okay";
> +};
> +
> +/* Verdin USB_1 */
> +&usb3_0 {
> +	status = "okay";
> +};
> +
> +&usb3_phy0 {
> +	status = "okay";
> +};
> +
> +/* Verdin USB_2 */
> +&usb3_1 {
> +	status = "okay";
> +};
> +
> +&usb3_phy1 {
> +	status = "okay";
> +};
> +
> +/* Verdin SD_1 */
> +&usdhc2 {
> +	status = "okay";
> +};

[snip]

> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
> new file mode 100644
> index 000000000000..26d6c2819ee8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
> @@ -0,0 +1,1373 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2022 Toradex
> + */
> +
> +#include "dt-bindings/pwm/pwm.h"
> +#include "imx8mp.dtsi"
> +
> +/ {
> +	chosen {
> +		stdout-path = &uart3;
> +	};
> +
> +	aliases {
> +		/* Ethernet aliases to ensure correct MAC addresses */
> +		ethernet0 = &eqos;
> +		ethernet1 = &fec;

On Dahlia the ethernet connector is routed to the eqos if I'm not
mistaken. On my board U-Boot considers this to be the second ethernet
controller, with the fec being the first one. The mismatch results in
the MAC addresses being swapped between eth0 and eth1 when comparing
U-Boot and Linux. Am I using a too old boot loader, or should the two
ethernet controlls be swapped here ?

> +		rtc0 = &rtc_i2c;
> +		rtc1 = &snvs_rtc;
> +	};

[snip]

With these issues addressed,

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Marcel Ziswiler March 23, 2022, 10:55 a.m. UTC | #2
Hi Laurent

On Wed, 2022-03-23 at 01:02 +0200, Laurent Pinchart wrote:
> Hi Marcel,
> 
> Thank you for the patch.

Thank you for reviewing/testing.

> On Thu, Mar 17, 2022 at 05:01:22PM +0100, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
> > a computer on module which can be used on different carrier boards.
> > 
> > The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
> > Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
> > 1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
> > RX8130 RTC, an optional I2C temperature sensor plus an optional
> > Bluetooth/Wi-Fi module.
> > 
> > Anything that is not self-contained on the module is disabled by
> > default.
> > 
> > The device tree for the Dahlia includes the module's device tree and
> > enables the supported peripherals of the carrier board.
> > 
> > The device tree for the Verdin Development Board includes the module's
> > device tree as well as the Dahlia one as it is a superset and supports
> > almost all peripherals available.
> > 
> > So far there is no display functionality supported at all but basic
> > console UART, USB host, eMMC and Ethernet functionality work fine.
> > 
> > [1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plus
> > 
> > Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > ---
> > 
> >  arch/arm64/boot/dts/freescale/Makefile        |    4 +
> >  .../dts/freescale/imx8mp-verdin-dahlia.dtsi   |  125 ++
> >  .../boot/dts/freescale/imx8mp-verdin-dev.dtsi |   44 +
> >  .../imx8mp-verdin-nonwifi-dahlia.dts          |   18 +
> >  .../freescale/imx8mp-verdin-nonwifi-dev.dts   |   18 +
> >  .../dts/freescale/imx8mp-verdin-nonwifi.dtsi  |   54 +
> >  .../freescale/imx8mp-verdin-wifi-dahlia.dts   |   18 +
> >  .../dts/freescale/imx8mp-verdin-wifi-dev.dts  |   18 +
> >  .../dts/freescale/imx8mp-verdin-wifi.dtsi     |   82 +
> >  .../boot/dts/freescale/imx8mp-verdin.dtsi     | 1373 +++++++++++++++++
> >  10 files changed, 1754 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
> 
> [snip]
> 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> > b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> > new file mode 100644
> > index 000000000000..103d97a3b029
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> > @@ -0,0 +1,125 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2022 Toradex
> > + */
> > +
> > +&backlight {
> > +       power-supply = <&reg_3p3v>;
> > +};
> > +
> > +/* Verdin SPI_1 */
> > +&ecspi1 {
> > +       status = "okay";
> > +};
> > +
> > +/* EEPROM on display adapter boards */
> > +&eeprom_display_adapter {
> > +       status = "okay";
> > +};
> > +
> > +/* EEPROM on Verdin Development board */
> > +&eeprom_carrier_board {
> > +       status = "okay";
> > +};
> > +
> > +&eqos {
> > +       status = "okay";
> > +};
> > +
> > +&flexcan1 {
> > +       status = "okay";
> > +};
> > +
> > +&flexcan2 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin QSPI_1 */
> > +&flexspi {
> > +       status = "okay";
> > +};
> > +
> > +/* Current measurement into module VCC */
> > +&hwmon {
> > +       status = "okay";
> > +};
> > +
> > +&hwmon_temp {
> > +       vs-supply = <&reg_1p8v>;
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin I2C_2_DSI */
> > +&i2c2 {
> > +       status = "okay";
> > +};
> > +
> > +&i2c3 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin I2C_1 */
> > +&i2c4 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin PCIE_1 */
> 
> Is this comment needed ? Is it a placeholder for future PCIe support ?
> If so I'd write
> 
> /* TODO: Verdin PCIE_1 */

Yes, exactly, let me do as you suggest.

