diff mbox series

[v4,2/3] dt-bindings: mfd: atmel,flexcom: Add new compatible string for lan966x

Message ID 20220617130729.12072-3-kavyasree.kotagiri@microchip.com (mailing list archive)
State New, archived
Headers show
Series Add support for lan966x flexcom chip-select configuration | expand

Commit Message

Kavyasree Kotagiri June 17, 2022, 1:07 p.m. UTC 
LAN966x SoC flexcoms has two optional I/O lines. Namely, CS0 and CS1
in flexcom SPI mode. CTS and RTS in flexcom USART mode. These pins
can be mapped to lan966x FLEXCOM_SHARED[0-20] pins and usage depends on
functions being configured.

Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
---
v3 -> v4:
 - Added else condition to allOf:if:then.

v2 -> v3:
 - Add reg property of lan966x missed in v2.

v1 -> v2:
 - Use allOf:if:then for lan966x dt properties

 .../bindings/mfd/atmel,flexcom.yaml           | 80 ++++++++++++++++++-
 1 file changed, 79 insertions(+), 1 deletion(-)

Comments

Rob Herring (Arm) June 17, 2022, 1:58 p.m. UTC | #1 
On Fri, 17 Jun 2022 18:37:28 +0530, Kavyasree Kotagiri wrote:
> LAN966x SoC flexcoms has two optional I/O lines. Namely, CS0 and CS1
> in flexcom SPI mode. CTS and RTS in flexcom USART mode. These pins
> can be mapped to lan966x FLEXCOM_SHARED[0-20] pins and usage depends on
> functions being configured.
> 
> Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
> ---
> v3 -> v4:
>  - Added else condition to allOf:if:then.
> 
> v2 -> v3:
>  - Add reg property of lan966x missed in v2.
> 
> v1 -> v2:
>  - Use allOf:if:then for lan966x dt properties
> 
>  .../bindings/mfd/atmel,flexcom.yaml           | 80 ++++++++++++++++++-
>  1 file changed, 79 insertions(+), 1 deletion(-)
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml: allOf:0:else:properties:reg: {'maxItems': 1, 'items': [{'description': 'Flexcom base regsiters map'}]} should not be valid under {'required': ['maxItems']}
	hint: "maxItems" is not needed with an "items" list
	from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml: allOf:0:then:properties:reg: 'oneOf' conditional failed, one must be fixed:
	[{'description': 'Flexcom base regsiters map'}, {'description': 'Flexcom shared registers map'}] is too long
	[{'description': 'Flexcom base regsiters map'}, {'description': 'Flexcom shared registers map'}] is too short
	False schema does not allow 2
	1 was expected
	hint: "minItems" is only needed if less than the "items" list length
	from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml: ignoring, error in schema: allOf: 0: else: properties: reg
Documentation/devicetree/bindings/mfd/atmel,flexcom.example.dtb:0:0: /example-0/flexcom@f8034000: failed to match any schema with compatible: ['atmel,sama5d2-flexcom']
Documentation/devicetree/bindings/mfd/atmel,flexcom.example.dtb:0:0: /example-0/flexcom@f8034000/spi@400: failed to match any schema with compatible: ['atmel,at91rm9200-spi']
Documentation/devicetree/bindings/mfd/atmel,flexcom.example.dtb:0:0: /example-1/flexcom@e0064000: failed to match any schema with compatible: ['microchip,lan966x-flexcom']
Documentation/devicetree/bindings/mfd/atmel,flexcom.example.dtb:0:0: /example-1/flexcom@e0064000/spi@400: failed to match any schema with compatible: ['atmel,at91rm9200-spi']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.
Krzysztof Kozlowski June 17, 2022, 11:04 p.m. UTC | #2 
On 17/06/2022 06:07, Kavyasree Kotagiri wrote:
> LAN966x SoC flexcoms has two optional I/O lines. Namely, CS0 and CS1
> in flexcom SPI mode. CTS and RTS in flexcom USART mode. These pins
> can be mapped to lan966x FLEXCOM_SHARED[0-20] pins and usage depends on
> functions being configured.
> 
> Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
> ---
> v3 -> v4:
>  - Added else condition to allOf:if:then.
> 
> v2 -> v3:
>  - Add reg property of lan966x missed in v2.
> 
> v1 -> v2:
>  - Use allOf:if:then for lan966x dt properties
> 
>  .../bindings/mfd/atmel,flexcom.yaml           | 80 ++++++++++++++++++-
>  1 file changed, 79 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml b/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
> index fdb1645d123f..7e0e4d6b1b96 100644
> --- a/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
> +++ b/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
> @@ -18,9 +18,11 @@ properties:
>    compatible:
>      enum:
>        - atmel,sama5d2-flexcom
> +      - microchip,lan966x-flexcom


This looks good now.

