diff mbox series

[v1,24/24] ARM: dts: imx7-colibri: add support for Toradex Iris carrier boards

Message ID 20220506155821.297686-1-marcel@ziswiler.com (mailing list archive)
State New, archived
Headers show
Series ARM: dts: imx7-colibri: device tree improvements | expand

Commit Message

Marcel Ziswiler May 6, 2022, 3:58 p.m. UTC
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm
Computer Module family Carrier Board.

Additional details available at
https://www.toradex.com/products/carrier-board/iris-carrier-board

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

 arch/arm/boot/dts/Makefile                    |   6 +
 arch/arm/boot/dts/imx6dl-colibri-iris.dts     |   9 +-
 arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi   | 112 ++++++++++++++++++
 arch/arm/boot/dts/imx7-colibri-iris.dtsi      | 108 +++++++++++++++++
 .../boot/dts/imx7d-colibri-emmc-iris-v2.dts   |  21 ++++
 arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts |  21 ++++
 arch/arm/boot/dts/imx7d-colibri-iris-v2.dts   |  83 +++++++++++++
 arch/arm/boot/dts/imx7d-colibri-iris.dts      |  56 +++++++++
 arch/arm/boot/dts/imx7s-colibri-iris-v2.dts   |  78 ++++++++++++
 arch/arm/boot/dts/imx7s-colibri-iris.dts      |  51 ++++++++
 10 files changed, 540 insertions(+), 5 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
 create mode 100644 arch/arm/boot/dts/imx7-colibri-iris.dtsi
 create mode 100644 arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
 create mode 100644 arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
 create mode 100644 arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
 create mode 100644 arch/arm/boot/dts/imx7d-colibri-iris.dts
 create mode 100644 arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
 create mode 100644 arch/arm/boot/dts/imx7s-colibri-iris.dts

Comments

Marcel Ziswiler May 6, 2022, 9:32 p.m. UTC | #1
On Fri, 2022-05-06 at 17:58 +0200, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Add support for Toradex Iris, small form-factor Pico-ITX Colibri Arm
> Computer Module family Carrier Board.
> 
> Additional details available at
> https://www.toradex.com/products/carrier-board/iris-carrier-board
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
>  arch/arm/boot/dts/Makefile                    |   6 +
>  arch/arm/boot/dts/imx6dl-colibri-iris.dts     |   9 +-
>  arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi   | 112 ++++++++++++++++++
>  arch/arm/boot/dts/imx7-colibri-iris.dtsi      | 108 +++++++++++++++++
>  .../boot/dts/imx7d-colibri-emmc-iris-v2.dts   |  21 ++++
>  arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts |  21 ++++
>  arch/arm/boot/dts/imx7d-colibri-iris-v2.dts   |  83 +++++++++++++
>  arch/arm/boot/dts/imx7d-colibri-iris.dts      |  56 +++++++++
>  arch/arm/boot/dts/imx7s-colibri-iris-v2.dts   |  78 ++++++++++++
>  arch/arm/boot/dts/imx7s-colibri-iris.dts      |  51 ++++++++
>  10 files changed, 540 insertions(+), 5 deletions(-)
>  create mode 100644 arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
>  create mode 100644 arch/arm/boot/dts/imx7-colibri-iris.dtsi
>  create mode 100644 arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
>  create mode 100644 arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
>  create mode 100644 arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
>  create mode 100644 arch/arm/boot/dts/imx7d-colibri-iris.dts
>  create mode 100644 arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
>  create mode 100644 arch/arm/boot/dts/imx7s-colibri-iris.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b711d4423b42..5a9c805dbc84 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -726,8 +726,12 @@ dtb-$(CONFIG_SOC_IMX7D) += \
>         imx7d-cl-som-imx7.dtb \
>         imx7d-colibri-aster.dtb \
>         imx7d-colibri-emmc-aster.dtb \
> +       imx7d-colibri-emmc-iris.dtb \
> +       imx7d-colibri-emmc-iris-v2.dtb \
>         imx7d-colibri-emmc-eval-v3.dtb \
>         imx7d-colibri-eval-v3.dtb \
> +       imx7d-colibri-iris.dtb \
> +       imx7d-colibri-iris-v2.dtb \
>         imx7d-flex-concentrator.dtb \
>         imx7d-flex-concentrator-mfg.dtb \
>         imx7d-mba7.dtb \
> @@ -747,6 +751,8 @@ dtb-$(CONFIG_SOC_IMX7D) += \
>         imx7d-zii-rpu2.dtb \
>         imx7s-colibri-aster.dtb \
>         imx7s-colibri-eval-v3.dtb \
> +       imx7s-colibri-iris.dtb \
> +       imx7s-colibri-iris-v2.dtb \
>         imx7s-mba7.dtb \
>         imx7s-warp.dtb
>  dtb-$(CONFIG_SOC_IMX7ULP) += \
> diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
> index cf77d894f6d7..6e048d696c77 100644
> --- a/arch/arm/boot/dts/imx6dl-colibri-iris.dts
> +++ b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
> @@ -40,11 +40,10 @@ &gpio2 {
>         pinctrl-0 = <&pinctrl_uart1_forceoff &pinctrl_uart23_forceoff>;
>  
>         /*
> -        * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
> -        * wants to turn the transceiver off, that property has to be deleted
> -        * and the gpio handled in userspace.
> -        * The same applies to uart-b-c-on-x14-enable where the UART_B and
> -        * UART_C transceiver is turned on.
> +        * uart-a-on-x13-enable-hog turns the UART transceiver for UART_A on. If one wants to turn
> +        * the transceiver off, that property has to be deleted and the gpio handled in userspace.
> +        * The same applies to uart-b-c-on-x14-enable-hog where the UART_B and UART_C transceiver is
> +        * turned on.
>          */
>         uart-a-on-x13-enable-hog {
>                 gpio-hog;

