@@ -778,6 +778,8 @@ static int lan966x_probe_port(struct lan966x *lan966x, u32 p,
port->phylink_config.supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_QSGMII,
port->phylink_config.supported_interfaces);
+ __set_bit(PHY_INTERFACE_MODE_QUSGMII,
+ port->phylink_config.supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_1000BASEX,
port->phylink_config.supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_2500BASEX,
@@ -28,11 +28,12 @@ static int lan966x_phylink_mac_prepare(struct phylink_config *config,
phy_interface_t iface)
{
struct lan966x_port *port = netdev_priv(to_net_dev(config->dev));
+ phy_interface_t serdes_mode = iface;
int err;
if (port->serdes) {
err = phy_set_mode_ext(port->serdes, PHY_MODE_ETHERNET,
- iface);
+ serdes_mode);
if (err) {
netdev_err(to_net_dev(config->dev),
"Could not set mode of SerDes\n");
@@ -168,7 +168,7 @@ static void lan966x_port_link_up(struct lan966x_port *port)
/* Also the GIGA_MODE_ENA(1) needs to be set regardless of the
* port speed for QSGMII ports.
*/
- if (config->portmode == PHY_INTERFACE_MODE_QSGMII)
+ if (phy_interface_num_ports(config->portmode) == 4)
mode = DEV_MAC_MODE_CFG_GIGA_MODE_ENA_SET(1);
lan_wr(config->duplex | mode,
@@ -331,10 +331,14 @@ int lan966x_port_pcs_set(struct lan966x_port *port,
struct lan966x *lan966x = port->lan966x;
bool inband_aneg = false;
bool outband;
+ bool full_preamble = false;
+
+ if (config->portmode == PHY_INTERFACE_MODE_QUSGMII)
+ full_preamble = true;
if (config->inband) {
if (config->portmode == PHY_INTERFACE_MODE_SGMII ||
- config->portmode == PHY_INTERFACE_MODE_QSGMII)
+ phy_interface_num_ports(config->portmode) == 4)
inband_aneg = true; /* Cisco-SGMII in-band-aneg */
else if (config->portmode == PHY_INTERFACE_MODE_1000BASEX &&
config->autoneg)
@@ -345,9 +349,15 @@ int lan966x_port_pcs_set(struct lan966x_port *port,
outband = true;
}
- /* Disable or enable inband */
- lan_rmw(DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA_SET(outband),
- DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA,
+ /* Disable or enable inband.
+ * For QUSGMII, we rely on the preamble to transmit data such as
+ * timestamps, therefore force full preamble transmission, and prevent
+ * premable shortening
+ */
+ lan_rmw(DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA_SET(outband) |
+ DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA_SET(full_preamble),
+ DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA |
+ DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA,
lan966x, DEV_PCS1G_MODE_CFG(port->chip_port));
/* Enable PCS */
@@ -396,7 +406,7 @@ void lan966x_port_init(struct lan966x_port *port)
if (lan966x->fdma)
lan966x_fdma_netdev_init(lan966x, port->dev);
- if (config->portmode != PHY_INTERFACE_MODE_QSGMII)
+ if (phy_interface_num_ports(config->portmode) != 4)
return;
lan_rmw(DEV_CLOCK_CFG_PCS_RX_RST_SET(0) |
@@ -504,6 +504,12 @@ enum lan966x_target {
#define DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA_GET(x)\
FIELD_GET(DEV_PCS1G_MODE_CFG_SGMII_MODE_ENA, x)
+#define DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA BIT(1)
+#define DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA_SET(x)\
+ FIELD_PREP(DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA, x)
+#define DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA_GET(x)\
+ FIELD_GET(DEV_PCS1G_MODE_CFG_SAVE_PREAMBLE_ENA, x)
+
/* DEV:PCS1G_CFG_STATUS:PCS1G_SD_CFG */
#define DEV_PCS1G_SD_CFG(t) __REG(TARGET_DEV, t, 8, 72, 0, 1, 68, 8, 0, 1, 4)
The Lan996x controller supports the QUSGMII mode, which is very similar to QSGMII in the way it's configured and the autonegociation capababilities it provides. This commit adds support for that mode, treating it most of the time like QSGMII, making sure that we do configure the PCS how we should. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> --- V1->V2 : Pass the QUSGMII mode as-is to the generic PHY driver, and use phy_interface_num_ports, as per Russell's review V2->V3 : No changes .../ethernet/microchip/lan966x/lan966x_main.c | 2 ++ .../microchip/lan966x/lan966x_phylink.c | 3 ++- .../ethernet/microchip/lan966x/lan966x_port.c | 22 ++++++++++++++----- .../ethernet/microchip/lan966x/lan966x_regs.h | 6 +++++ 4 files changed, 26 insertions(+), 7 deletions(-)