diff mbox series

[v8,2/3] arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board

Message ID 20220515233047.531979-3-chris.packham@alliedtelesis.co.nz (mailing list archive)
State New, archived
Headers show
Series arm64: mvebu: Support for Marvell 98DX2530 (and variants) | expand

Commit Message

Chris Packham May 15, 2022, 11:30 p.m. UTC
The 98DX2530 SoC is the Control and Management CPU integrated into
the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
referred to as AlleyCat5 and AlleyCat5X).

These files have been taken from the Marvell SDK and lightly cleaned
up with the License and copyright retained.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Notes:
    The Marvell SDK has a number of new compatible strings. I've brought
    through some of the drivers or where possible used an in-tree
    alternative (e.g. there is SDK code for a ac5-gpio but two instances of
    the existing marvell,orion-gpio seems to cover what is needed if you use
    an appropriate binding). I expect that there will a new series of
    patches when I get some different hardware (or additions to this series
    depending on if/when it lands).
    
    Changes in v8:
    - Remove unnecessary clock-frequency property on armv8-timer
    - Remove unnecessary redistributor-stride property on gic
    - Add GIC_SPI interrupts for gpios
    Changes in v7:
    - Add missing compatible on usb1
    - Add "rd-ac5x" compatible for board
    - Move aliases to board dts
    - Move board specific usb info to board dts
    - Consolidate usb1 board settings and remove unnecessary compatible
    - Add Allied Telesis copyright
    - Rename files after mailng-list discussion
    Changes in v6:
    - Move CPU nodes above the SoC (Krzysztof)
    - Minor formatting clean ups (Krzysztof)
    - Run through `make dtbs_check`
    - Move gic nodes inside SoC
    - Group clocks under a clock node
    Changes in v5:
    - add #{address,size}-cells property to i2c nodes
    - make i2c nodes disabled in the SoC and enable them in the board
    - add interrupt controller attributes to gpio nodes
    - Move fixed-clock nodes up a level and remove unnecessary @0
    Changes in v4:
    - use 'phy-handle' instead of 'phy'
    - move status="okay" on usb nodes to board dts
    - Add review from Andrew
    Changes in v3:
    - Move memory node to board
    - Use single digit reg value for phy address
    - Remove MMC node (driver needs work)
    - Remove syscon & simple-mfd for pinctrl
    Changes in v2:
    - Make pinctrl a child node of a syscon node
    - Use marvell,armada-8k-gpio instead of orion-gpio
    - Remove nand peripheral. The Marvell SDK does have some changes for the
      ac5-nand-controller but I currently lack hardware with NAND fitted so
      I can't test it right now. I've therefore chosen to omit the node and
      not attempted to bring in the driver or binding.
    - Remove pcie peripheral. Again there are changes in the SDK and I have
      no way of testing them.
    - Remove prestera node.
    - Remove "marvell,ac5-ehci" compatible from USB node as
      "marvell,orion-ehci" is sufficient
    - Remove watchdog node. There is a buggy driver for the ac5 watchdog in
      the SDK but it needs some work so I've dropped the node for now.

 arch/arm64/boot/dts/marvell/Makefile          |   1 +
 .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
 .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
 .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +
 4 files changed, 412 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
 create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi

Comments

Chris Packham May 17, 2022, 11:14 p.m. UTC | #1
Hi All,

On 16/05/22 11:30, Chris Packham wrote:
> The 98DX2530 SoC is the Control and Management CPU integrated into
> the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
> referred to as AlleyCat5 and AlleyCat5X).
>
> These files have been taken from the Marvell SDK and lightly cleaned
> up with the License and copyright retained.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> ---

I've been in touch with some of the team at Marvell. They have some 
additions that should hopefully resolve some of the queries/concerns 
around the clock configuration. I've also got a minor update to add a 
comment about the PPI for the EL2 virtual timer based on Marc's request.

I expect to send a v9 with those changes (and anything else anyone has 
feedback on related to this series) sometime next week.

