diff mbox series

[v11,6/6] arm64: dts: allwinner: h616: Add X96 Mate TV box support

Message ID 20220428230933.15262-7-andre.przywara@arm.com (mailing list archive)
State New, archived
Headers show
Series arm64: sunxi: Initial Allwinner H616 SoC support | expand

Commit Message

Andre Przywara April 28, 2022, 11:09 p.m. UTC 
The X96 Mate is an Allwinner H616 based TV box, featuring:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 2GiB/4GiB RAM (fully usable!)
  - 16/32/64GiB eMMC
  - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
  - Unsupported Allwinner WiFi chip
  - 2 x USB 2.0 host ports
  - HDMI port
  - IR receiver
  - 5V/2A DC power supply via barrel plug

For more information see: https://linux-sunxi.org/X96_Mate

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h616-x96-mate.dts    | 177 ++++++++++++++++++
 2 files changed, 178 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts

Comments

Jernej Škrabec May 3, 2022, 7:44 p.m. UTC | #1 
Similar comments as for OrangePi Zero2...

Dne petek, 29. april 2022 ob 01:09:33 CEST je Andre Przywara napisal(a):
> The X96 Mate is an Allwinner H616 based TV box, featuring:
>   - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
>   - 2GiB/4GiB RAM (fully usable!)
>   - 16/32/64GiB eMMC
>   - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
>   - Unsupported Allwinner WiFi chip
>   - 2 x USB 2.0 host ports
>   - HDMI port
>   - IR receiver
>   - 5V/2A DC power supply via barrel plug
> 
> For more information see: https://linux-sunxi.org/X96_Mate

Please remove external links.

> 
> Add a basic devicetree for it, with SD card and eMMC working, as
> well as serial and the essential peripherals, like the AXP PMIC.
> 
> This DT is somewhat minimal, and should work on many other similar TV
> boxes with the Allwinner H616 chip.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../dts/allwinner/sun50i-h616-x96-mate.dts    | 177 ++++++++++++++++++
>  2 files changed, 178 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/
allwinner/Makefile
> index df2214e6d946..6a96494a2e0a 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -39,3 +39,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/
arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
> new file mode 100644
> index 000000000000..aedb3a3dff38
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
> @@ -0,0 +1,177 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2021 Arm Ltd.

2022?

> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +	model = "X96 Mate";
> +	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	reg_vcc5v: vcc5v {
> +		/* board wide 5V supply directly from the DC input */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +};
> +
> +&ir {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_dcdce>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&mmc2 {
> +	vmmc-supply = <&reg_dcdce>;
> +	vqmmc-supply = <&reg_bldo1>;
> +	bus-width = <8>;
> +	non-removable;
> +	cap-mmc-hw-reset;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +	status = "okay";
> +};
> +
> +&r_rsb {
> +	status = "okay";
> +
> +	axp305: pmic@745 {
> +		compatible = "x-powers,axp305", "x-powers,axp805",
> +			     "x-powers,axp806";
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		reg = <0x745>;
> +
> +		x-powers,self-working-mode;
> +		vina-supply = <&reg_vcc5v>;
> +		vinb-supply = <&reg_vcc5v>;
> +		vinc-supply = <&reg_vcc5v>;
> +		vind-supply = <&reg_vcc5v>;
> +		vine-supply = <&reg_vcc5v>;
> +		aldoin-supply = <&reg_vcc5v>;
> +		bldoin-supply = <&reg_vcc5v>;
> +		cldoin-supply = <&reg_vcc5v>;
> +
> +		regulators {
> +			reg_aldo1: aldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = 
<3300000>;
> +				regulator-max-microvolt = 
<3300000>;
> +				regulator-name = "vcc-sys";
> +			};
> +
> +			/* Enabled by the Android BSP */
> +			reg_aldo2: aldo2 {
> +				regulator-min-microvolt = 
<3300000>;
> +				regulator-max-microvolt = 
<3300000>;
> +				regulator-name = "vcc3v3-ext";
> +				status = "disabled";
> +			};
> +
> +			/* Enabled by the Android BSP */
> +			reg_aldo3: aldo3 {
> +				regulator-min-microvolt = 
<3300000>;
> +				regulator-max-microvolt = 
<3300000>;
> +				regulator-name = "vcc3v3-ext2";
> +				status = "disabled";
> +			};
> +
> +			reg_bldo1: bldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = 
<1800000>;
> +				regulator-max-microvolt = 
<1800000>;
> +				regulator-name = "vcc1v8";
> +			};
> +
> +			/* Enabled by the Android BSP */
> +			reg_bldo2: bldo2 {
> +				regulator-min-microvolt = 
<1800000>;
> +				regulator-max-microvolt = 
<1800000>;
> +				regulator-name = "vcc1v8-2";
> +				status = "disabled";
> +			};
> +
> +			bldo3 {
> +				/* unused */
> +			};
> +
> +			bldo4 {
> +				/* unused */
> +			};
> +
> +			cldo1 {
> +				regulator-min-microvolt = 
<2500000>;
> +				regulator-max-microvolt = 
<2500000>;
> +				regulator-name = "vcc2v5";
> +			};
> +
> +			cldo2 {
> +				/* unused */
> +			};
> +
> +			cldo3 {
> +				/* unused */
> +			};
> +
> +			reg_dcdca: dcdca {
> +				regulator-always-on;
> +				regulator-min-microvolt = 
<810000>;
> +				regulator-max-microvolt = 
<1080000>;
> +				regulator-name = "vdd-cpu";
> +			};
> +
> +			reg_dcdcc: dcdcc {
> +				regulator-always-on;
> +				regulator-min-microvolt = 
<810000>;
> +				regulator-max-microvolt = 
<1080000>;
> +				regulator-name = "vdd-gpu-sys";
> +			};
> +
> +			reg_dcdcd: dcdcd {
> +				regulator-always-on;
> +				regulator-min-microvolt = 
<1360000>;
> +				regulator-max-microvolt = 
<1360000>;
> +				regulator-name = "vdd-dram";
> +			};
> +
> +			reg_dcdce: dcdce {
> +				regulator-boot-on;

Did you check if reboot (when booted from SD card) works? It should have same 
issue as OrangePi Zero2.

Please also check and add pio power supplies.

Best regards,
Jernej

> +				regulator-min-microvolt = 
<3300000>;
> +				regulator-max-microvolt = 
<3300000>;
> +				regulator-name = "vcc-eth-mmc";
> +			};
> +
> +			sw {
> +				/* unused */
> +			};
> +		};
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_ph_pins>;
> +	status = "okay";
> +};
> -- 
> 2.35.3
> 
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index df2214e6d946..6a96494a2e0a 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -39,3 +39,4 @@  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 000000000000..aedb3a3dff38
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,177 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "X96 Mate";
+	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdce>;
+	vqmmc-supply = <&reg_bldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+				status = "disabled";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo3: aldo3 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+				status = "disabled";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8-2";
+				status = "disabled";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc2v5";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};