> > +
> > +/* Verdin PWM_1 */
> > +&pwm1 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin PWM_2 */
> > +&pwm2 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin PWM_3_DSI */
> > +&pwm3 {
> > +       status = "okay";
> > +};
> > +
> > +&reg_usdhc2_vmmc {
> > +       vin-supply = <&reg_3p3v>;
> > +};
> > +
> > +/* VERDIN I2S_1 */
> 
> Same here. By the way, you may want to standardize on Verdin or VERDIN
> and not mix both. These comments apply to the other files too.

Yes, let me also add a TODO in front here. Plus yeah, this capitalized variant just slipped our eyes and I will
change them all to regular Verdin. Thanks for spotting this.

> > +
> > +/* Verdin UART_1 */
> > +&uart1 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin UART_2 */
> > +&uart2 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin UART_3, used as the Linux Console */
> > +&uart3 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin USB_1 */
> > +&usb3_0 {
> > +       status = "okay";
> > +};
> > +
> > +&usb3_phy0 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin USB_2 */
> > +&usb3_1 {
> > +       status = "okay";
> > +};
> > +
> > +&usb3_phy1 {
> > +       status = "okay";
> > +};
> > +
> > +/* Verdin SD_1 */
> > +&usdhc2 {
> > +       status = "okay";
> > +};
> 
> [snip]
> 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-
> > verdin.dtsi
> > new file mode 100644
> > index 000000000000..26d6c2819ee8
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
> > @@ -0,0 +1,1373 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2022 Toradex
> > + */
> > +
> > +#include "dt-bindings/pwm/pwm.h"
> > +#include "imx8mp.dtsi"
> > +
> > +/ {
> > +       chosen {
> > +               stdout-path = &uart3;
> > +       };
> > +
> > +       aliases {
> > +               /* Ethernet aliases to ensure correct MAC addresses */
> > +               ethernet0 = &eqos;
> > +               ethernet1 = &fec;
> 
> On Dahlia the ethernet connector is routed to the eqos if I'm not
> mistaken.

Yes, actually the on-module PHY which is what is routed to the RJ-45 on Dahlia uses the EQOS MAC, correct.

> On my board U-Boot considers this to be the second ethernet
> controller, with the fec being the first one.

Yes, however, U-Boot does use the EQOS one as primary MAC as well. This is just how U-Boot does things. There
is no easy way to change the actual instance numbering. Actually just like on Linux really with the one
difference that U-Boot will always show both independent whether or not your carrier board even has the second
PHY or not. This is due to U-Boot doing lazy loading aka not touch any Ethernet hardware unless you actually
run some network commands.

> The mismatch results in
> the MAC addresses being swapped between eth0 and eth1 when comparing
> U-Boot and Linux.

No, this alias should really be what ensures the correct MAC addresses.

> Am I using a too old boot loader, or should the two
> ethernet controlls be swapped here ?

Yes, I guess you might not be using latest mainline U-Boot. I just verified this on my table again having both
the Dahlia and Verdin Development carrier boards available. Please note that on the Verdin Development Board
the primary Ethernet is also called eth1. Unfortunately, changing this naming is also not entirely trivial. But
it really should have the proper MAC address.

Dahlia

U-Boot 2022.04-rc4-00068-g5f68470d69 (Mar 23 2022 - 10:15:46 +0100)

Verdin iMX8MP # echo $ethaddr
00:14:2d:6c:71:64
=> verified with wireshark

root@verdin-imx8mp-07106916:~# ip addr
...
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:14:2d:6c:71:64 brd ff:ff:ff:ff:ff:ff
    inet 192.168.10.239/24 brd 192.168.10.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::214:2dff:fe6c:7164/64 scope link 
       valid_lft forever preferred_lft forever
...

Verdin Developer Board

U-Boot 2022.04-rc4-00068-g5f68470d69 (Mar 23 2022 - 10:15:46 +0100)

Verdin iMX8MP # echo $ethaddr  
00:14:2d:6c:71:64
=> verified with wireshark

root@verdin-imx8mp-07106916:~# uname -a
Linux verdin-imx8mp-07106916 5.17.0-rc8-next-20220317-00003-g695dc7d13c2a #12 SMP PREEMPT Thu Mar 17 16:07:49
CET 2022 aarch64 aarch64 aarch64 GNU/Linux

root@verdin-imx8mp-07106916:~# ip addr
...
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,DYNAMIC,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 00:14:2d:7c:71:64 brd ff:ff:ff:ff:ff:ff
...
5: eth1: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:14:2d:6c:71:64 brd ff:ff:ff:ff:ff:ff
    inet 192.168.10.239/24 brd 192.168.10.255 scope global eth1
       valid_lft forever preferred_lft forever
    inet6 fe80::214:2dff:fe6c:7164/64 scope link 
       valid_lft forever preferred_lft forever
...

> > +               rtc0 = &rtc_i2c;
> > +               rtc1 = &snvs_rtc;
> > +       };
> 
> [snip]
> 
> With these issues addressed,
> 
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Thanks again!