>
> Notes:
>      The Marvell SDK has a number of new compatible strings. I've brought
>      through some of the drivers or where possible used an in-tree
>      alternative (e.g. there is SDK code for a ac5-gpio but two instances of
>      the existing marvell,orion-gpio seems to cover what is needed if you use
>      an appropriate binding). I expect that there will a new series of
>      patches when I get some different hardware (or additions to this series
>      depending on if/when it lands).
>      
>      Changes in v8:
>      - Remove unnecessary clock-frequency property on armv8-timer
>      - Remove unnecessary redistributor-stride property on gic
>      - Add GIC_SPI interrupts for gpios
>      Changes in v7:
>      - Add missing compatible on usb1
>      - Add "rd-ac5x" compatible for board
>      - Move aliases to board dts
>      - Move board specific usb info to board dts
>      - Consolidate usb1 board settings and remove unnecessary compatible
>      - Add Allied Telesis copyright
>      - Rename files after mailng-list discussion
>      Changes in v6:
>      - Move CPU nodes above the SoC (Krzysztof)
>      - Minor formatting clean ups (Krzysztof)
>      - Run through `make dtbs_check`
>      - Move gic nodes inside SoC
>      - Group clocks under a clock node
>      Changes in v5:
>      - add #{address,size}-cells property to i2c nodes
>      - make i2c nodes disabled in the SoC and enable them in the board
>      - add interrupt controller attributes to gpio nodes
>      - Move fixed-clock nodes up a level and remove unnecessary @0
>      Changes in v4:
>      - use 'phy-handle' instead of 'phy'
>      - move status="okay" on usb nodes to board dts
>      - Add review from Andrew
>      Changes in v3:
>      - Move memory node to board
>      - Use single digit reg value for phy address
>      - Remove MMC node (driver needs work)
>      - Remove syscon & simple-mfd for pinctrl
>      Changes in v2:
>      - Make pinctrl a child node of a syscon node
>      - Use marvell,armada-8k-gpio instead of orion-gpio
>      - Remove nand peripheral. The Marvell SDK does have some changes for the
>        ac5-nand-controller but I currently lack hardware with NAND fitted so
>        I can't test it right now. I've therefore chosen to omit the node and
>        not attempted to bring in the driver or binding.
>      - Remove pcie peripheral. Again there are changes in the SDK and I have
>        no way of testing them.
>      - Remove prestera node.
>      - Remove "marvell,ac5-ehci" compatible from USB node as
>        "marvell,orion-ehci" is sufficient
>      - Remove watchdog node. There is a buggy driver for the ac5 watchdog in
>        the SDK but it needs some work so I've dropped the node for now.
>
>   arch/arm64/boot/dts/marvell/Makefile          |   1 +
>   .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
>   .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
>   .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +
>   4 files changed, 412 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 1c794cdcb8e6..b7a4c715afbb 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -24,3 +24,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
>   dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
>   dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
>   dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-98dx35xx-rd.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
> new file mode 100644
> index 000000000000..88edc741c008
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
> @@ -0,0 +1,297 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree For AC5.
> + *
> + * Copyright (C) 2021 Marvell
> + * Copyright (C) 2022 Allied Telesis Labs
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +	model = "Marvell AC5 SoC";
> +	compatible = "marvell,ac5";
> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	cpus {
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&cpu0>;
> +				};
> +				core1 {
> +					cpu = <&cpu1>;
> +				};
> +			};
> +		};
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,armv8";
> +			reg = <0x0 0x0>;
> +			enable-method = "psci";
> +			next-level-cache = <&l2>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,armv8";
> +			reg = <0x0 0x100>;
> +			enable-method = "psci";
> +			next-level-cache = <&l2>;
> +		};
> +
> +		l2: l2-cache {
> +			compatible = "cache";
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	pmu {
> +		compatible = "arm,armv8-pmuv3";
> +		interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	soc {
> +		compatible = "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		dma-ranges;
> +
> +		internal-regs@7f000000 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			compatible = "simple-bus";
> +			/* 16M internal register @ 0x7f00_0000 */
> +			ranges = <0x0 0x0 0x7f000000 0x1000000>;
> +			dma-coherent;
> +
> +			uart0: serial@12000 {
> +				compatible = "snps,dw-apb-uart";
> +				reg = <0x12000 0x100>;
> +				reg-shift = <2>;
> +				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +				reg-io-width = <1>;
> +				clock-frequency = <328000000>;
> +				status = "okay";
> +			};
> +
> +			mdio: mdio@22004 {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				compatible = "marvell,orion-mdio";
> +				reg = <0x22004 0x4>;
> +				clocks = <&core_clock>;
> +			};
> +
> +			i2c0: i2c@11000{
> +				compatible = "marvell,mv78230-i2c";
> +				reg = <0x11000 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				clocks = <&core_clock>;
> +				clock-names = "core";
> +				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
> +				clock-frequency=<100000>;
> +
> +				pinctrl-names = "default", "gpio";
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-1 = <&i2c0_gpio>;
> +				scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
> +				sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
> +				status = "disabled";
> +			};
> +
> +			i2c1: i2c@11100{
> +				compatible = "marvell,mv78230-i2c";
> +				reg = <0x11100 0x20>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				clocks = <&core_clock>;
> +				clock-names = "core";
> +				interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> +				clock-frequency=<100000>;
> +
> +				pinctrl-names = "default", "gpio";
> +				pinctrl-0 = <&i2c1_pins>;
> +				pinctrl-1 = <&i2c1_gpio>;
> +				scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
