diff mbox series

[v2,08/12] riscv: dts: allwinner: Add MangoPi MQ Pro devicetree

Message ID 20221125234656.47306-9-samuel@sholland.org (mailing list archive)
State New, archived
Headers show
Series riscv: Allwinner D1/D1s platform support | expand

Commit Message

Samuel Holland Nov. 25, 2022, 11:46 p.m. UTC 
The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.

The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.

Signed-off-by: Samuel Holland <samuel@sholland.org>
---

Changes in v2:
 - Added LED (GPIO shared between onboard LED and backlight regulator)

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun20i-d1-mangopi-mq-pro.dts    | 143 ++++++++++++++++++
 2 files changed, 144 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts

Comments

Guo Ren Nov. 26, 2022, 12:25 a.m. UTC | #1 
Reviewed-by: Guo Ren <guoren@kernel.org>

On Sat, Nov 26, 2022 at 7:47 AM Samuel Holland <samuel@sholland.org> wrote:
>
> The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
> Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
> and an RTL8723DS-based WiFi/Bluetooth module.
>
> The board also exposes GPIO Port E via a connector on the end of the
> board, which can support either a camera or an RMII Ethernet PHY. The
> additional regulators supply that connector.
>
> Signed-off-by: Samuel Holland <samuel@sholland.org>
> ---
>
> Changes in v2:
>  - Added LED (GPIO shared between onboard LED and backlight regulator)
>
>  arch/riscv/boot/dts/allwinner/Makefile        |   1 +
>  .../allwinner/sun20i-d1-mangopi-mq-pro.dts    | 143 ++++++++++++++++++
>  2 files changed, 144 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
>
> diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
> index f1c70b9dc9bf..2ed586fafaea 100644
> --- a/arch/riscv/boot/dts/allwinner/Makefile
> +++ b/arch/riscv/boot/dts/allwinner/Makefile
> @@ -3,5 +3,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
> diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
> new file mode 100644
> index 000000000000..6d5897dc22e2
> --- /dev/null
> +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
> @@ -0,0 +1,143 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/dts-v1/;
> +
> +#include "sun20i-d1.dtsi"
> +#include "sun20i-common-regulators.dtsi"
> +
> +/ {
> +       model = "MangoPi MQ Pro";
> +       compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
> +
> +       aliases {
> +               ethernet0 = &rtl8723ds;
> +               mmc0 = &mmc0;
> +               serial0 = &uart0;
> +       };
> +
> +       chosen {
> +               stdout-path = "serial0:115200n8";
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               led-0 {
> +                       color = <LED_COLOR_ID_BLUE>;
> +                       function = LED_FUNCTION_BACKLIGHT;
> +                       gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
> +               };
> +       };
> +
> +       reg_avdd2v8: avdd2v8 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "avdd2v8";
> +               regulator-min-microvolt = <2800000>;
> +               regulator-max-microvolt = <2800000>;
> +               vin-supply = <&reg_vcc_3v3>;
> +       };
> +
> +       reg_dvdd: dvdd {
> +               compatible = "regulator-fixed";
> +               regulator-name = "dvdd";
> +               regulator-min-microvolt = <1200000>;
> +               regulator-max-microvolt = <1200000>;
> +               vin-supply = <&reg_vcc_3v3>;
> +       };
> +
> +       reg_vdd_cpu: vdd-cpu {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vdd-cpu";
> +               regulator-min-microvolt = <1100000>;
> +               regulator-max-microvolt = <1100000>;
> +               vin-supply = <&reg_vcc>;
> +       };
> +
> +       wifi_pwrseq: wifi-pwrseq {
> +               compatible = "mmc-pwrseq-simple";
> +               reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
> +       };
> +};
> +
> +&cpu0 {
> +       cpu-supply = <&reg_vdd_cpu>;
> +};
> +
> +&dcxo {
> +       clock-frequency = <24000000>;
> +};
> +
> +&ehci1 {
> +       status = "okay";
> +};
> +
> +&mmc0 {
> +       bus-width = <4>;
> +       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> +       disable-wp;
> +       vmmc-supply = <&reg_vcc_3v3>;
> +       vqmmc-supply = <&reg_vcc_3v3>;
> +       pinctrl-0 = <&mmc0_pins>;
> +       pinctrl-names = "default";
> +       status = "okay";
> +};
> +
> +&mmc1 {
> +       bus-width = <4>;
> +       mmc-pwrseq = <&wifi_pwrseq>;
> +       non-removable;
> +       vmmc-supply = <&reg_vcc_3v3>;
> +       vqmmc-supply = <&reg_vcc_3v3>;
> +       pinctrl-0 = <&mmc1_pins>;
> +       pinctrl-names = "default";
> +       status = "okay";
> +
> +       rtl8723ds: wifi@1 {
> +               reg = <1>;
> +               interrupt-parent = <&pio>;
> +               interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
> +               interrupt-names = "host-wake";
> +       };
> +};
> +
> +&ohci1 {
> +       status = "okay";
> +};
> +
> +&pio {
> +       vcc-pe-supply = <&reg_avdd2v8>;
> +};
> +
> +&uart0 {
> +       pinctrl-0 = <&uart0_pb8_pins>;
> +       pinctrl-names = "default";
> +       status = "okay";
> +};
> +
> +&uart1 {
> +       uart-has-rtscts;
> +       pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
> +       pinctrl-names = "default";
> +       status = "okay";
> +
> +       bluetooth {
> +               compatible = "realtek,rtl8723ds-bt";
> +               device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
> +               enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
> +               host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
> +       };
> +};
> +
> +&usb_otg {
> +       dr_mode = "peripheral";
> +       status = "okay";
> +};
> +
> +&usbphy {
> +       usb1_vbus-supply = <&reg_vcc>;
> +       status = "okay";
> +};
> --
> 2.37.4
>
Jernej Škrabec Dec. 5, 2022, 8:42 p.m. UTC | #2 
Dne sobota, 26. november 2022 ob 00:46:52 CET je Samuel Holland napisal(a):
> The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
> Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
> and an RTL8723DS-based WiFi/Bluetooth module.
> 
> The board also exposes GPIO Port E via a connector on the end of the
> board, which can support either a camera or an RMII Ethernet PHY. The
> additional regulators supply that connector.
> 
> Signed-off-by: Samuel Holland <samuel@sholland.org>

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Best regards,
Jernej
diff mbox series

Patch

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index f1c70b9dc9bf..2ed586fafaea 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -3,5 +3,6 @@  dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
new file mode 100644
index 000000000000..6d5897dc22e2
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
@@ -0,0 +1,143 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ Pro";
+	compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &rtl8723ds;
+		mmc0 = &mmc0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_BACKLIGHT;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
+		host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};