@@ -20,6 +20,7 @@
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
+#include <linux/pci.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/regmap.h>
@@ -134,6 +135,7 @@
#define MTK_IOMMU_TYPE_MASK (0x3 << 13)
/* PM and clock always on. e.g. infra iommu */
#define PM_CLK_AO BIT(15)
+#define IFA_IOMMU_PCIE_SUPPORT BIT(16)
#define MTK_IOMMU_HAS_FLAG_MASK(pdata, _x, mask) \
((((pdata)->flags) & (mask)) == (_x))
@@ -420,8 +422,11 @@ static int mtk_iommu_config(struct mtk_iommu_data *data, struct device *dev,
larb_mmu->mmu &= ~MTK_SMI_MMU_EN(portid);
} else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA)) {
peri_mmuen_msk = BIT(portid);
- peri_mmuen = enable ? peri_mmuen_msk : 0;
+ /* PCI dev has only one output id, enable the next writing bit for PCIe */
+ if (dev_is_pci(dev))
+ peri_mmuen_msk |= BIT(portid + 1);
+ peri_mmuen = enable ? peri_mmuen_msk : 0;
ret = regmap_update_bits(data->pericfg, PERICFG_IOMMU_1,
peri_mmuen_msk, peri_mmuen);
if (ret)
@@ -1054,6 +1059,15 @@ static int mtk_iommu_probe(struct platform_device *pdev)
ret = component_master_add_with_match(dev, &mtk_iommu_com_ops, match);
if (ret)
goto out_bus_set_null;
+ } else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA) &&
+ MTK_IOMMU_HAS_FLAG(data->plat_data, IFA_IOMMU_PCIE_SUPPORT)) {
+#ifdef CONFIG_PCI
+ if (!iommu_present(&pci_bus_type)) {
+ ret = bus_set_iommu(&pci_bus_type, &mtk_iommu_ops);
+ if (ret) /* PCIe fail don't affect platform_bus. */
+ goto out_list_del;
+ }
+#endif
}
return ret;
@@ -1084,6 +1098,11 @@ static int mtk_iommu_remove(struct platform_device *pdev)
if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_MM)) {
device_link_remove(data->smicomm_dev, &pdev->dev);
component_master_del(&pdev->dev, &mtk_iommu_com_ops);
+ } else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA) &&
+ MTK_IOMMU_HAS_FLAG(data->plat_data, IFA_IOMMU_PCIE_SUPPORT)) {
+#ifdef CONFIG_PCI
+ bus_set_iommu(&pci_bus_type, NULL);
+#endif
}
pm_runtime_disable(&pdev->dev);
devm_free_irq(&pdev->dev, data->irq, data);
Currently the code for of_iommu_configure_dev_id is like this: static int of_iommu_configure_dev_id(struct device_node *master_np, struct device *dev, const u32 *id) { struct of_phandle_args iommu_spec = { .args_count = 1 }; err = of_map_id(master_np, *id, "iommu-map", "iommu-map-mask", &iommu_spec.np, iommu_spec.args); ... } It supports only one id output. BUT our PCIe HW has two ID(one is for writing, the other is for reading). I'm not sure if we should change of_map_id to support output MAX_PHANDLE_ARGS. Here add the solution in ourselve drivers. If it's pcie case, enable one more bit. Not all infra iommu support PCIe, thus add a PCIe support flag here. Signed-off-by: Yong Wu <yong.wu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- drivers/iommu/mtk_iommu.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-)