diff mbox series

[v7,7/7] arm64: dts: mediatek: Initial mt8365-evk support

Message ID 20230101220149.3035048-8-bero@baylibre.com (mailing list archive)
State New, archived
Headers show
Series Add minimal MT8365 and MT8365-EVK support | expand

Commit Message

Bernhard Rosenkränzer Jan. 1, 2023, 10:01 p.m. UTC
From: Fabien Parent <fparent@baylibre.com>

This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
 arch/arm64/boot/dts/mediatek/Makefile       |   1 +
 arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
 arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 378 ++++++++++++++++++++
 3 files changed, 548 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi

Comments

Matthias Brugger Jan. 20, 2023, 10:57 a.m. UTC | #1
On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> From: Fabien Parent <fparent@baylibre.com>
> 
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
> 
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
>   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
>   arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
>   arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 378 ++++++++++++++++++++
>   3 files changed, 548 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96d..d78523c5a7dd6 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
>   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> new file mode 100644
> index 0000000000000..275ea3a0e7085
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
[...]
> +		apdma: dma-controller@11000280 {
> +			compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
> +			reg = <0 0x11000280 0 0x80>,
> +			      <0 0x11000300 0 0x80>,
> +			      <0 0x11000380 0 0x80>,
> +			      <0 0x11000400 0 0x80>,
> +			      <0 0x11000580 0 0x80>,
> +			      <0 0x11000600 0 0x80>;
> +			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
> +			dma-requests = <6>;
> +			clocks = <&infracfg CLK_IFR_AP_DMA>;
> +			clock-names = "apdma";
> +			#dma-cells = <1>;
> +		};
> +
> +		uart0: serial@11002000 {
> +			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";

Unfortunately we are missing this compatible in the binding description.

> +			reg = <0 0x11002000 0 0x1000>;
> +			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 0>, <&apdma 1>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@11003000 {
> +			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> +			reg = <0 0x11003000 0 0x1000>;
> +			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 2>, <&apdma 3>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@11004000 {
> +			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> +			reg = <0 0x11004000 0 0x1000>;
> +			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
> +			clock-names = "baud", "bus";
> +			dmas = <&apdma 4>, <&apdma 5>;
> +			dma-names = "tx", "rx";
> +			status = "disabled";
> +		};
> +
> +		pwm: pwm@11006000 {
> +			compatible = "mediatek,mt8365-pwm";
> +			reg = <0 0x11006000 0 0x1000>;
> +			#pwm-cells = <2>;
> +			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&infracfg CLK_IFR_PWM_HCLK>,
> +				 <&infracfg CLK_IFR_PWM>,
> +				 <&infracfg CLK_IFR_PWM1>,
> +				 <&infracfg CLK_IFR_PWM2>,
> +				 <&infracfg CLK_IFR_PWM3>;
> +			clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
> +		};
> +
> +		spi: spi@1100a000 {
> +			compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
> +			reg = <0 0x1100a000 0 0x100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> +				 <&topckgen CLK_TOP_SPI_SEL>,
> +				 <&infracfg CLK_IFR_SPI0>;
> +			clock-names = "parent-clk", "sel-clk", "spi-clk";
> +			status = "disabled";
> +		};
> +
> +		ssusb: usb@11201000 {
> +			compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";

Same here.

> +			reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
> +			reg-names = "mac", "ippc";
> +			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
> +			phys = <&u2port0 PHY_TYPE_USB2>,
> +			       <&u2port1 PHY_TYPE_USB2>;
> +			clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> +				 <&infracfg CLK_IFR_SSUSB_REF>,
> +				 <&infracfg CLK_IFR_SSUSB_SYS>,
> +				 <&infracfg CLK_IFR_ICUSB>;
> +			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			status = "disabled";
> +
> +			usb_host: usb@11200000 {
> +				compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";

Same here.

