@@ -2,35 +2,60 @@
//
// Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
+/ {
+ touchscreen {
+ compatible = "resistive-adc-touch";
+ io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>;
+ io-channel-names = "y", "z1", "z2", "x";
+ touchscreen-min-pressure = <65000>;
+ touchscreen-inverted-y;
+ touchscreen-swapped-x-y;
+ touchscreen-x-plate-ohms = <300>;
+ touchscreen-y-plate-ohms = <800>;
+ };
+};
+
&ecspi4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi4>;
cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
status = "okay";
- touchscreen@0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_touch>;
- compatible = "ti,tsc2046";
+ adc_ts: adc@0 {
+ compatible = "ti,tsc2046e-adc";
reg = <0>;
+ pinctrl-0 = <&pinctrl_touch>;
+ pinctrl-names ="default";
spi-max-frequency = <1000000>;
interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
- vcc-supply = <®_3v3>;
- pendown-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
- ti,x-plate-ohms = /bits/ 16 <850>;
- ti,y-plate-ohms = /bits/ 16 <295>;
- ti,pressure-min = /bits/ 16 <2>;
- ti,pressure-max = /bits/ 16 <1500>;
- ti,vref-mv = /bits/ 16 <3300>;
- ti,settle-delay-usec = /bits/ 16 <15>;
- ti,vref-delay-usecs = /bits/ 16 <0>;
- ti,penirq-recheck-delay-usecs = /bits/ 16 <100>;
- ti,debounce-max = /bits/ 16 <100>;
- ti,debounce-tol = /bits/ 16 <(~0)>;
- ti,debounce-rep = /bits/ 16 <4>;
- touchscreen-swapped-x-y;
- touchscreen-inverted-y;
- wakeup-source;
+ #io-channel-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@1 {
+ reg = <1>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@4 {
+ reg = <4>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ settling-time-us = <700>;
+ oversampling-ratio = <5>;
+ };
};
};
Start to use more generic resistive-adc-touch node. ti,tsc2046 is an ADC controller used for resistive touchscreen. So, define it as ADC and attach resistive-adc-touch to it. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi | 65 ++++++++++++++------ 1 file changed, 45 insertions(+), 20 deletions(-)