> +				sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
> +				status = "disabled";
> +			};
> +
> +			gpio0: gpio@18100 {
> +				compatible = "marvell,orion-gpio";
> +				reg = <0x18100 0x40>;
> +				ngpios = <32>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				gpio-ranges = <&pinctrl0 0 0 32>;
> +				marvell,pwm-offset = <0x1f0>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			gpio1: gpio@18140 {
> +				reg = <0x18140 0x40>;
> +				compatible = "marvell,orion-gpio";
> +				ngpios = <14>;
> +				gpio-controller;
> +				#gpio-cells = <2>;
> +				gpio-ranges = <&pinctrl0 0 32 14>;
> +				marvell,pwm-offset = <0x1f0>;
> +				interrupt-controller;
> +				#interrupt-cells = <2>;
> +				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		/*
> +		 * Dedicated section for devices behind 32bit controllers so we
> +		 * can configure specific DMA mapping for them
> +		 */
> +		behind-32bit-controller@7f000000 {
> +			compatible = "simple-bus";
> +			#address-cells = <0x2>;
> +			#size-cells = <0x2>;
> +			ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
> +			/* Host phy ram starts at 0x200M */
> +			dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
> +			dma-coherent;
> +
> +			eth0: ethernet@20000 {
> +				compatible = "marvell,armada-ac5-neta";
> +				reg = <0x0 0x20000 0x0 0x4000>;
> +				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&core_clock>;
> +				phy-mode = "sgmii";
> +				status = "disabled";
> +			};
> +
> +			eth1: ethernet@24000 {
> +				compatible = "marvell,armada-ac5-neta";
> +				reg = <0x0 0x24000 0x0 0x4000>;
> +				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
> +				clocks = <&core_clock>;
> +				phy-mode = "sgmii";
> +				status = "disabled";
> +			};
> +
> +			usb0: usb@80000 {
> +				compatible = "marvell,orion-ehci";
> +				reg = <0x0 0x80000 0x0 0x500>;
> +				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
> +				status = "disabled";
> +			};
> +
> +			usb1: usb@a0000 {
> +				compatible = "marvell,orion-ehci";
> +				reg = <0x0 0xa0000 0x0 0x500>;
> +				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		pinctrl0: pinctrl@80020100 {
> +			compatible = "marvell,ac5-pinctrl";
> +			reg = <0 0x80020100 0 0x20>;
> +
> +			i2c0_pins: i2c0-pins {
> +				marvell,pins = "mpp26", "mpp27";
> +				marvell,function = "i2c0";
> +			};
> +
> +			i2c0_gpio: i2c0-gpio-pins {
> +				marvell,pins = "mpp26", "mpp27";
> +				marvell,function = "gpio";
> +			};
> +
> +			i2c1_pins: i2c1-pins {
> +				marvell,pins = "mpp20", "mpp21";
> +				marvell,function = "i2c1";
> +			};
> +
> +			i2c1_gpio: i2c1-gpio-pins {
> +				marvell,pins = "mpp20", "mpp21";
> +				marvell,function = "i2c1";
> +			};
> +		};
> +
> +		spi0: spi@805a0000 {
> +			compatible = "marvell,armada-3700-spi";
> +			reg = <0x0 0x805a0000 0x0 0x50>;
> +			#address-cells = <0x1>;
> +			#size-cells = <0x0>;
> +			clocks = <&spi_clock>;
> +			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
> +			num-cs = <1>;
> +			status = "disabled";
> +		};
> +
> +		spi1: spi@805a8000 {
> +			compatible = "marvell,armada-3700-spi";
> +			reg = <0x0 0x805a8000 0x0 0x50>;
> +			#address-cells = <0x1>;
> +			#size-cells = <0x0>;
> +			clocks = <&spi_clock>;
> +			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
> +			num-cs = <1>;
> +			status = "disabled";
> +		};
> +
> +		gic: interrupt-controller@80600000 {
> +			compatible = "arm,gic-v3";
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
> +			      <0x0 0x80660000 0x0 0x40000>; /* GICR */
> +			interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +	};
> +
> +	clocks {
> +		core_clock: core-clock {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <400000000>;
> +		};
> +
> +		axi_clock: axi-clock {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <325000000>;
> +		};
> +
> +		spi_clock: spi-clock {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <200000000>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
> new file mode 100644
> index 000000000000..c20e032410fa
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
> @@ -0,0 +1,101 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree For RD-AC5X.
> + *
> + * Copyright (C) 2021 Marvell
> + * Copyright (C) 2022 Allied Telesis Labs
> + */
> +/*
> + * Device Tree file for Marvell Alleycat 5X development board
> + * This board file supports the B configuration of the board
> + */
> +
> +/dts-v1/;
> +
> +#include "armada-98dx35xx.dtsi"
> +
> +/ {
> +	model = "Marvell RD-AC5X Board";
> +	compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		spiflash0 = &spiflash0;
> +		gpio0 = &gpio0;
> +		gpio1 = &gpio1;
> +		ethernet0 = &eth0;
> +		ethernet1 = &eth1;
> +	};
> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x2 0x00000000 0x0 0x40000000>;
> +	};
> +
> +	usb1phy: usb-phy {
> +		compatible = "usb-nop-xceiv";
> +		#phy-cells = <0>;
> +	};
> +};
> +
> +&mdio {
> +	phy0: ethernet-phy@0 {
> +		reg = <0>;
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +};
> +
> +&eth0 {
> +	status = "okay";
> +	phy-handle = <&phy0>;
> +};
> +
> +/* USB0 is a host USB */
> +&usb0 {
> +	status = "okay";
> +};
> +
> +/* USB1 is a peripheral USB */
> +&usb1 {
> +	status = "okay";
> +	phys = <&usb1phy>;
> +	phy-names = "usb-phy";
> +	dr_mode = "peripheral";
> +};
> +
> +&spi0 {
> +	status = "okay";
> +
> +	spiflash0: flash@0 {
> +		compatible = "jedec,spi-nor";
> +		spi-max-frequency = <50000000>;
> +		spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
> +		spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
> +		reg = <0>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +		partition@0 {
> +			label = "spi_flash_part0";
> +			reg = <0x0 0x800000>;
> +		};
> +
> +		parition@1 {
> +			label = "spi_flash_part1";
> +			reg = <0x800000 0x700000>;
> +		};
> +
> +		parition@2 {
> +			label = "spi_flash_part2";
> +			reg = <0xF00000 0x100000>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
> new file mode 100644
> index 000000000000..62d2650513aa
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
> @@ -0,0 +1,13 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree For AC5X.
> + *
> + * Copyright (C) 2022 Allied Telesis Labs
> + */
> +
> +#include "armada-98dx25xx.dtsi"
> +
> +/ {
> +	model = "Marvell AC5X SoC";
> +	compatible = "marvell,ac5x", "marvell,ac5";
> +};
Chris Packham May 26, 2022, 10:46 p.m. UTC | #2
Hi All,