> +				reg = <0 0x11200000 0 0x1000>;
> +				reg-names = "mac";
> +				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
> +				clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> +					 <&infracfg CLK_IFR_SSUSB_REF>,
> +					 <&infracfg CLK_IFR_SSUSB_SYS>,
> +					 <&infracfg CLK_IFR_ICUSB>,
> +					 <&infracfg CLK_IFR_SSUSB_XHCI>;
> +				clock-names = "sys_ck", "ref_ck", "mcu_ck",
> +					      "dma_ck", "xhci_ck";
> +				status = "disabled";
> +			};
> +		};
> +
> +		u3phy: phy@11cc0000 {
> +			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			#phy-cells = <1>;
> +			ranges;
> +
> +			u2port0: usb-phy@11cc0000 {
> +				reg = <0 0x11cc0000 0 0x400>;
> +				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> +					 <&topckgen CLK_TOP_USB20_48M_EN>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u2port1: usb-phy@11cc1000 {
> +				reg = <0 0x11cc1000 0 0x400>;
> +				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> +					 <&topckgen CLK_TOP_USB20_48M_EN>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	system_clk: dummy13m {
> +		compatible = "fixed-clock";
> +		clock-frequency = <13000000>;
> +		#clock-cells = <0>;
> +	};
> +
> +	systimer: timer@10017000 {
> +		compatible = "mediatek,mt6795-systimer";

Why don't we use a compatible like
"mediatek,mt8365-systimer", "mediatek,mt6795-systimer";

We would need to add this to the binding description as well.

I leave it up to you, but I'd advise to start with a minimal working DT which 
includes only the bindings that are already merged. Then we can take the new 
devices like mtu3, xhci, spidev or i2c later once they are ready.

Regards,
Matthias
Bernhard Rosenkränzer Jan. 23, 2023, 4:10 p.m. UTC | #2
Hi,

On Fri, Jan 20, 2023 at 11:57 AM Matthias Brugger
<matthias.bgg@gmail.com> wrote:
> On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> > +             uart0: serial@11002000 {
> > +                     compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
>
> Unfortunately we are missing this compatible in the binding description.

True, overlooked that one.

> > +             ssusb: usb@11201000 {
> > +                     compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
>
> Same here.

This is actually added by an earlier patch within this series (5/7),
but since it isn't used anywhere yet, might as well drop it for now,
"mediatek,mtu3" by itself works.

> > +                     usb_host: usb@11200000 {
> > +                             compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
>
> Same here.

Also added by an earlier patch within the series (6/7), and also not
used anywhere yet.

> > +     systimer: timer@10017000 {
> > +             compatible = "mediatek,mt6795-systimer";
>
> Why don't we use a compatible like
> "mediatek,mt8365-systimer", "mediatek,mt6795-systimer";

That was in an earlier revision and removed (because the binding
description wasn't merged yet). Can add it of course (but then
mediatek,mt8365-uart and friends should probably stay as well).

I'll post a new revision adding it back (along with the binding
description) and add the binding description for mt8365-uart as well
(getting it to the same place mediatek,mt8365-mtu3 and
mediatek,mt8365-xhci are now).
Let me know if you'd prefer a variant that drops mediatek,mt8365-uart,
mediatek,mt8365-mtu3, mediatek,mt8365-xhci and doesn't bring back
mediatek,mt8365-systimer -- either one works for me, the fallbacks are
sufficient to make it work.