>  
>    reg:
> -    maxItems: 1
> +    minItems: 1
> +    maxItems: 2
>  
>    clocks:
>      maxItems: 1
> @@ -47,6 +49,27 @@ properties:
>      $ref: /schemas/types.yaml#/definitions/uint32
>      enum: [1, 2, 3]
>  
> +  microchip,flx-shrd-pins:
> +    description: Specify the Flexcom shared pins to be used for flexcom
> +      chip-selects.
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      minimum: 0
> +      maximum: 20
> +
> +  microchip,flx-cs:
> +    description: Flexcom chip selects. Here, value of '0' represents "cts" line
> +      of flexcom USART or "cs0" line of flexcom SPI and value of '1' represents
> +      "rts" line of flexcom USART or "cs1" line of flexcom SPI.
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      minimum: 0
> +      maximum: 1
> +
>  patternProperties:
>    "^serial@[0-9a-f]+$":
>      description: See atmel-usart.txt for details of USART bindings.
> @@ -73,6 +96,33 @@ required:
>    - ranges
>    - atmel,flexcom-mode
>  
> +allOf:
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            const: microchip,lan966x-flexcom
> +
> +    then:
> +      properties:
> +        reg:
> +          minItems: 2
> +          items:
> +            - description: Flexcom base regsiters map

typo here - registers

> +            - description: Flexcom shared registers map
> +      required:
> +        - microchip,flx-shrd-pins
> +        - microchip,flx-cs
> +
> +    else:
> +      properties:
> +        reg:
> +          maxItems: 1

I think maxItems are not needed in such case. Rob's bot complains, so be
sure you test your bindings before sending.

> +          items:
> +            - description: Flexcom base regsiters map

typo

> +        microchip,flx-shrd-pins: false
> +        microchip,flx-cs: false
> +
>  additionalProperties: false
>  
>  examples:
> @@ -101,4 +151,32 @@ examples:
>                  atmel,fifo-size = <32>;
>            };
>      };
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    flx3: flexcom@e0064000 {
> +          compatible = "microchip,lan966x-flexcom";

Just like in patch #1 = wrong indentation. 4 spaces for the DTS example.

> +          reg = <0xe0064000 0x100>,
> +                <0xe2004180 0x8>;
> +          clocks = <&flx0_clk>;
> +          #address-cells = <1>;
> +          #size-cells = <1>;
> +          ranges = <0x0 0xe0040000 0x800>;
> +          atmel,flexcom-mode = <2>;
> +          microchip,flx-shrd-pins = <9>;
> +          microchip,flx-cs = <0>;
> +
> +          spi3: spi@400 {
> +                compatible = "atmel,at91rm9200-spi";
> +                reg = <0x400 0x200>;
> +                interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> +                pinctrl-names = "default";
> +                pinctrl-0 = <&pinctrl_flx3_default>;
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +                clocks = <&nic_clk>;
> +                clock-names = "spi_clk";
> +                atmel,fifo-size = <32>;
> +          };
> +    };
>  ...


Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml b/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
index fdb1645d123f..7e0e4d6b1b96 100644
--- a/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
+++ b/Documentation/devicetree/bindings/mfd/atmel,flexcom.yaml
@@ -18,9 +18,11 @@  properties:
   compatible:
     enum:
       - atmel,sama5d2-flexcom
+      - microchip,lan966x-flexcom
 
   reg:
-    maxItems: 1
+    minItems: 1
+    maxItems: 2
 
   clocks:
     maxItems: 1
@@ -47,6 +49,27 @@  properties:
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 2, 3]
 
+  microchip,flx-shrd-pins:
+    description: Specify the Flexcom shared pins to be used for flexcom
+      chip-selects.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 20
+
+  microchip,flx-cs:
+    description: Flexcom chip selects. Here, value of '0' represents "cts" line
+      of flexcom USART or "cs0" line of flexcom SPI and value of '1' represents
+      "rts" line of flexcom USART or "cs1" line of flexcom SPI.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 1
+
 patternProperties:
   "^serial@[0-9a-f]+$":
     description: See atmel-usart.txt for details of USART bindings.
@@ -73,6 +96,33 @@  required:
   - ranges
   - atmel,flexcom-mode
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: microchip,lan966x-flexcom
+
+    then:
+      properties:
+        reg:
+          minItems: 2
+          items:
+            - description: Flexcom base regsiters map
+            - description: Flexcom shared registers map
+      required:
+        - microchip,flx-shrd-pins
+        - microchip,flx-cs
+
+    else:
+      properties:
+        reg:
+          maxItems: 1
+          items:
+            - description: Flexcom base regsiters map
+        microchip,flx-shrd-pins: false
+        microchip,flx-cs: false
+
 additionalProperties: false
 
 examples:
@@ -101,4 +151,32 @@  examples:
                 atmel,fifo-size = <32>;
           };
     };
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    flx3: flexcom@e0064000 {
+          compatible = "microchip,lan966x-flexcom";
+          reg = <0xe0064000 0x100>,
+                <0xe2004180 0x8>;
+          clocks = <&flx0_clk>;
+          #address-cells = <1>;
+          #size-cells = <1>;
+          ranges = <0x0 0xe0040000 0x800>;
+          atmel,flexcom-mode = <2>;
+          microchip,flx-shrd-pins = <9>;
+          microchip,flx-cs = <0>;
+
+          spi3: spi@400 {
+                compatible = "atmel,at91rm9200-spi";
+                reg = <0x400 0x200>;
+                interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+                pinctrl-names = "default";
+                pinctrl-0 = <&pinctrl_flx3_default>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+                clocks = <&nic_clk>;
+                clock-names = "spi_clk";
+                atmel,fifo-size = <32>;
+          };
+    };
 ...