| Message ID | 20221229042230.24532-1-samuel@sholland.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | clk: sunxi-ng: h3/h5: Model H3 CLK_DRAM as a fixed clock | expand |
在 2022-12-28星期三的 22:22 -0600，Samuel Holland写道： > The DRAM controller clock is only allowed to change frequency while > the > DRAM chips are in self-refresh. To support this, changes to the > CLK_DRAM > mux and divider have no effect until acknowledged by the memory > dynamic > frequency scaling (MDFS) hardware inside the DRAM controller. (There > is > a SDRCLK_UPD bit in DRAM_CFG_REG which should serve a similar > purpose, > but this bit actually does nothing.) > > However, the MDFS hardware in H3 appears to be broken. Triggering a > frequency change using the procedure from similar SoCs (A64/H5) hangs > the hardware. Additionally, the vendor BSP specifically avoids using > the > MDFS hardware on H3, instead performing all DRAM PHY parameter > updates > and resets in software. > > Thus, it is effectively impossible to change the CLK_DRAM > mux/divider, > so those features should not be modeled. Add CLK_SET_RATE_PARENT so > frequency changes apply to PLL_DDR instead. > > Signed-off-by: Samuel Holland <samuel@sholland.org> > --- > > drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 15 ++++++++++----- > 1 file changed, 10 insertions(+), 5 deletions(-) > > diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi- > ng/ccu-sun8i-h3.c > index d3fcb983c17c..bfebe8dbbe65 100644 > --- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c > +++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c > @@ -434,8 +434,13 @@ static SUNXI_CCU_GATE(usb_ohci2_clk, "usb- > ohci2", "osc24M", > static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc24M", > 0x0cc, BIT(19), 0); > > -static const char * const dram_parents[] = { "pll-ddr", "pll- > periph0-2x" }; > -static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents, > +/* H3 has broken MDFS hardware, so the mux/divider cannot be > changed. */ > +static CLK_FIXED_FACTOR_HW(h3_dram_clk, "dram", > + &pll_ddr_clk.common.hw, > + 1, 1, CLK_SET_RATE_PARENT | > CLK_IS_CRITICAL); Should we do some sanity check on the values when probing CCU? > + > +static const char * const h5_dram_parents[] = { "pll-ddr", "pll- > periph0-2x" }; > +static SUNXI_CCU_M_WITH_MUX(h5_dram_clk, "dram", h5_dram_parents, > 0x0f4, 0, 4, 20, 2, CLK_IS_CRITICAL); > > static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram", > @@ -592,7 +597,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = { > &usb_ohci1_clk.common, > &usb_ohci2_clk.common, > &usb_ohci3_clk.common, > - &dram_clk.common, > + &h5_dram_clk.common, > &dram_ve_clk.common, > &dram_csi_clk.common, > &dram_deinterlace_clk.common, > @@ -732,7 +737,7 @@ static struct clk_hw_onecell_data > sun8i_h3_hw_clks = { > [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, > [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw, > [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw, > - [CLK_DRAM] = &dram_clk.common.hw, > + [CLK_DRAM] = &h3_dram_clk.hw, > [CLK_DRAM_VE] = &dram_ve_clk.common.hw, > [CLK_DRAM_CSI] = &dram_csi_clk.common.hw, > [CLK_DRAM_DEINTERLACE] = > &dram_deinterlace_clk.common.hw, > @@ -848,7 +853,7 @@ static struct clk_hw_onecell_data > sun50i_h5_hw_clks = { > [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, > [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw, > [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw, > - [CLK_DRAM] = &dram_clk.common.hw, > + [CLK_DRAM] = &h5_dram_clk.common.hw, > [CLK_DRAM_VE] = &dram_ve_clk.common.hw, > [CLK_DRAM_CSI] = &dram_csi_clk.common.hw, > [CLK_DRAM_DEINTERLACE] = > &dram_deinterlace_clk.common.hw,
On 12/28/22 23:22, Icenowy Zheng wrote: > 在 2022-12-28星期三的 22:22 -0600，Samuel Holland写道： >> The DRAM controller clock is only allowed to change frequency while >> the >> DRAM chips are in self-refresh. To support this, changes to the >> CLK_DRAM >> mux and divider have no effect until acknowledged by the memory >> dynamic >> frequency scaling (MDFS) hardware inside the DRAM controller. (There >> is >> a SDRCLK_UPD bit in DRAM_CFG_REG which should serve a similar >> purpose, >> but this bit actually does nothing.) >> >> However, the MDFS hardware in H3 appears to be broken. Triggering a >> frequency change using the procedure from similar SoCs (A64/H5) hangs >> the hardware. Additionally, the vendor BSP specifically avoids using >> the >> MDFS hardware on H3, instead performing all DRAM PHY parameter >> updates >> and resets in software. >> >> Thus, it is effectively impossible to change the CLK_DRAM >> mux/divider, >> so those features should not be modeled. Add CLK_SET_RATE_PARENT so >> frequency changes apply to PLL_DDR instead. >> >> Signed-off-by: Samuel Holland <samuel@sholland.org> >> --- >> >> drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 15 ++++++++++----- >> 1 file changed, 10 insertions(+), 5 deletions(-) >> >> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi- >> ng/ccu-sun8i-h3.c >> index d3fcb983c17c..bfebe8dbbe65 100644 >> --- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c >> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c >> @@ -434,8 +434,13 @@ static SUNXI_CCU_GATE(usb_ohci2_clk, "usb- >> ohci2", "osc24M", >> static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc24M", >> 0x0cc, BIT(19), 0); >> >> -static const char * const dram_parents[] = { "pll-ddr", "pll- >> periph0-2x" }; >> -static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents, >> +/* H3 has broken MDFS hardware, so the mux/divider cannot be >> changed. */ >> +static CLK_FIXED_FACTOR_HW(h3_dram_clk, "dram", >> + &pll_ddr_clk.common.hw, >> + 1, 1, CLK_SET_RATE_PARENT | >> CLK_IS_CRITICAL); > > Should we do some sanity check on the values when probing CCU? It is not necessary, because the register value is ignored. The register is interpreted as if it contains 0x80000000, regardless of what you write to it. So the parent/divider listed here will always be correct. Regards, Samuel
