| Message ID | 20220419133723.1394715-27-arnd@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | OMAP1 full multiplatform conversion | expand |
Hi, On Tue, Apr 19, 2022 at 03:37:08PM +0200, Arnd Bergmann wrote: > From: Arnd Bergmann <arnd@arndb.de> > > The address range 0xfee00000-0xfeffffff is used for PCI and > PCMCIA I/O port mappings, but OMAP1 has its static mappings > there as well. > > Move the OMAP1 addresses a little higher to avoid crashing > at boot. This has the same problem I reported in 2019, with earlyprintk the system no longer boots: https://marc.info/?t=156530014200005&r=1&w=2 Tested on OSK and SX1/qemu. A. > Signed-off-by: Arnd Bergmann <arnd@arndb.de> > --- > arch/arm/Kconfig.debug | 6 +++--- > arch/arm/mach-omap1/include/mach/hardware.h | 2 +- > 2 files changed, 4 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug > index 0c9497d549e3..f57b449000f7 100644 > --- a/arch/arm/Kconfig.debug > +++ b/arch/arm/Kconfig.debug > @@ -1837,9 +1837,9 @@ config DEBUG_UART_VIRT > default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN > default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN > default 0xfef36000 if DEBUG_HIGHBANK_UART > - default 0xfefb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 > - default 0xfefb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 > - default 0xfefb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 > + default 0xff000000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 > + default 0xff000800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 > + default 0xff009800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 > default 0xffd01000 if DEBUG_HIP01_UART > default DEBUG_UART_PHYS if !MMU > depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \ > diff --git a/arch/arm/mach-omap1/include/mach/hardware.h b/arch/arm/mach-omap1/include/mach/hardware.h > index 05c5cd3e95f4..e3522e601ccd 100644 > --- a/arch/arm/mach-omap1/include/mach/hardware.h > +++ b/arch/arm/mach-omap1/include/mach/hardware.h > @@ -63,7 +63,7 @@ static inline u32 omap_cs3_phys(void) > > #endif /* ifndef __ASSEMBLER__ */ > > -#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */ > +#define OMAP1_IO_OFFSET 0x00fb0000 /* Virtual IO = 0xff000000 */ > #define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET) > > #include <mach/serial.h> > -- > 2.29.2 >
On Wed, Apr 20, 2022 at 3:46 PM Aaro Koskinen <aaro.koskinen@iki.fi> wrote: > > Hi, > > On Tue, Apr 19, 2022 at 03:37:08PM +0200, Arnd Bergmann wrote: > > From: Arnd Bergmann <arnd@arndb.de> > > > > The address range 0xfee00000-0xfeffffff is used for PCI and > > PCMCIA I/O port mappings, but OMAP1 has its static mappings > > there as well. > > > > Move the OMAP1 addresses a little higher to avoid crashing > > at boot. > > This has the same problem I reported in 2019, with earlyprintk the > system no longer boots: > > https://marc.info/?t=156530014200005&r=1&w=2 > > Tested on OSK and SX1/qemu. Thanks a lot for testing! I managed to get to the bottom of this after just a few hours, and it turned out to be a simple math error on my end, as I got the alignment wrong, the offset has to be 0x00f00000 instead of 0x00fb0000 be section aligned. I made sure the kernel boots up (to the point of missing a rootfs) and uploaded the fixed branch. Arnd
* Arnd Bergmann <arnd@kernel.org> [220420 19:18]: > On Wed, Apr 20, 2022 at 3:46 PM Aaro Koskinen <aaro.koskinen@iki.fi> wrote: > > > > Hi, > > > > On Tue, Apr 19, 2022 at 03:37:08PM +0200, Arnd Bergmann wrote: > > > From: Arnd Bergmann <arnd@arndb.de> > > > > > > The address range 0xfee00000-0xfeffffff is used for PCI and > > > PCMCIA I/O port mappings, but OMAP1 has its static mappings > > > there as well. > > > > > > Move the OMAP1 addresses a little higher to avoid crashing > > > at boot. > > > > This has the same problem I reported in 2019, with earlyprintk the > > system no longer boots: > > > > https://marc.info/?t=156530014200005&r=1&w=2 > > > > Tested on OSK and SX1/qemu. > > Thanks a lot for testing! > > I managed to get to the bottom of this after just a few hours, and > it turned out to be a simple math error on my end, as I got > the alignment wrong, the offset has to be 0x00f00000 > instead of 0x00fb0000 be section aligned. I made sure the > kernel boots up (to the point of missing a rootfs) and uploaded > the fixed branch. Good to hear this got sorted out :) Regards, Tony
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 0c9497d549e3..f57b449000f7 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -1837,9 +1837,9 @@ config DEBUG_UART_VIRT default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN default 0xfef36000 if DEBUG_HIGHBANK_UART - default 0xfefb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 - default 0xfefb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 - default 0xfefb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 + default 0xff000000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1 + default 0xff000800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2 + default 0xff009800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3 default 0xffd01000 if DEBUG_HIP01_UART default DEBUG_UART_PHYS if !MMU depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \ diff --git a/arch/arm/mach-omap1/include/mach/hardware.h b/arch/arm/mach-omap1/include/mach/hardware.h index 05c5cd3e95f4..e3522e601ccd 100644 --- a/arch/arm/mach-omap1/include/mach/hardware.h +++ b/arch/arm/mach-omap1/include/mach/hardware.h @@ -63,7 +63,7 @@ static inline u32 omap_cs3_phys(void) #endif /* ifndef __ASSEMBLER__ */ -#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */ +#define OMAP1_IO_OFFSET 0x00fb0000 /* Virtual IO = 0xff000000 */ #define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET) #include <mach/serial.h>