On 18/05/22 11:14, Chris Packham wrote:
> Hi All,
>
> On 16/05/22 11:30, Chris Packham wrote:
>> The 98DX2530 SoC is the Control and Management CPU integrated into
>> the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
>> referred to as AlleyCat5 and AlleyCat5X).
>>
>> These files have been taken from the Marvell SDK and lightly cleaned
>> up with the License and copyright retained.
>>
>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
>> ---
>
> I've been in touch with some of the team at Marvell. They have some 
> additions that should hopefully resolve some of the queries/concerns 
> around the clock configuration. I've also got a minor update to add a 
> comment about the PPI for the EL2 virtual timer based on Marc's request.
>
> I expect to send a v9 with those changes (and anything else anyone has 
> feedback on related to this series) sometime next week.

I had a good conversation with Elad, Vadym and Serhiy.

The plan is for them to take over this series and get it driven to 
completion. We've missed the merge window for 5.19 but hopefully we can 
get things in for 5.20.

We expect to see another name change away from "armada" (the Alleycat5 
CnM block doesn't really bear much resemblance to the Armada-3700 aside 
from the odd peripheral).

There should also be some clarification around the clocking. As I 
expected there really are just some fixed dividers in the hardware that 
take the single 25MHz reference clock to supply clocks for the various 
peripherals. There is no gating or dynamic scaling possible so these are 
just represented as fixed-clock nodes.