Cheers

Marcel
Laurent Pinchart March 23, 2022, 11:40 a.m. UTC | #3
Hi Marcel,

On Wed, Mar 23, 2022 at 10:55:33AM +0000, Marcel Ziswiler wrote:
> On Wed, 2022-03-23 at 01:02 +0200, Laurent Pinchart wrote:
> > On Thu, Mar 17, 2022 at 05:01:22PM +0100, Marcel Ziswiler wrote:
> > > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > > 
> > > This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
> > > a computer on module which can be used on different carrier boards.
> > > 
> > > The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
> > > Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
> > > 1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
> > > RX8130 RTC, an optional I2C temperature sensor plus an optional
> > > Bluetooth/Wi-Fi module.
> > > 
> > > Anything that is not self-contained on the module is disabled by
> > > default.
> > > 
> > > The device tree for the Dahlia includes the module's device tree and
> > > enables the supported peripherals of the carrier board.
> > > 
> > > The device tree for the Verdin Development Board includes the module's
> > > device tree as well as the Dahlia one as it is a superset and supports
> > > almost all peripherals available.
> > > 
> > > So far there is no display functionality supported at all but basic
> > > console UART, USB host, eMMC and Ethernet functionality work fine.
> > > 
> > > [1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plus
> > > 
> > > Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > > 
> > > ---
> > > 
> > >  arch/arm64/boot/dts/freescale/Makefile        |    4 +
> > >  .../dts/freescale/imx8mp-verdin-dahlia.dtsi   |  125 ++
> > >  .../boot/dts/freescale/imx8mp-verdin-dev.dtsi |   44 +
> > >  .../imx8mp-verdin-nonwifi-dahlia.dts          |   18 +
> > >  .../freescale/imx8mp-verdin-nonwifi-dev.dts   |   18 +
> > >  .../dts/freescale/imx8mp-verdin-nonwifi.dtsi  |   54 +
> > >  .../freescale/imx8mp-verdin-wifi-dahlia.dts   |   18 +
> > >  .../dts/freescale/imx8mp-verdin-wifi-dev.dts  |   18 +
> > >  .../dts/freescale/imx8mp-verdin-wifi.dtsi     |   82 +
> > >  .../boot/dts/freescale/imx8mp-verdin.dtsi     | 1373 +++++++++++++++++
> > >  10 files changed, 1754 insertions(+)
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
> > >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi

[snip]

> > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-
> > > verdin.dtsi
> > > new file mode 100644
> > > index 000000000000..26d6c2819ee8
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
> > > @@ -0,0 +1,1373 @@
> > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > > +/*
> > > + * Copyright 2022 Toradex
> > > + */
> > > +
> > > +#include "dt-bindings/pwm/pwm.h"
> > > +#include "imx8mp.dtsi"
> > > +
> > > +/ {
> > > +       chosen {
> > > +               stdout-path = &uart3;
> > > +       };
> > > +
> > > +       aliases {
> > > +               /* Ethernet aliases to ensure correct MAC addresses */
> > > +               ethernet0 = &eqos;
> > > +               ethernet1 = &fec;
> > 
> > On Dahlia the ethernet connector is routed to the eqos if I'm not
> > mistaken.
> 
> Yes, actually the on-module PHY which is what is routed to the RJ-45 on Dahlia uses the EQOS MAC, correct.
> 
> > On my board U-Boot considers this to be the second ethernet
> > controller, with the fec being the first one.
> 
> Yes, however, U-Boot does use the EQOS one as primary MAC as well. This is just how U-Boot does things. There
> is no easy way to change the actual instance numbering. Actually just like on Linux really with the one
> difference that U-Boot will always show both independent whether or not your carrier board even has the second
> PHY or not. This is due to U-Boot doing lazy loading aka not touch any Ethernet hardware unless you actually
> run some network commands.
> 
> > The mismatch results in
> > the MAC addresses being swapped between eth0 and eth1 when comparing
> > U-Boot and Linux.
> 
> No, this alias should really be what ensures the correct MAC addresses.
> 
> > Am I using a too old boot loader, or should the two
> > ethernet controlls be swapped here ?
> 
> Yes, I guess you might not be using latest mainline U-Boot. I just verified this on my table again having both
> the Dahlia and Verdin Development carrier boards available. Please note that on the Verdin Development Board
> the primary Ethernet is also called eth1. Unfortunately, changing this naming is also not entirely trivial. But
> it really should have the proper MAC address.

I've updated U-Boot to 2022-rc4 and I confirm it now works fine.

