| Message ID | 20220331171827.12483-1-wens@kernel.org (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | net: stmmac: Fix unset max_speed difference between DT and non-DT platforms | expand |
On Fri, 1 Apr 2022 01:18:27 +0800 Chen-Yu Tsai wrote: > From: Chen-Yu Tsai <wens@csie.org> > > In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree > property"), when DT platforms don't set "max-speed", max_speed is set to > -1; for non-DT platforms, it stays the default 0. > > Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"), > the check for a valid max_speed setting was to check if it was greater > than zero. This commit got it right, but subsequent patches just checked > for non-zero, which is incorrect for DT platforms. > > In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()") > the conversion switched completely to checking for non-zero value as a > valid value, which caused 1000base-T to stop getting advertised by > default. > > Instead of trying to fix all the checks, simply leave max_speed alone if > DT property parsing fails. > > Fixes: 9cbadf094d9d ("net: stmmac: support max-speed device tree property") > Fixes: 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()") > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > --- You should always CC authors of patches you put on CC as they have the most context to review, usually. Please use get_maintainers.pl and repost. > This was first noticed on ROC-RK3399-PC, and also observed on ROC-RK3328-CC. > The fix was tested on ROC-RK3328-CC and Libre Computer ALL-H5-ALL-CC. > > drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 +-- > 1 file changed, 1 insertion(+), 2 deletions(-) > > diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c > index 5d29f336315b..11e1055e8260 100644 > --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c > +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c > @@ -431,8 +431,7 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) > plat->phylink_node = np; > > /* Get max speed of operation from device tree */ > - if (of_property_read_u32(np, "max-speed", &plat->max_speed)) > - plat->max_speed = -1; > + of_property_read_u32(np, "max-speed", &plat->max_speed); > > plat->bus_id = of_alias_get_id(np, "ethernet"); > if (plat->bus_id < 0)
On Fri, Apr 01, 2022 at 01:18:27AM +0800, Chen-Yu Tsai wrote: > From: Chen-Yu Tsai <wens@csie.org> > > In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree > property"), when DT platforms don't set "max-speed", max_speed is set to > -1; for non-DT platforms, it stays the default 0. > > Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"), > the check for a valid max_speed setting was to check if it was greater > than zero. This commit got it right, but subsequent patches just checked > for non-zero, which is incorrect for DT platforms. Sounds like it's got to complicated... > In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()") > the conversion switched completely to checking for non-zero value as a > valid value, which caused 1000base-T to stop getting advertised by > default. > > Instead of trying to fix all the checks, simply leave max_speed alone if > DT property parsing fails. And this kind of proves that point - if deleting code fixes it... Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c index 5d29f336315b..11e1055e8260 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c @@ -431,8 +431,7 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) plat->phylink_node = np; /* Get max speed of operation from device tree */ - if (of_property_read_u32(np, "max-speed", &plat->max_speed)) - plat->max_speed = -1; + of_property_read_u32(np, "max-speed", &plat->max_speed); plat->bus_id = of_alias_get_id(np, "ethernet"); if (plat->bus_id < 0)