>
>>
>> Notes:
>>      The Marvell SDK has a number of new compatible strings. I've 
>> brought
>>      through some of the drivers or where possible used an in-tree
>>      alternative (e.g. there is SDK code for a ac5-gpio but two 
>> instances of
>>      the existing marvell,orion-gpio seems to cover what is needed if 
>> you use
>>      an appropriate binding). I expect that there will a new series of
>>      patches when I get some different hardware (or additions to this 
>> series
>>      depending on if/when it lands).
>>           Changes in v8:
>>      - Remove unnecessary clock-frequency property on armv8-timer
>>      - Remove unnecessary redistributor-stride property on gic
>>      - Add GIC_SPI interrupts for gpios
>>      Changes in v7:
>>      - Add missing compatible on usb1
>>      - Add "rd-ac5x" compatible for board
>>      - Move aliases to board dts
>>      - Move board specific usb info to board dts
>>      - Consolidate usb1 board settings and remove unnecessary compatible
>>      - Add Allied Telesis copyright
>>      - Rename files after mailng-list discussion
>>      Changes in v6:
>>      - Move CPU nodes above the SoC (Krzysztof)
>>      - Minor formatting clean ups (Krzysztof)
>>      - Run through `make dtbs_check`
>>      - Move gic nodes inside SoC
>>      - Group clocks under a clock node
>>      Changes in v5:
>>      - add #{address,size}-cells property to i2c nodes
>>      - make i2c nodes disabled in the SoC and enable them in the board
>>      - add interrupt controller attributes to gpio nodes
>>      - Move fixed-clock nodes up a level and remove unnecessary @0
>>      Changes in v4:
>>      - use 'phy-handle' instead of 'phy'
>>      - move status="okay" on usb nodes to board dts
>>      - Add review from Andrew
>>      Changes in v3:
>>      - Move memory node to board
>>      - Use single digit reg value for phy address
>>      - Remove MMC node (driver needs work)
>>      - Remove syscon & simple-mfd for pinctrl
>>      Changes in v2:
>>      - Make pinctrl a child node of a syscon node
>>      - Use marvell,armada-8k-gpio instead of orion-gpio
>>      - Remove nand peripheral. The Marvell SDK does have some changes 
>> for the
>>        ac5-nand-controller but I currently lack hardware with NAND 
>> fitted so
>>        I can't test it right now. I've therefore chosen to omit the 
>> node and
>>        not attempted to bring in the driver or binding.
>>      - Remove pcie peripheral. Again there are changes in the SDK and 
>> I have
>>        no way of testing them.
>>      - Remove prestera node.
>>      - Remove "marvell,ac5-ehci" compatible from USB node as
>>        "marvell,orion-ehci" is sufficient
>>      - Remove watchdog node. There is a buggy driver for the ac5 
>> watchdog in
>>        the SDK but it needs some work so I've dropped the node for now.
>>
>>   arch/arm64/boot/dts/marvell/Makefile          |   1 +
>>   .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
>>   .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
>>   .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +
>>   4 files changed, 412 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
>>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
>>   create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/marvell/Makefile 
>> b/arch/arm64/boot/dts/marvell/Makefile
>> index 1c794cdcb8e6..b7a4c715afbb 100644
>> --- a/arch/arm64/boot/dts/marvell/Makefile
>> +++ b/arch/arm64/boot/dts/marvell/Makefile
>> @@ -24,3 +24,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
>>   dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
>>   dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
>>   dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
>> +dtb-$(CONFIG_ARCH_MVEBU) += armada-98dx35xx-rd.dtb
>> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi 
>> b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
>> new file mode 100644
>> index 000000000000..88edc741c008
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
>> @@ -0,0 +1,297 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Device Tree For AC5.
>> + *
>> + * Copyright (C) 2021 Marvell
>> + * Copyright (C) 2022 Allied Telesis Labs
>> + */
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +
>> +/ {
>> +    model = "Marvell AC5 SoC";
>> +    compatible = "marvell,ac5";
>> +    interrupt-parent = <&gic>;
>> +    #address-cells = <2>;
>> +    #size-cells = <2>;
>> +
>> +    cpus {
>> +        #address-cells = <2>;
>> +        #size-cells = <0>;
>> +
>> +        cpu-map {
>> +            cluster0 {
>> +                core0 {
>> +                    cpu = <&cpu0>;
>> +                };
>> +                core1 {
>> +                    cpu = <&cpu1>;
>> +                };
>> +            };
>> +        };
>> +
>> +        cpu0: cpu@0 {
>> +            device_type = "cpu";
>> +            compatible = "arm,armv8";
>> +            reg = <0x0 0x0>;
>> +            enable-method = "psci";
>> +            next-level-cache = <&l2>;
>> +        };
>> +
>> +        cpu1: cpu@1 {
>> +            device_type = "cpu";
>> +            compatible = "arm,armv8";
>> +            reg = <0x0 0x100>;
>> +            enable-method = "psci";
>> +            next-level-cache = <&l2>;
>> +        };
>> +
>> +        l2: l2-cache {
>> +            compatible = "cache";
>> +        };
>> +    };
>> +
>> +    psci {
>> +        compatible = "arm,psci-0.2";
>> +        method = "smc";
>> +    };
>> +
>> +    timer {
>> +        compatible = "arm,armv8-timer";
>> +        interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
>> +                 <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> +                 <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
>> +                 <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> +    };
>> +
>> +    pmu {