> Dahlia
> 
> U-Boot 2022.04-rc4-00068-g5f68470d69 (Mar 23 2022 - 10:15:46 +0100)
> 
> Verdin iMX8MP # echo $ethaddr
> 00:14:2d:6c:71:64
> => verified with wireshark
> 
> root@verdin-imx8mp-07106916:~# ip addr
> ...
> 4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
>     link/ether 00:14:2d:6c:71:64 brd ff:ff:ff:ff:ff:ff
>     inet 192.168.10.239/24 brd 192.168.10.255 scope global eth0
>        valid_lft forever preferred_lft forever
>     inet6 fe80::214:2dff:fe6c:7164/64 scope link 
>        valid_lft forever preferred_lft forever
> ...
> 
> Verdin Developer Board
> 
> U-Boot 2022.04-rc4-00068-g5f68470d69 (Mar 23 2022 - 10:15:46 +0100)
> 
> Verdin iMX8MP # echo $ethaddr  
> 00:14:2d:6c:71:64
> => verified with wireshark
> 
> root@verdin-imx8mp-07106916:~# uname -a
> Linux verdin-imx8mp-07106916 5.17.0-rc8-next-20220317-00003-g695dc7d13c2a #12 SMP PREEMPT Thu Mar 17 16:07:49
> CET 2022 aarch64 aarch64 aarch64 GNU/Linux
> 
> root@verdin-imx8mp-07106916:~# ip addr
> ...
> 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,DYNAMIC,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
>     link/ether 00:14:2d:7c:71:64 brd ff:ff:ff:ff:ff:ff
> ...
> 5: eth1: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
>     link/ether 00:14:2d:6c:71:64 brd ff:ff:ff:ff:ff:ff
>     inet 192.168.10.239/24 brd 192.168.10.255 scope global eth1
>        valid_lft forever preferred_lft forever
>     inet6 fe80::214:2dff:fe6c:7164/64 scope link 
>        valid_lft forever preferred_lft forever
> ...
> 
> > > +               rtc0 = &rtc_i2c;
> > > +               rtc1 = &snvs_rtc;
> > > +       };
> > 
> > [snip]
> > 
> > With these issues addressed,
> > 
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Thanks again!
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 7f51b537df40..f1d7607888e2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -78,6 +78,10 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
new file mode 100644
index 000000000000..103d97a3b029
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
@@ -0,0 +1,125 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&backlight {
+	power-supply = <&reg_3p3v>;
+};
+
+/* Verdin SPI_1 */
+&ecspi1 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&eqos {
+	status = "okay";
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&flexcan2 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Verdin PCIE_1 */
+
+/* Verdin PWM_1 */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&pwm3 {
+	status = "okay";
+};
+
+&reg_usdhc2_vmmc {
+	vin-supply = <&reg_3p3v>;
+};
+
+/* VERDIN I2S_1 */
+
+/* Verdin UART_1 */
+&uart1 {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux Console */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usb3_1 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
new file mode 100644
index 000000000000..1dfa9012e70d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
@@ -0,0 +1,44 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	reg_eth2phy: regulator-eth2phy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio_expander_21 4 GPIO_ACTIVE_HIGH>; /* ETH_PWR_EN */
+		off-on-delay = <500000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_3p3v>;
+	};
+};
+
+&fec {
+	phy-supply = <&reg_eth2phy>;
+	status = "okay";
+};
+
+&gpio_expander_21 {
+	status = "okay";
+	vcc-supply = <&reg_1p8v>;
+};
+
+/* Verdin I2C_1 */
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&uart1 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+};
+
+/* Limit frequency on dev board due to long traces and bad signal integrity */
+&usdhc2 {
+	max-frequency = <100000000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
new file mode 100644
index 000000000000..68147b0c1b35
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
@@ -0,0 +1,18 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-nonwifi.dtsi"
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus on Dahlia Board";
+	compatible = "toradex,verdin-imx8mp-nonwifi-dahlia",
+		     "toradex,verdin-imx8mp-nonwifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..879ff687cf2b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
@@ -0,0 +1,18 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-nonwifi.dtsi"
+#include "imx8mp-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mp-nonwifi-dev",
+		     "toradex,verdin-imx8mp-nonwifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..91d597391b7c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
@@ -0,0 +1,54 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&gpio5 {
+	gpio-line-names = "SODIMM_42",
+			  "SODIMM_46",
+			  "SODIMM_187",
+			  "SODIMM_20",
+			  "SODIMM_22",
+			  "SODIMM_15",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "SODIMM_164",
+			  "SODIMM_152",
+			  "SODIMM_116",
+			  "SODIMM_128",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "SODIMM_129",
+			  "SODIMM_131",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_147",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
+		    <&pinctrl_hdmi_hog>;
+};
+
+/*
+ * Verdin UART_4
+ * Often used by the M7 and then should not be enabled here.
+ */
+&uart4 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
new file mode 100644
index 000000000000..804567f6ccee
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
@@ -0,0 +1,18 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-wifi.dtsi"
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus WB on Dahlia Board";
+	compatible = "toradex,verdin-imx8mp-wifi-dahlia",
+		     "toradex,verdin-imx8mp-wifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..c1713c28cdce
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
@@ -0,0 +1,18 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-wifi.dtsi"
+#include "imx8mp-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mp-wifi-dev",
+		     "toradex,verdin-imx8mp-wifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
new file mode 100644
index 000000000000..34d9bc48c899
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
@@ -0,0 +1,82 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_AW-CM276NF";
+		startup-delay-us = <2000>;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_42",
+			  "SODIMM_46",
+			  "SODIMM_187",
+			  "SODIMM_20",