Yes, that change to arch/arm/boot/dts/imx6dl-colibri-iris.dts slipped into this Colibri iMX7 specific patch set
by error and will be removed in an upcoming V2. Sorry about that.

[snip]
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b711d4423b42..5a9c805dbc84 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -726,8 +726,12 @@  dtb-$(CONFIG_SOC_IMX7D) += \
 	imx7d-cl-som-imx7.dtb \
 	imx7d-colibri-aster.dtb \
 	imx7d-colibri-emmc-aster.dtb \
+	imx7d-colibri-emmc-iris.dtb \
+	imx7d-colibri-emmc-iris-v2.dtb \
 	imx7d-colibri-emmc-eval-v3.dtb \
 	imx7d-colibri-eval-v3.dtb \
+	imx7d-colibri-iris.dtb \
+	imx7d-colibri-iris-v2.dtb \
 	imx7d-flex-concentrator.dtb \
 	imx7d-flex-concentrator-mfg.dtb \
 	imx7d-mba7.dtb \
@@ -747,6 +751,8 @@  dtb-$(CONFIG_SOC_IMX7D) += \
 	imx7d-zii-rpu2.dtb \
 	imx7s-colibri-aster.dtb \
 	imx7s-colibri-eval-v3.dtb \
+	imx7s-colibri-iris.dtb \
+	imx7s-colibri-iris-v2.dtb \
 	imx7s-mba7.dtb \
 	imx7s-warp.dtb
 dtb-$(CONFIG_SOC_IMX7ULP) += \
diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
index cf77d894f6d7..6e048d696c77 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-iris.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
@@ -40,11 +40,10 @@  &gpio2 {
 	pinctrl-0 = <&pinctrl_uart1_forceoff &pinctrl_uart23_forceoff>;
 
 	/*
-	 * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
-	 * wants to turn the transceiver off, that property has to be deleted
-	 * and the gpio handled in userspace.
-	 * The same applies to uart-b-c-on-x14-enable where the UART_B and
-	 * UART_C transceiver is turned on.
+	 * uart-a-on-x13-enable-hog turns the UART transceiver for UART_A on. If one wants to turn
+	 * the transceiver off, that property has to be deleted and the gpio handled in userspace.
+	 * The same applies to uart-b-c-on-x14-enable-hog where the UART_B and UART_C transceiver is
+	 * turned on.
 	 */
 	uart-a-on-x13-enable-hog {
 		gpio-hog;
diff --git a/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi b/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..6e199613583c
--- /dev/null
+++ b/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
@@ -0,0 +1,112 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* SODIMM 100 */
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart_b_c_on_x14_enable turns the UART transceiver for UART2 and 5 on. If one wants to
+	 * turn the transceiver off, that property has to be deleted and the gpio handled in
+	 * userspace.
+	 * The same applies to uart_a_on_x13_enable where the UART_A transceiver is turned on.
+	 */
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Colibri MMC/SD, UHS-I capable uSD slot */
+&usdhc1 {
+	cap-power-off-card;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7-colibri-iris.dtsi b/arch/arm/boot/dts/imx7-colibri-iris.dtsi
new file mode 100644
index 000000000000..175c5d478d2e
--- /dev/null
+++ b/arch/arm/boot/dts/imx7-colibri-iris.dtsi
@@ -0,0 +1,108 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled in userspace.
+	 * The same applies to uart1_tx_on where the UART1 transceiver is turned on.
+	 */
+	uart25-tx-on-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart1-tx-on-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..7347659557f3
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
@@ -0,0 +1,21 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris-v2",
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..5324c92e368d
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
@@ -0,0 +1,21 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris",
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts b/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
new file mode 100644
index 000000000000..5762f51d5f0f
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
@@ -0,0 +1,83 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris-v2",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-iris.dts b/arch/arm/boot/dts/imx7d-colibri-iris.dts
new file mode 100644
index 000000000000..9c63cb9d9a64
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-iris.dts
@@ -0,0 +1,56 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts b/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
new file mode 100644
index 000000000000..72b5c17ab1ab
--- /dev/null
+++ b/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
@@ -0,0 +1,78 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris-v2",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-iris.dts b/arch/arm/boot/dts/imx7s-colibri-iris.dts
new file mode 100644
index 000000000000..26ba72c17feb
--- /dev/null
+++ b/arch/arm/boot/dts/imx7s-colibri-iris.dts
@@ -0,0 +1,51 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};