>> +        compatible = "arm,armv8-pmuv3";
>> +        interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> +    };
>> +
>> +    soc {
>> +        compatible = "simple-bus";
>> +        #address-cells = <2>;
>> +        #size-cells = <2>;
>> +        ranges;
>> +        dma-ranges;
>> +
>> +        internal-regs@7f000000 {
>> +            #address-cells = <1>;
>> +            #size-cells = <1>;
>> +            compatible = "simple-bus";
>> +            /* 16M internal register @ 0x7f00_0000 */
>> +            ranges = <0x0 0x0 0x7f000000 0x1000000>;
>> +            dma-coherent;
>> +
>> +            uart0: serial@12000 {
>> +                compatible = "snps,dw-apb-uart";
>> +                reg = <0x12000 0x100>;
>> +                reg-shift = <2>;
>> +                interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
>> +                reg-io-width = <1>;
>> +                clock-frequency = <328000000>;
>> +                status = "okay";
>> +            };
>> +
>> +            mdio: mdio@22004 {
>> +                #address-cells = <1>;
>> +                #size-cells = <0>;
>> +                compatible = "marvell,orion-mdio";
>> +                reg = <0x22004 0x4>;
>> +                clocks = <&core_clock>;
>> +            };
>> +
>> +            i2c0: i2c@11000{
>> +                compatible = "marvell,mv78230-i2c";
>> +                reg = <0x11000 0x20>;
>> +                #address-cells = <1>;
>> +                #size-cells = <0>;
>> +
>> +                clocks = <&core_clock>;
>> +                clock-names = "core";
>> +                interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
>> +                clock-frequency=<100000>;
>> +
>> +                pinctrl-names = "default", "gpio";
>> +                pinctrl-0 = <&i2c0_pins>;
>> +                pinctrl-1 = <&i2c0_gpio>;
>> +                scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
>> +                sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
>> +                status = "disabled";
>> +            };
>> +
>> +            i2c1: i2c@11100{
>> +                compatible = "marvell,mv78230-i2c";
>> +                reg = <0x11100 0x20>;
>> +                #address-cells = <1>;
>> +                #size-cells = <0>;
>> +
>> +                clocks = <&core_clock>;
>> +                clock-names = "core";
>> +                interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
>> +                clock-frequency=<100000>;
>> +
>> +                pinctrl-names = "default", "gpio";
>> +                pinctrl-0 = <&i2c1_pins>;
>> +                pinctrl-1 = <&i2c1_gpio>;
>> +                scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
>> +                sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
>> +                status = "disabled";
>> +            };
>> +
>> +            gpio0: gpio@18100 {
>> +                compatible = "marvell,orion-gpio";
>> +                reg = <0x18100 0x40>;
>> +                ngpios = <32>;
>> +                gpio-controller;
>> +                #gpio-cells = <2>;
>> +                gpio-ranges = <&pinctrl0 0 0 32>;
>> +                marvell,pwm-offset = <0x1f0>;
>> +                interrupt-controller;
>> +                #interrupt-cells = <2>;
>> +                interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
>> +            };
>> +
>> +            gpio1: gpio@18140 {
>> +                reg = <0x18140 0x40>;
>> +                compatible = "marvell,orion-gpio";
>> +                ngpios = <14>;
>> +                gpio-controller;
>> +                #gpio-cells = <2>;
>> +                gpio-ranges = <&pinctrl0 0 32 14>;
>> +                marvell,pwm-offset = <0x1f0>;
>> +                interrupt-controller;
>> +                #interrupt-cells = <2>;
>> +                interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
>> +                         <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
>> +            };
>> +        };
>> +
>> +        /*
>> +         * Dedicated section for devices behind 32bit controllers so we
>> +         * can configure specific DMA mapping for them
>> +         */
>> +        behind-32bit-controller@7f000000 {
>> +            compatible = "simple-bus";
>> +            #address-cells = <0x2>;
>> +            #size-cells = <0x2>;
>> +            ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
>> +            /* Host phy ram starts at 0x200M */
>> +            dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
>> +            dma-coherent;
>> +
>> +            eth0: ethernet@20000 {
>> +                compatible = "marvell,armada-ac5-neta";
>> +                reg = <0x0 0x20000 0x0 0x4000>;
>> +                interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
>> +                clocks = <&core_clock>;
>> +                phy-mode = "sgmii";
>> +                status = "disabled";
>> +            };
>> +
>> +            eth1: ethernet@24000 {
>> +                compatible = "marvell,armada-ac5-neta";
>> +                reg = <0x0 0x24000 0x0 0x4000>;
>> +                interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
>> +                clocks = <&core_clock>;
>> +                phy-mode = "sgmii";
>> +                status = "disabled";
>> +            };
>> +
>> +            usb0: usb@80000 {
>> +                compatible = "marvell,orion-ehci";
>> +                reg = <0x0 0x80000 0x0 0x500>;
>> +                interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
>> +                status = "disabled";
>> +            };
>> +
>> +            usb1: usb@a0000 {
>> +                compatible = "marvell,orion-ehci";
>> +                reg = <0x0 0xa0000 0x0 0x500>;
>> +                interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