+			  "SODIMM_22",
+			  "SODIMM_15",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "SODIMM_129",
+			  "SODIMM_131",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_147",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>, <&pinctrl_gpio_hog4>,
+		    <&pinctrl_hdmi_hog>;
+};
+
+/* On-module Bluetooth */
+&uart4 {
+	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_bt_uart>;
+	status = "okay";
+};
+
+/* On-module Wi-Fi */
+&usdhc1 {
+	bus-width = <4>;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wifi_ctrl>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_wifi_ctrl>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_wifi_ctrl>;
+	vmmc-supply = <&reg_wifi_en>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
new file mode 100644
index 000000000000..26d6c2819ee8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
@@ -0,0 +1,1373 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "dt-bindings/pwm/pwm.h"
+#include "imx8mp.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		/* Ethernet aliases to ensure correct MAC addresses */
+		ethernet0 = &eqos;
+		ethernet1 = &fec;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
+		power-supply = <&reg_3p3v>;
+		/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
+		pwms = <&pwm3 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	backlight_mezzanine: backlight-mezzanine {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin GPIO 4 (SODIMM 212) */
+		enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		/* Verdin PWM_2 (SODIMM 16) */
+		pwms = <&pwm2 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	/* Carrier Board Supplies */
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "+V1.8_SW";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "+V5_SW";
+	};
+
+	/* Non PMIC On-module Supplies */
+	reg_module_eth1phy: regulator-module-eth1phy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
+		off-on-delay = <500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "On-module +V3.3_ETH";
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_vdd_3v3>;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_1_EN";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb2_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_2_EN";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SD";
+		startup-delay-us = <2000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Use the kernel configuration settings instead */
+		/delete-node/ linux,cma;
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&eqos {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_module_eth1phy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	snps,force_thresh_dma_mode;
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			eee-broken-100tx;
+			eee-broken-1000t;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <5>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+			snps,map-to-dma-channel = <0>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+			snps,map-to-dma-channel = <1>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+			snps,map-to-dma-channel = <2>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+			snps,map-to-dma-channel = <3>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+			snps,map-to-dma-channel = <4>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <5>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+		};
+	};
+};
+
+/* Verdin ETH_2_RGMII */
+&fec {
+	fsl,magic-packet;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec>;
+	pinctrl-1 = <&pinctrl_fec_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio4>;
+			interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* Verdin CAN_1 */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+
+/* Verdin CAN_2 */
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "disabled";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_206",
+			  "SODIMM_208",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_210",
+			  "SODIMM_212",
+			  "SODIMM_216",
+			  "SODIMM_218",
+			  "",
+			  "",
+			  "SODIMM_16",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_185",
+			  "SODIMM_91";
+};
+
+&gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_143",
+			  "SODIMM_141",
+			  "",
+			  "",
+			  "SODIMM_161",
+			  "",
+			  "SODIMM_84",
+			  "SODIMM_78",
+			  "SODIMM_74",
+			  "SODIMM_80",
+			  "SODIMM_82",
+			  "SODIMM_70",
+			  "SODIMM_72";
+
+	ctrl-sleep-moci-hog {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <29 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_66",
+			  "",
+			  "SODIMM_64",
+			  "",
+			  "",
+			  "SODIMM_34",
+			  "SODIMM_19",
+			  "",
+			  "SODIMM_32",
+			  "",
+			  "",
+			  "SODIMM_30",
+			  "SODIMM_59",
+			  "SODIMM_57",
+			  "SODIMM_63",
+			  "SODIMM_61";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_252",
+			  "SODIMM_222",
+			  "SODIMM_36",
+			  "SODIMM_220",
+			  "SODIMM_193",
+			  "SODIMM_191",
+			  "SODIMM_201",
+			  "SODIMM_203",
+			  "SODIMM_205",
+			  "SODIMM_207",
+			  "SODIMM_199",
+			  "SODIMM_197",
+			  "SODIMM_221",
+			  "SODIMM_219",
+			  "SODIMM_217",
+			  "SODIMM_215",
+			  "SODIMM_211",
+			  "SODIMM_213",
+			  "SODIMM_189",
+			  "SODIMM_244",
+			  "SODIMM_38",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_135",
+			  "SODIMM_133",
+			  "SODIMM_17",
+			  "SODIMM_24",
+			  "SODIMM_26",
+			  "SODIMM_21",
+			  "SODIMM_256",
+			  "SODIMM_48",
+			  "SODIMM_44";
+};
+
+/* On-module I2C */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450c";
+		interrupt-parent = <&gpio1>;
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		/* The bootloader is expected to switch on LDO4 and the I2C level shifter. */
+
+		regulators {
+			BUCK1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "On-module +VDD_SOC (BUCK1)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1025000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "On-module +VDD_ARM (BUCK2)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "On-module +V3.3 (BUCK4)";
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "PWR_1V8_MOCI (BUCK5)";
+			};
+
+			BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1155000>;
+				regulator-min-microvolt = <1045000>;
