@@ -1,4 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-clockworkpi-v3.14.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-devterm-v3.14.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-dongshan-nezha-stu.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
new file mode 100644
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+ model = "ClockworkPi v3.14 (R-01)";
+ compatible = "clockwork,r-01-clockworkpi-v3.14", "allwinner,sun20i-d1";
+
+ aliases {
+ ethernet0 = &ap6256;
+ mmc0 = &mmc0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /*
+ * This regulator is PWM-controlled, but the PWM controller is not
+ * yet supported, so fix the regulator to its default voltage.
+ */
+ reg_vdd_cpu: vdd-cpu {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-cpu";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <®_vcc>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 11 GPIO_ACTIVE_LOW>; /* PG11/GPIO3 */
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpu>;
+};
+
+&dcxo {
+ clock-frequency = <24000000>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-0 = <&i2c0_pb10_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ axp221: pmic@34 {
+ compatible = "x-powers,axp228", "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&pio>;
+ interrupts = <4 9 IRQ_TYPE_LEVEL_LOW>; /* PE9/GPIO2 */
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ ac_power_supply: ac-power {
+ compatible = "x-powers,axp221-ac-power-supply";
+ };
+
+ axp_adc: adc {
+ compatible = "x-powers,axp221-adc";
+ #io-channel-cells = <1>;
+ };
+
+ battery_power_supply: battery-power {
+ compatible = "x-powers,axp221-battery-power-supply";
+ };
+
+ axp_gpio: gpio {
+ compatible = "x-powers,axp221-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ regulators {
+ x-powers,dcdc-freq = <3000>;
+
+ reg_dcdc1: dcdc1 {
+ regulator-name = "sys-3v3";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-name = "sys-1v8";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_aldo1: aldo1 {
+ regulator-name = "aud-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-name = "disp-3v3";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-name = "vdd-wifi";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* DLDO1 and ELDO1-3 are connected in parallel. */
+ reg_dldo1: dldo1 {
+ regulator-name = "vbat-wifi-a";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ /* DLDO2-DLDO4 are connected in parallel. */
+ reg_dldo2: dldo2 {
+ regulator-name = "vcc-3v3-ext-a";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_dldo3: dldo3 {
+ regulator-name = "vcc-3v3-ext-b";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_dldo4: dldo4 {
+ regulator-name = "vcc-3v3-ext-c";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-name = "vbat-wifi-b";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-name = "vbat-wifi-c";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-name = "vbat-wifi-d";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+
+ usb_power_supply: usb-power {
+ compatible = "x-powers,axp221-usb-power-supply";
+ status = "disabled";
+ };
+ };
+};
+
+&mmc0 {
+ broken-cd;
+ bus-width = <4>;
+ disable-wp;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_vcc_3v3>;
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mmc1 {
+ bus-width = <4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_aldo3>;
+ pinctrl-0 = <&mmc1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ ap6256: wifi@1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10/GPIO4 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pg-supply = <®_ldoa>;
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pb8_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ uart-has-rtscts;
+ pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ interrupt-parent = <&pio>;
+ interrupts = <6 17 IRQ_TYPE_LEVEL_HIGH>; /* PG17/GPIO6 */
+ device-wakeup-gpios = <&pio 6 16 GPIO_ACTIVE_HIGH>; /* PG16/GPIO7 */
+ shutdown-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18/GPIO5 */
+ max-speed = <1500000>;
+ vbat-supply = <®_dldo1>;
+ vddio-supply = <®_aldo3>;
+ };
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus_power-supply = <&ac_power_supply>;
+ usb1_vbus-supply = <®_vcc>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include "sun20i-d1-clockworkpi-v3.14.dts"
+
+/ {
+ model = "Clockwork DevTerm (R-01)";
+ compatible = "clockwork,r-01-devterm-v3.14",
+ "clockwork,r-01-clockworkpi-v3.14",
+ "allwinner,sun20i-d1";
+
+ fan {
+ compatible = "gpio-fan";
+ gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10/GPIO41 */
+ gpio-fan,speed-map = <0 0>,
+ <6000 1>;
+ #cooling-cells = <2>;
+ };
+
+ i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 3 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PD14/GPIO44 */
+ scl-gpios = <&pio 3 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PD15/GPIO45 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@54 {
+ compatible = "ti,adc101c";
+ reg = <0x54>;
+ interrupt-parent = <&pio>;
+ interrupts = <4 12 IRQ_TYPE_LEVEL_LOW>; /* PE12/GPIO35 */
+ vref-supply = <®_dldo2>;
+ #io-channel-cells = <1>;
+ };
+ };
+};
Clockwork Tech manufactures several SoMs for their RasPi CM3-compatible "ClockworkPi" mainboard. Their R-01 SoM features the Allwinner D1 SoC. The R-01 contains only the CPU, DRAM, and always-on voltage regulation; it does not merit a separate devicetree. The ClockworkPi mainboard features analog audio, a MIPI-DSI panel, USB host and peripheral ports, an Ampak AP6256 WiFi/Bluetooth module, and an X-Powers AXP228 PMIC for managing a Li-ion battery. The DevTerm is a complete system which extends the ClockworkPi mainboard with a MIPI-DSI panel and a pair of expansion boards. These expansion boards provide a fan, a USB keyboard, speakers, and a thermal printer. Signed-off-by: Samuel Holland <samuel@sholland.org> --- Changes in v2: - Added PMIC GPIO controller node (binding merged for 6.2) arch/riscv/boot/dts/allwinner/Makefile | 2 + .../allwinner/sun20i-d1-clockworkpi-v3.14.dts | 253 ++++++++++++++++++ .../dts/allwinner/sun20i-d1-devterm-v3.14.dts | 36 +++ 3 files changed, 291 insertions(+) create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-clockworkpi-v3.14.dts create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-devterm-v3.14.dts