>> +                status = "disabled";
>> +            };
>> +        };
>> +
>> +        pinctrl0: pinctrl@80020100 {
>> +            compatible = "marvell,ac5-pinctrl";
>> +            reg = <0 0x80020100 0 0x20>;
>> +
>> +            i2c0_pins: i2c0-pins {
>> +                marvell,pins = "mpp26", "mpp27";
>> +                marvell,function = "i2c0";
>> +            };
>> +
>> +            i2c0_gpio: i2c0-gpio-pins {
>> +                marvell,pins = "mpp26", "mpp27";
>> +                marvell,function = "gpio";
>> +            };
>> +
>> +            i2c1_pins: i2c1-pins {
>> +                marvell,pins = "mpp20", "mpp21";
>> +                marvell,function = "i2c1";
>> +            };
>> +
>> +            i2c1_gpio: i2c1-gpio-pins {
>> +                marvell,pins = "mpp20", "mpp21";
>> +                marvell,function = "i2c1";
>> +            };
>> +        };
>> +
>> +        spi0: spi@805a0000 {
>> +            compatible = "marvell,armada-3700-spi";
>> +            reg = <0x0 0x805a0000 0x0 0x50>;
>> +            #address-cells = <0x1>;
>> +            #size-cells = <0x0>;
>> +            clocks = <&spi_clock>;
>> +            interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
>> +            num-cs = <1>;
>> +            status = "disabled";
>> +        };
>> +
>> +        spi1: spi@805a8000 {
>> +            compatible = "marvell,armada-3700-spi";
>> +            reg = <0x0 0x805a8000 0x0 0x50>;
>> +            #address-cells = <0x1>;
>> +            #size-cells = <0x0>;
>> +            clocks = <&spi_clock>;
>> +            interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
>> +            num-cs = <1>;
>> +            status = "disabled";
>> +        };
>> +
>> +        gic: interrupt-controller@80600000 {
>> +            compatible = "arm,gic-v3";
>> +            #interrupt-cells = <3>;
>> +            interrupt-controller;
>> +            reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
>> +                  <0x0 0x80660000 0x0 0x40000>; /* GICR */
>> +            interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
>> +        };
>> +    };
>> +
>> +    clocks {
>> +        core_clock: core-clock {
>> +            compatible = "fixed-clock";
>> +            #clock-cells = <0>;
>> +            clock-frequency = <400000000>;
>> +        };
>> +
>> +        axi_clock: axi-clock {
>> +            compatible = "fixed-clock";
>> +            #clock-cells = <0>;
>> +            clock-frequency = <325000000>;
>> +        };
>> +
>> +        spi_clock: spi-clock {
>> +            compatible = "fixed-clock";
>> +            #clock-cells = <0>;
>> +            clock-frequency = <200000000>;
>> +        };
>> +    };
>> +};
>> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts 
>> b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
>> new file mode 100644
>> index 000000000000..c20e032410fa
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
>> @@ -0,0 +1,101 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Device Tree For RD-AC5X.
>> + *
>> + * Copyright (C) 2021 Marvell
>> + * Copyright (C) 2022 Allied Telesis Labs
>> + */
>> +/*
>> + * Device Tree file for Marvell Alleycat 5X development board
>> + * This board file supports the B configuration of the board
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "armada-98dx35xx.dtsi"
>> +
>> +/ {
>> +    model = "Marvell RD-AC5X Board";
>> +    compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
>> +
>> +    aliases {
>> +        serial0 = &uart0;
>> +        spiflash0 = &spiflash0;
>> +        gpio0 = &gpio0;
>> +        gpio1 = &gpio1;
>> +        ethernet0 = &eth0;
>> +        ethernet1 = &eth1;
>> +    };
>> +
>> +    memory@0 {
>> +        device_type = "memory";
>> +        reg = <0x2 0x00000000 0x0 0x40000000>;
>> +    };
>> +
>> +    usb1phy: usb-phy {
>> +        compatible = "usb-nop-xceiv";
>> +        #phy-cells = <0>;
>> +    };
>> +};
>> +
>> +&mdio {
>> +    phy0: ethernet-phy@0 {
>> +        reg = <0>;
>> +    };
>> +};
>> +
>> +&i2c0 {
>> +    status = "okay";
>> +};
>> +
>> +&i2c1 {
>> +    status = "okay";
>> +};
>> +
>> +&eth0 {
>> +    status = "okay";
>> +    phy-handle = <&phy0>;
>> +};
>> +
>> +/* USB0 is a host USB */
>> +&usb0 {
>> +    status = "okay";
>> +};
>> +
>> +/* USB1 is a peripheral USB */
>> +&usb1 {
>> +    status = "okay";
>> +    phys = <&usb1phy>;
>> +    phy-names = "usb-phy";
>> +    dr_mode = "peripheral";
>> +};
>> +
>> +&spi0 {
>> +    status = "okay";
>> +
>> +    spiflash0: flash@0 {
>> +        compatible = "jedec,spi-nor";
>> +        spi-max-frequency = <50000000>;
>> +        spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
>> +        spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
>> +        reg = <0>;
>> +
>> +        #address-cells = <1>;
>> +        #size-cells = <1>;
>> +
>> +        partition@0 {
>> +            label = "spi_flash_part0";
>> +            reg = <0x0 0x800000>;
>> +        };
>> +
>> +        parition@1 {
>> +            label = "spi_flash_part1";
>> +            reg = <0x800000 0x700000>;
>> +        };
>> +
>> +        parition@2 {
>> +            label = "spi_flash_part2";
>> +            reg = <0xF00000 0x100000>;
>> +        };
>> +    };
>> +};
>> diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi 
>> b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
>> new file mode 100644
>> index 000000000000..62d2650513aa
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
>> @@ -0,0 +1,13 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Device Tree For AC5X.
>> + *
>> + * Copyright (C) 2022 Allied Telesis Labs
>> + */
>> +
>> +#include "armada-98dx25xx.dtsi"
>> +
>> +/ {
>> +    model = "Marvell AC5X SoC";
>> +    compatible = "marvell,ac5x", "marvell,ac5";
>> +};
Vadym Kochan June 7, 2022, 11:49 a.m. UTC | #3
Hi All,