+				regulator-name = "On-module +VDD_DDR (BUCK6)";
+			};
+
+			LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "On-module +V1.8_SNVS (LDO1)";
+			};
+
+			LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1150000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "On-module +V0.8_SNVS (LDO2)";
+			};
+
+			LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V1.8A (LDO3)";
+			};
+
+			LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "On-module +V3.3_ADC (LDO4)";
+			};
+
+			LDO5 {
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V3.3_1.8_SD (LDO5)";
+			};
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	/* On-module temperature sensor */
+	hwmon_temp_module: sensor@48 {
+		compatible = "ti,tmp1075";
+		reg = <0x48>;
+		vs-supply = <&reg_vdd_1v8>;
+	};
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Verdin I2C_1 (ADC_4 - ADC_3) */
+		channel@0 {
+			reg = <0>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_4 - ADC_1) */
+		channel@1 {
+			reg = <1>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_3 - ADC_1) */
+		channel@2 {
+			reg = <2>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_2 - ADC_1) */
+		channel@3 {
+			reg = <3>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_4 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_3 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_1 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+	};
+
+	eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	clock-frequency = <10000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+
+	atmel_mxt_ts_mezzanine: touch-mezzanine@4a {
+		compatible = "atmel,maxtouch";
+		/* Verdin GPIO_3 (SODIMM 210) */
+		interrupt-parent = <&gpio1>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x4a>;
+		/* Verdin GPIO_2 (SODIMM 208) */
+		reset-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+/* Verdin I2C_3_HDMI */
+
+/* Verdin I2C_4_CSI */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6416";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x21>;
+		vcc-supply = <&reg_3p3v>;
+		status = "disabled";
+	};
+
+	lvds_ti_sn65dsi83: bridge@2c {
+		compatible = "ti,sn65dsi83";
+		/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		reg = <0x2c>;
+		status = "disabled";
+	};
+
+	/* Current measurement into module VCC */
+	hwmon: hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+		status = "disabled";
+	};
+
+	hdmi_lontium_lt8912: hdmi@48 {
+		compatible = "lontium,lt8912b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		reg = <0x48>;
+		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		/*
+		 * Verdin GPIO_9_DSI
+		 * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI83 IRQ albeit currently unused)
+		 */
+		interrupt-parent = <&gpio4>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
+		reg = <0x4a>;
+		/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	/* Temperature sensor on carrier board */
+	hwmon_temp: sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+		status = "disabled";
+	};
+
+	/* EEPROM on display adapter (MIPI DSI Display Adapter) */
+	eeprom_display_adapter: eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+		status = "disabled";
+	};
+
+	/* EEPROM on carrier board */
+	eeprom_carrier_board: eeprom@57 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x57>;
+		status = "disabled";
+	};
+};
+
+/* Verdin PCIE_1 */
+
+/* Verdin PWM_1 */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_1>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_2 */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_2>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_3_DSI */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_3>;
+	#pwm-cells = <3>;
+};
+
+/* VERDIN I2S_1 */
+
+/* VERDIN I2S_2 */
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Verdin UART_1 */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	fsl,uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,uart-has-rtscts;
+};
+
+/* Verdin UART_3, used as the Linux Console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+};
+
+/* Verdin UART_4, used for Bluetooth on Wi-Fi/Bluetooth SKUs */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+/* Verdin USB_1 */
+&usb3_phy0 {
+	vbus-supply = <&reg_usb1_vbus>;
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	maximum-speed = "high-speed";
+	over-current-active-low;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_1_id>;
+	srp-disable;
+};
+
+/* Verdin USB_2 */
+&usb3_phy1 {
+	vbus-supply = <&reg_usb2_vbus>;
+};
+
+&usb_dwc3_1 {
+	disable-over-current;
+	dr_mode = "host";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+};
+
+/* On-module eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	status = "okay";
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_bt_uart: btuartgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI2_MISO__UART4_DCE_CTS	0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_MOSI__UART4_DCE_TX		0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_SCLK__UART4_DCE_RX		0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_SS0__UART4_DCE_RTS		0x1c4>;
+	};
+
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29		0x1c4>;	/* SODIMM 256 */
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO		0x1c4>,	/* SODIMM 198 */
+			<MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI		0x4>,	/* SODIMM 200 */
+			<MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK		0x4>,	/* SODIMM 196 */
+			<MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09		0x1c4>;	/* SODIMM 202 */
+	};
+
+	/* Connection On Board PHY */
+	pinctrl_eqos: eqosgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3>,
+			<MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3>,
+			<MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91>,
+			<MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91>,
+			<MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91>,
+			<MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91>,
+			<MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91>,
+			<MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x91>,
+			<MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f>,
+			<MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x1f>,
+			<MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f>;
