deleted file mode 100644
@@ -1,113 +0,0 @@
-* Altera Triple-Speed Ethernet MAC driver (TSE)
-
-Required properties:
-- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should
- be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE.
- ALTR is supported for legacy device trees, but is deprecated.
- altr should be used for all new designs.
-- reg: Address and length of the register set for the device. It contains
- the information of registers in the same order as described by reg-names
-- reg-names: Should contain the reg names
- "control_port": MAC configuration space region
- "tx_csr": xDMA Tx dispatcher control and status space region
- "tx_desc": MSGDMA Tx dispatcher descriptor space region
- "rx_csr" : xDMA Rx dispatcher control and status space region
- "rx_desc": MSGDMA Rx dispatcher descriptor space region
- "rx_resp": MSGDMA Rx dispatcher response space region
- "s1": SGDMA descriptor memory
-- interrupts: Should contain the TSE interrupts and its mode.
-- interrupt-names: Should contain the interrupt names
- "rx_irq": xDMA Rx dispatcher interrupt
- "tx_irq": xDMA Tx dispatcher interrupt
-- rx-fifo-depth: MAC receive FIFO buffer depth in bytes
-- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes
-- phy-mode: See ethernet.txt in the same directory.
-- phy-handle: See ethernet.txt in the same directory.
-- phy-addr: See ethernet.txt in the same directory. A configuration should
- include phy-handle or phy-addr.
-- altr,has-supplementary-unicast:
- If present, TSE supports additional unicast addresses.
- Otherwise additional unicast addresses are not supported.
-- altr,has-hash-multicast-filter:
- If present, TSE supports a hash based multicast filter.
- Otherwise, hash-based multicast filtering is not supported.
-
-- mdio device tree subnode: When the TSE has a phy connected to its local
- mdio, there must be device tree subnode with the following
- required properties:
-
- - compatible: Must be "altr,tse-mdio".
- - #address-cells: Must be <1>.
- - #size-cells: Must be <0>.
-
- For each phy on the mdio bus, there must be a node with the following
- fields:
-
- - reg: phy id used to communicate to phy.
- - device_type: Must be "ethernet-phy".
-
-The MAC address will be determined using the optional properties defined in
-ethernet.txt.
-
-Example:
-
- tse_sub_0_eth_tse_0: ethernet@1,00000000 {
- compatible = "altr,tse-msgdma-1.0";
- reg = <0x00000001 0x00000000 0x00000400>,
- <0x00000001 0x00000460 0x00000020>,
- <0x00000001 0x00000480 0x00000020>,
- <0x00000001 0x000004A0 0x00000008>,
- <0x00000001 0x00000400 0x00000020>,
- <0x00000001 0x00000420 0x00000020>;
- reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
- interrupt-parent = <&hps_0_arm_gic_0>;
- interrupts = <0 41 4>, <0 40 4>;
- interrupt-names = "rx_irq", "tx_irq";
- rx-fifo-depth = <2048>;
- tx-fifo-depth = <2048>;
- address-bits = <48>;
- max-frame-size = <1500>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- phy-mode = "gmii";
- altr,has-supplementary-unicast;
- altr,has-hash-multicast-filter;
- phy-handle = <&phy0>;
- mdio {
- compatible = "altr,tse-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- phy0: ethernet-phy@0 {
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
-
- phy1: ethernet-phy@1 {
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
-
- };
- };
-
- tse_sub_1_eth_tse_0: ethernet@1,00001000 {
- compatible = "altr,tse-msgdma-1.0";
- reg = <0x00000001 0x00001000 0x00000400>,
- <0x00000001 0x00001460 0x00000020>,
- <0x00000001 0x00001480 0x00000020>,
- <0x00000001 0x000014A0 0x00000008>,
- <0x00000001 0x00001400 0x00000020>,
- <0x00000001 0x00001420 0x00000020>;
- reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
- interrupt-parent = <&hps_0_arm_gic_0>;
- interrupts = <0 43 4>, <0 42 4>;
- interrupt-names = "rx_irq", "tx_irq";
- rx-fifo-depth = <2048>;
- tx-fifo-depth = <2048>;
- address-bits = <48>;
- max-frame-size = <1500>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- phy-mode = "gmii";
- altr,has-supplementary-unicast;
- altr,has-hash-multicast-filter;
- phy-handle = <&phy1>;
- };
new file mode 100644
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/altr,tse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Altera Triple Speed Ethernet MAC driver (TSE)
+
+maintainers:
+ - Maxime Chevallier <maxime.chevallier@bootlin.com>
+
+allOf:
+ - $ref: "ethernet-controller.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - altr,tse-1.0
+ - ALTR,tse-1.0
+ then:
+ properties:
+ reg:
+ maxItems: 4
+ reg-names:
+ maxItems: 4
+ items:
+ - const: control_port
+ - const: rx_csr
+ - const: tx_csr
+ - const: s1
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - altr,tse-msgdma-1.0
+ then:
+ properties:
+ reg:
+ minItems: 6
+ reg-names:
+ minItems: 6
+ items:
+ - const: control_port
+ - const: rx_csr
+ - const: rx_desc
+ - const: rx_resp
+ - const: tx_csr
+ - const: tx_desc
+
+properties:
+ compatible:
+ enum:
+ - altr,tse-1.0
+ - ALTR,tse-1.0
+ - altr,tse-msgdma-1.0
+
+ interrupts:
+ minItems: 2
+
+ interrupt-names:
+ items:
+ - const: rx_irq
+ - const: tx_irq
+
+ rx-fifo-depth:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Depth in bytes of the RX FIFO
+
+ tx-fifo-depth:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Depth in bytes of the TX FIFO
+
+ altr,has_supplementary_unicast:
+ type: boolean
+ description:
+ If present, TSE supports additional unicast addresses.
+
+ altr,has_hash_multicast_filter:
+ type: boolean
+ description:
+ If present, TSE supports hash based multicast filter.
+
+ mdio:
+ $ref: mdio.yaml#
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - rx-fifo-depth
+ - tx-fifo-depth
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ tse_sub_1_eth_tse_0: ethernet@1,00001000 {
+ compatible = "altr,tse-msgdma-1.0";
+ reg = <0x00001000 0x00000400>,
+ <0x00001460 0x00000020>,
+ <0x00001480 0x00000020>,
+ <0x000014A0 0x00000008>,
+ <0x00001400 0x00000020>,
+ <0x00001420 0x00000020>;
+ reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
+ interrupt-parent = <&hps_0_arm_gic_0>;
+ interrupts = <0 43 4>, <0 42 4>;
+ interrupt-names = "rx_irq", "tx_irq";
+ rx-fifo-depth = <2048>;
+ tx-fifo-depth = <2048>;
+ address-bits = <48>;
+ max-frame-size = <1500>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ phy-mode = "gmii";
+ altr,has-supplementary-unicast;
+ altr,has-hash-multicast-filter;
+ phy-handle = <&phy1>;
+ mdio {
+ compatible = "altr,tse-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ };
+ };
+
+...
This converts the bindings for the Altera Triple-Speed Ethernet to yaml. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> --- .../devicetree/bindings/net/altera_tse.txt | 113 --------------- .../devicetree/bindings/net/altr,tse.yaml | 134 ++++++++++++++++++ 2 files changed, 134 insertions(+), 113 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/altera_tse.txt create mode 100644 Documentation/devicetree/bindings/net/altr,tse.yaml