> arch/arm64/boot/dts/marvell/Makefile          |   1 +
> .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
> .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
> .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +

There is a proposal from the Marvell to replace "armada-" prefix to "ac5-" in DTS naming as there
is no much common with Armada SoC's.

Regards,
Vadym Kochan
Andrew Lunn June 7, 2022, 12:07 p.m. UTC | #4
On Tue, Jun 07, 2022 at 02:49:36PM +0300, Vadym Kochan wrote:
> Hi All,
> 
> > arch/arm64/boot/dts/marvell/Makefile          |   1 +
> > .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
> > .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
> > .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +
> 
> There is a proposal from the Marvell to replace "armada-" prefix to "ac5-" in DTS naming as there
> is no much common with Armada SoC's.

O.K. We can do this. But i hope it is not Marvell being lazy.

I can also see an advantage of using armada-, since it makes it clear
we are talking about mainline device tree files, not Marvell vendor
device tree files. It is not given they will be compatible.

       Andrew
Chris Packham June 7, 2022, 9:40 p.m. UTC | #5
On 8/06/22 00:07, Andrew Lunn wrote:
> On Tue, Jun 07, 2022 at 02:49:36PM +0300, Vadym Kochan wrote:
>> Hi All,
>>
>>> arch/arm64/boot/dts/marvell/Makefile          |   1 +
>>> .../boot/dts/marvell/armada-98dx25xx.dtsi     | 297 ++++++++++++++++++
>>> .../boot/dts/marvell/armada-98dx35xx-rd.dts   | 101 ++++++
>>> .../boot/dts/marvell/armada-98dx35xx.dtsi     |  13 +
>> There is a proposal from the Marvell to replace "armada-" prefix to "ac5-" in DTS naming as there
>> is no much common with Armada SoC's.
> O.K. We can do this. But i hope it is not Marvell being lazy.
>
> I can also see an advantage of using armada-, since it makes it clear
> we are talking about mainline device tree files, not Marvell vendor
> device tree files. It is not given they will be compatible.

We'll still have the 98dx25xx suffixes so it should still be distinct 
from the Marvell SDK ones. Also hopefully once this lands upstream it 
will encourage Marvell to update their SDK to a newer kernel.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..b7a4c715afbb 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -24,3 +24,4 @@  dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-98dx35xx-rd.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
new file mode 100644
index 000000000000..88edc741c008
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-98dx25xx.dtsi
@@ -0,0 +1,297 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "Marvell AC5 SoC";
+	compatible = "marvell,ac5";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-ranges;
+
+		internal-regs@7f000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			/* 16M internal register @ 0x7f00_0000 */
+			ranges = <0x0 0x0 0x7f000000 0x1000000>;
+			dma-coherent;
+
+			uart0: serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clock-frequency = <328000000>;
+				status = "okay";
+			};
+
+			mdio: mdio@22004 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x22004 0x4>;
+				clocks = <&core_clock>;
+			};
+
+			i2c0: i2c@11000{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&core_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-1 = <&i2c0_gpio>;
+				scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+				sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&core_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-1 = <&i2c1_gpio>;
+				scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+				sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+				status = "disabled";
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 0 32>;
+				marvell,pwm-offset = <0x1f0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				reg = <0x18140 0x40>;
+				compatible = "marvell,orion-gpio";
+				ngpios = <14>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 32 14>;
+				marvell,pwm-offset = <0x1f0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		/*
+		 * Dedicated section for devices behind 32bit controllers so we
+		 * can configure specific DMA mapping for them
+		 */
+		behind-32bit-controller@7f000000 {
+			compatible = "simple-bus";
+			#address-cells = <0x2>;
+			#size-cells = <0x2>;
+			ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+			/* Host phy ram starts at 0x200M */
+			dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+			dma-coherent;
+
+			eth0: ethernet@20000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x20000 0x0 0x4000>;
+				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&core_clock>;
+				phy-mode = "sgmii";
+				status = "disabled";
+			};
+
+			eth1: ethernet@24000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x24000 0x0 0x4000>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&core_clock>;
+				phy-mode = "sgmii";
+				status = "disabled";
+			};
+
+			usb0: usb@80000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x0 0x80000 0x0 0x500>;
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			usb1: usb@a0000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x0 0xa0000 0x0 0x500>;
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		pinctrl0: pinctrl@80020100 {
+			compatible = "marvell,ac5-pinctrl";
+			reg = <0 0x80020100 0 0x20>;
+
+			i2c0_pins: i2c0-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "i2c0";
+			};
+
+			i2c0_gpio: i2c0-gpio-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "gpio";
+			};
+
+			i2c1_pins: i2c1-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+
+			i2c1_gpio: i2c1-gpio-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+		};
+
+		spi0: spi@805a0000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a0000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		spi1: spi@805a8000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a8000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@80600000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+			      <0x0 0x80660000 0x0 0x40000>; /* GICR */
+			interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	clocks {
+		core_clock: core-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+
+		axi_clock: axi-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <325000000>;
+		};
+
+		spi_clock: spi-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
new file mode 100644
index 000000000000..c20e032410fa
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx-rd.dts
@@ -0,0 +1,101 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For RD-AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "armada-98dx35xx.dtsi"
+
+/ {
+	model = "Marvell RD-AC5X Board";
+	compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
+
+	aliases {
+		serial0 = &uart0;
+		spiflash0 = &spiflash0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x2 0x00000000 0x0 0x40000000>;
+	};
+
+	usb1phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+};
+
+&mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+};
+
+/* USB0 is a host USB */
+&usb0 {
+	status = "okay";
+};
+
+/* USB1 is a peripheral USB */
+&usb1 {
+	status = "okay";
+	phys = <&usb1phy>;
+	phy-names = "usb-phy";
+	dr_mode = "peripheral";
+};
+
+&spi0 {
+	status = "okay";
+
+	spiflash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		reg = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "spi_flash_part0";
+			reg = <0x0 0x800000>;
+		};
+
+		parition@1 {
+			label = "spi_flash_part1";
+			reg = <0x800000 0x700000>;
+		};
+
+		parition@2 {
+			label = "spi_flash_part2";
+			reg = <0xF00000 0x100000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
new file mode 100644
index 000000000000..62d2650513aa
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-98dx35xx.dtsi
@@ -0,0 +1,13 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include "armada-98dx25xx.dtsi"
+
+/ {
+	model = "Marvell AC5X SoC";
+	compatible = "marvell,ac5x", "marvell,ac5";
+};