+	};
+
+	/* ETH_INT# shared with TPM_INT# (usually N/A) */
+	pinctrl_eth_tpm_int: ethtpmintgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10		0x1c4>;
+	};
+
+	/* Connection Carrier Board PHY ETH_2 */
+	pinctrl_fec: fecgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3>,	/* SODIMM 193 */
+			<MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3>,	/* SODIMM 191 */
+			<MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x91>,	/* SODIMM 201 */
+			<MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x91>,	/* SODIMM 203 */
+			<MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x91>,	/* SODIMM 205 */
+			<MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x91>,	/* SODIMM 207 */
+			<MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91>,	/* SODIMM 197 */
+			<MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91>,	/* SODIMM 199 */
+			<MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0	0x1f>,	/* SODIMM 221 */
+			<MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1	0x1f>,	/* SODIMM 219 */
+			<MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2	0x1f>,	/* SODIMM 217 */
+			<MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3	0x1f>,	/* SODIMM 215 */
+			<MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f>,	/* SODIMM 211 */
+			<MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC	0x1f>,	/* SODIMM 213 */
+			<MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18		0x1c4>;	/* SODIMM 189 */
+	};
+
+	pinctrl_fec_sleep: fecsleepgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3>,	/* SODIMM 193 */
+			<MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3>,	/* SODIMM 191 */
+			<MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x91>,	/* SODIMM 201 */
+			<MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x91>,	/* SODIMM 203 */
+			<MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x91>,	/* SODIMM 205 */
+			<MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x91>,	/* SODIMM 207 */
+			<MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91>,	/* SODIMM 197 */
+			<MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91>,	/* SODIMM 199 */
+			<MX8MP_IOMUXC_SAI1_TXD0__GPIO4_IO12		0x1f>,	/* SODIMM 221 */
+			<MX8MP_IOMUXC_SAI1_TXD1__GPIO4_IO13		0x1f>,	/* SODIMM 219 */
+			<MX8MP_IOMUXC_SAI1_TXD2__GPIO4_IO14		0x1f>,	/* SODIMM 217 */
+			<MX8MP_IOMUXC_SAI1_TXD3__GPIO4_IO15		0x1f>,	/* SODIMM 215 */
+			<MX8MP_IOMUXC_SAI1_TXD4__GPIO4_IO16		0x1f>,	/* SODIMM 211 */
+			<MX8MP_IOMUXC_SAI1_TXD5__GPIO4_IO17		0x1f>,	/* SODIMM 213 */
+			<MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18		0x184>;	/* SODIMM 189 */
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_RX__CAN1_RX			0x154>,	/* SODIMM 22 */
+			<MX8MP_IOMUXC_SPDIF_TX__CAN1_TX			0x154>;	/* SODIMM 20 */
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX		0x154>,	/* SODIMM 26 */
+			<MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX		0x154>;	/* SODIMM 24 */
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK		0x1c2>,	/* SODIMM 52 */
+			<MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B	0x82>,	/* SODIMM 54 */
+			<MX8MP_IOMUXC_NAND_DQS__FLEXSPI_A_DQS		0x82>,	/* SODIMM 66 */
+			<MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00	0x82>,	/* SODIMM 56 */
+			<MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01	0x82>,	/* SODIMM 58 */
+			<MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02	0x82>,	/* SODIMM 60 */
+			<MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03	0x82>,	/* SODIMM 62 */
+			<MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16		0x82>;	/* SODIMM 64 */
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x184>;	/* SODIMM 206 */
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x1c4>;	/* SODIMM 208 */
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05		0x184>;	/* SODIMM 210 */
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x184>;	/* SODIMM 212 */
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x184>;	/* SODIMM 216 */
+	};
+
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x184>;	/* SODIMM 218 */
+	};
+
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03		0x184>;	/* SODIMM 220 */
+	};
+
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01		0x184>;	/* SODIMM 222 */
+	};
+
+	/* Verdin GPIO_9_DSI (pulled-up as active-low) */
+	pinctrl_gpio_9_dsi: gpio9dsigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25		0x1c4>;	/* SODIMM 17 */
+	};
+
+	/* Verdin GPIO_10_DSI */
+	pinctrl_gpio_10_dsi: gpio10dsigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28		0x1c4>;	/* SODIMM 21 */
+	};
+
+	/* Non-wifi MSP usage only */
+	pinctrl_gpio_hog1: gpiohog1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI2_MISO__GPIO5_IO12		0x1c4>,	/* SODIMM 116 */
+			<MX8MP_IOMUXC_ECSPI2_MOSI__GPIO5_IO11		0x1c4>,	/* SODIMM 152 */
+			<MX8MP_IOMUXC_ECSPI2_SCLK__GPIO5_IO10		0x1c4>,	/* SODIMM 164 */
+			<MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x1c4>;	/* SODIMM 128 */
+	};
+
+	/* USB_2_OC# */
+	pinctrl_gpio_hog2: gpiohog2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02		0x1c4>;	/* SODIMM 187 */
+	};
+
+	pinctrl_gpio_hog3: gpiohog3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13		0x1c4>,	/* SODIMM 157 */
+			/* CSI_1_MCLK */
+			<MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x1c4>;	/* SODIMM 91 */
+	};
+
+	/* Wifi usage only */
+	pinctrl_gpio_hog4: gpiohog4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART4_RXD__GPIO5_IO28		0x1c4>,	/* SODIMM 151 */
+			<MX8MP_IOMUXC_UART4_TXD__GPIO5_IO29		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00		0x1c4>;	/* SODIMM 252 */
+	};
+
+	pinctrl_hdmi_hog: hdmihoggrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC	0x40000019>,	/* SODIMM 63 */
+			<MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL	0x400001c3>,	/* SODIMM 59 */
+			<MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA	0x400001c3>,	/* SODIMM 57 */
+			<MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD	0x40000019>;	/* SODIMM 61 */
+	};
+
+	/* On-module I2C */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c6>,	/* SODIMM 55 */
+			<MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16		0x400001c6>,	/* SODIMM 55 */