Dne četrtek, 29. december 2022 ob 05:22:30 CET je Samuel Holland napisal(a): > The DRAM controller clock is only allowed to change frequency while the > DRAM chips are in self-refresh. To support this, changes to the CLK_DRAM > mux and divider have no effect until acknowledged by the memory dynamic > frequency scaling (MDFS) hardware inside the DRAM controller. (There is > a SDRCLK_UPD bit in DRAM_CFG_REG which should serve a similar purpose, > but this bit actually does nothing.) > > However, the MDFS hardware in H3 appears to be broken. Triggering a > frequency change using the procedure from similar SoCs (A64/H5) hangs > the hardware. Additionally, the vendor BSP specifically avoids using the > MDFS hardware on H3, instead performing all DRAM PHY parameter updates > and resets in software. > > Thus, it is effectively impossible to change the CLK_DRAM mux/divider, > so those features should not be modeled. Add CLK_SET_RATE_PARENT so > frequency changes apply to PLL_DDR instead. > > Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Best regards, Jernej
Dne četrtek, 29. december 2022 ob 05:22:30 CET je Samuel Holland napisal(a): > The DRAM controller clock is only allowed to change frequency while the > DRAM chips are in self-refresh. To support this, changes to the CLK_DRAM > mux and divider have no effect until acknowledged by the memory dynamic > frequency scaling (MDFS) hardware inside the DRAM controller. (There is > a SDRCLK_UPD bit in DRAM_CFG_REG which should serve a similar purpose, > but this bit actually does nothing.) > > However, the MDFS hardware in H3 appears to be broken. Triggering a > frequency change using the procedure from similar SoCs (A64/H5) hangs > the hardware. Additionally, the vendor BSP specifically avoids using the > MDFS hardware on H3, instead performing all DRAM PHY parameter updates > and resets in software. > > Thus, it is effectively impossible to change the CLK_DRAM mux/divider, > so those features should not be modeled. Add CLK_SET_RATE_PARENT so > frequency changes apply to PLL_DDR instead. > > Signed-off-by: Samuel Holland <samuel@sholland.org> Applied, thanks! Best regards, Jernej
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c index d3fcb983c17c..bfebe8dbbe65 100644 --- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c +++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c @@ -434,8 +434,13 @@ static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc24M", static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc24M", 0x0cc, BIT(19), 0); -static const char * const dram_parents[] = { "pll-ddr", "pll-periph0-2x" }; -static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents, +/* H3 has broken MDFS hardware, so the mux/divider cannot be changed. */ +static CLK_FIXED_FACTOR_HW(h3_dram_clk, "dram", + &pll_ddr_clk.common.hw, + 1, 1, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL); + +static const char * const h5_dram_parents[] = { "pll-ddr", "pll-periph0-2x" }; +static SUNXI_CCU_M_WITH_MUX(h5_dram_clk, "dram", h5_dram_parents, 0x0f4, 0, 4, 20, 2, CLK_IS_CRITICAL); static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram", @@ -592,7 +597,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = { &usb_ohci1_clk.common, &usb_ohci2_clk.common, &usb_ohci3_clk.common, - &dram_clk.common, + &h5_dram_clk.common, &dram_ve_clk.common, &dram_csi_clk.common, &dram_deinterlace_clk.common, @@ -732,7 +737,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = { [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw, [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw, - [CLK_DRAM] = &dram_clk.common.hw, + [CLK_DRAM] = &h3_dram_clk.hw, [CLK_DRAM_VE] = &dram_ve_clk.common.hw, [CLK_DRAM_CSI] = &dram_csi_clk.common.hw, [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw, @@ -848,7 +853,7 @@ static struct clk_hw_onecell_data sun50i_h5_hw_clks = { [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw, [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw, [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw, - [CLK_DRAM] = &dram_clk.common.hw, + [CLK_DRAM] = &h5_dram_clk.common.hw, [CLK_DRAM_VE] = &dram_ve_clk.common.hw, [CLK_DRAM_CSI] = &dram_csi_clk.common.hw, [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
The DRAM controller clock is only allowed to change frequency while the DRAM chips are in self-refresh. To support this, changes to the CLK_DRAM mux and divider have no effect until acknowledged by the memory dynamic frequency scaling (MDFS) hardware inside the DRAM controller. (There is a SDRCLK_UPD bit in DRAM_CFG_REG which should serve a similar purpose, but this bit actually does nothing.) However, the MDFS hardware in H3 appears to be broken. Triggering a frequency change using the procedure from similar SoCs (A64/H5) hangs the hardware. Additionally, the vendor BSP specifically avoids using the MDFS hardware on H3, instead performing all DRAM PHY parameter updates and resets in software. Thus, it is effectively impossible to change the CLK_DRAM mux/divider, so those features should not be modeled. Add CLK_SET_RATE_PARENT so frequency changes apply to PLL_DDR instead. Signed-off-by: Samuel Holland <samuel@sholland.org> --- drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-)