diff mbox series

[v2,10/24] ARM: dts: imx7-colibri: add delay for on-module phy supply

Message ID 20220516134734.493065-11-marcel@ziswiler.com (mailing list archive)
State New, archived
Headers show
Series ARM: dts: imx7-colibri: device tree improvements | expand

Commit Message

Marcel Ziswiler May 16, 2022, 1:47 p.m. UTC
From: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

There is a significant time required for PHY Micrel KSZ8041 to power up.
Add a delay on start-up/wake-up before the FEC starts communicating with
the PHY.

LDO1 takes 6 ms, R39 + C44 takes ~100ms, the KSZ8041 datasheet asks for
~11 ms before starting any programming on the MIIM.

Counting that, add a 200 ms delay to be sure the PHY is ready for
programming. Also, add the same off delay time to give the capacitor
time to discharge in order to properly reset.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---

(no changes since v1)

 arch/arm/boot/dts/imx7-colibri.dtsi | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 329638985db6..09dbd262dad1 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -94,6 +94,17 @@  reg_module_3v3_avdd: regulator-module-3v3-avdd {
 		regulator-name = "+V3.3_AVDD_AUDIO";
 	};
 
+	reg_module_3v3_eth: regulator-module-3v3-eth {
+		compatible = "regulator-fixed";
+		off-on-delay-us = <200000>;
+		regulator-name = "+V3.3_ETH";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_LDO1>;
+	};
+
 	reg_usbh_vbus: regulator-usbh-vbus {
 		compatible = "regulator-fixed";
 		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
@@ -153,7 +164,7 @@  &fec1 {
 	fsl,magic-packet;
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	phy-supply = <&reg_LDO1>;
+	phy-supply = <&reg_module_3v3_eth>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_enet1>;
 	pinctrl-1 = <&pinctrl_enet1_sleep>;
@@ -440,7 +451,7 @@  reg_DCDC4: DCDC4 { /* V1.35_DRAM */
 			};
 
 			reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
-				regulator-min-microvolt = <1800000>;
+				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 			};