+			<MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c6>,	/* SODIMM 95 */
+			<MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18		0x400001c6>,	/* SODIMM 95 */
+			<MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001c6>,	/* SODIMM 14 */
+			<MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20		0x400001c6>,	/* SODIMM 14 */
+			<MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
+	pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00		0x184>;	/* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_OUT shared with SAI3 */
+	pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01		0x184>;	/* SODIMM 46 */
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19		0x4>,	/* SODIMM 244 */
+			<MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x1c4>;	/* PMIC_EN_PCIe_CLK, unused */
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x1c4>;	/* PMIC_INT# */
+	};
+
+	pinctrl_pwm_1: pwm1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT		0x6>;	/* SODIMM 15 */
+	};
+
+	pinctrl_pwm_2: pwm2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO11__PWM2_OUT		0x6>;	/* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI shared with GPIO3_IO20 */
+	pinctrl_pwm_3: pwm3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXC__PWM3_OUT		0x6>;	/* SODIMM 19 */
+	};
+
+	/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM3_OUT */
+	pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsi1hpdgpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x184>;	/* SODIMM 19 */
+	};
+
+	pinctrl_reg_eth: regethgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_WP__GPIO2_IO20		0x184>;	/* PMIC_EN_ETH */
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_MCLK__AUDIOMIX_SAI1_MCLK		0x96>,	/* SODIMM 38 */
+			<MX8MP_IOMUXC_SAI1_RXD0__AUDIOMIX_SAI1_RX_DATA00	0x1d6>,	/* SODIMM 36 */
+			<MX8MP_IOMUXC_SAI5_MCLK__AUDIOMIX_SAI1_TX_BCLK		0x1d6>,	/* SODIMM 30 */
+			<MX8MP_IOMUXC_SAI5_RXD1__AUDIOMIX_SAI1_TX_SYNC		0x1d6>,	/* SODIMM 32 */
+			<MX8MP_IOMUXC_SAI5_RXFS__AUDIOMIX_SAI1_TX_DATA00	0x96>;	/* SODIMM 34 */
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXD__AUDIOMIX_SAI3_RX_DATA00	0x1d6>,	/* SODIMM 48 */
+			<MX8MP_IOMUXC_SAI3_TXC__AUDIOMIX_SAI3_TX_BCLK	0x1d6>,	/* SODIMM 42 */
+			<MX8MP_IOMUXC_SAI3_TXD__AUDIOMIX_SAI3_TX_DATA00	0x96>,	/* SODIMM 46 */
+			<MX8MP_IOMUXC_SAI3_TXFS__AUDIOMIX_SAI3_TX_SYNC	0x1d6>;	/* SODIMM 44 */
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS		0x1c4>,	/* SODIMM 135 */
+			<MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS		0x1c4>,	/* SODIMM 133 */
+			<MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX		0x1c4>,	/* SODIMM 129 */
+			<MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX		0x1c4>;	/* SODIMM 131 */
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA4__UART2_DCE_RTS		0x1c4>,	/* SODIMM 143 */
+			<MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS		0x1c4>,	/* SODIMM 141 */
+			<MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x1c4>,	/* SODIMM 137 */
+			<MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x1c4>; /* SODIMM 139 */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX		0x1c4>,	/* SODIMM 147 */
+			<MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX		0x1c4>;	/* SODIMM 149 */
+	};
+
+	/* Non-wifi usage only */
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX		0x1c4>,	/* SODIMM 151 */
+			<MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_usb1_vbus: usb1vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO12__USB1_OTG_PWR		0x19>;	/* SODIMM 155 */
+	};
+
+	/* USB_1_ID */
+	pinctrl_usb_1_id: usb1idgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10		0x1c4>;	/* SODIMM 161 */
+	};
+
+	pinctrl_usb2_vbus: usb2vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR		0x19>;	/* SODIMM 185 */
+	};
+
+	/* On-module Wi-Fi */
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x190>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d0>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x194>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x196>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d6>;
+	};
+
+	pinctrl_usdhc2_cd: usdhc2cdgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x1c4>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x0>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22		0x4>;	/* SODIMM 76 */
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,	/* PMIC_USDHC_VSELECT */
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190>,	/* SODIMM 78 */
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0>,	/* SODIMM 74 */
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0>,	/* SODIMM 80 */
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0>,	/* SODIMM 82 */
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0>,	/* SODIMM 70 */
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0>;	/* SODIMM 72 */
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-slpgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x100>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x100>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x100>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x190>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x194>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x196>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d2>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d2>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d2>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d2>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6>;	/* PMIC_WDI */
+	};
+
+	pinctrl_bluetooth_ctrl: bluetoothctrlgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08		0x1c4>;	/* WIFI_WKUP_BT */
+	};
+
+	pinctrl_wifi_ctrl: wifictrlgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09		0x1c4>;	/* WIFI_WKUP_WLAN */
+	};
+
+	pinctrl_wifi_i2s: wifii2sgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21		0x1d6>,	/* WIFI_TX_SYNC */
+			<MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21		0x96>,	/* WIFI_RX_DATA0 */
+			<MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23		0x1d6>,	/* WIFI_TX_BCLK */
+			<MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24		0x1d6>;	/* WIFI_TX_DATA0 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11		0x184>;	/* PMIC_EN_WIFI */
+	};
+};