ttyl
bero
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+	model = "MediaTek MT8365 Open Platform EVK";
+	compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-volume-up {
+			gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0xc0000000>;
+	};
+
+	usb_otg_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@43000000 {
+			no-map;
+			reg = <0 0x43000000 0 0x20000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&pio {
+	gpio_keys: gpio-keys-pins {
+		pins {
+			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+			bias-pull-up;
+			input-enable;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+				 <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+				 <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		pins {
+			pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+				 <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+		};
+	};
+
+	usb_pins: usb-pins {
+		pins-id {
+			pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-usb0-vbus {
+			pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+			output-high;
+		};
+
+		pin-usb1-vbus {
+			pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+			output-high;
+		};
+	};
+
+	pwm_pins: pwm-pins {
+		pins {
+			pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+				 <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..a32f2b7507be3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,378 @@ 
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "mediatek,mt8365";
+	interrupt-parent = <&sysirq>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+		};
+	};
+
+	clk26m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x10000>, /* GICD */
+			      <0 0x0c080000 0 0x80000>, /* GICR */
+			      <0 0x0c400000 0 0x2000>,  /* GICC */
+			      <0 0x0c410000 0 0x1000>,  /* GICH */
+			      <0 0x0c420000 0 0x2000>;  /* GICV */
+
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8365-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg: syscon@10001000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8365-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		syscfg_pctl: syscfg-pctl@10005000 {
+			compatible = "mediatek,mt8365-syscfg", "syscon";
+			reg = <0 0x10005000 0 0x1000>;
+		};
+
+		pio: pinctrl@1000b000 {
+			compatible = "mediatek,mt8365-pinctrl";
+			reg = <0 0x1000b000 0 0x1000>;
+			mediatek,pctl-regmap = <&syscfg_pctl>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8365-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		keypad: keypad@10010000 {
+			compatible = "mediatek,mt6779-keypad";
+			reg = <0 0x10010000 0 0x1000>;
+			wakeup-source;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clk26m>;
+			clock-names = "kpd";
+			status = "disabled";
+		};
+
+		mcucfg: syscon@10200000 {
+			compatible = "mediatek,mt8365-mcucfg", "syscon";
+			reg = <0 0x10200000 0 0x2000>;
+			#clock-cells = <1>;
+		};
+
+		sysirq: interrupt-controller@10200a80 {
+			compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10200a80 0 0x20>;
+		};
+
+		infracfg_nao: infracfg@1020e000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x1020e000 0 0x1000>;
+		};
+
+		rng: rng@1020f000 {
+			compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+			reg = <0 0x1020f000 0 0x100>;
+			clocks = <&infracfg CLK_IFR_TRNG>;
+			clock-names = "rng";
+		};
+
+		apdma: dma-controller@11000280 {
+			compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+			reg = <0 0x11000280 0 0x80>,
+			      <0 0x11000300 0 0x80>,
+			      <0 0x11000380 0 0x80>,
+			      <0 0x11000400 0 0x80>,
+			      <0 0x11000580 0 0x80>,
+			      <0 0x11000600 0 0x80>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+			dma-requests = <6>;
+			clocks = <&infracfg CLK_IFR_AP_DMA>;
+			clock-names = "apdma";
+			#dma-cells = <1>;
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 0>, <&apdma 1>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 2>, <&apdma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x1000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 4>, <&apdma 5>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		pwm: pwm@11006000 {
+			compatible = "mediatek,mt8365-pwm";
+			reg = <0 0x11006000 0 0x1000>;
+			#pwm-cells = <2>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+				 <&infracfg CLK_IFR_PWM>,
+				 <&infracfg CLK_IFR_PWM1>,
+				 <&infracfg CLK_IFR_PWM2>,
+				 <&infracfg CLK_IFR_PWM3>;
+			clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+		};
+
+		spi: spi@1100a000 {
+			compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+			reg = <0 0x1100a000 0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_IFR_SPI0>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		ssusb: usb@11201000 {
+			compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+			reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+				 <&infracfg CLK_IFR_SSUSB_REF>,
+				 <&infracfg CLK_IFR_SSUSB_SYS>,
+				 <&infracfg CLK_IFR_ICUSB>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			usb_host: usb@11200000 {
+				compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+				reg = <0 0x11200000 0 0x1000>;
+				reg-names = "mac";
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+					 <&infracfg CLK_IFR_SSUSB_REF>,
+					 <&infracfg CLK_IFR_SSUSB_SYS>,
+					 <&infracfg CLK_IFR_ICUSB>,
+					 <&infracfg CLK_IFR_SSUSB_XHCI>;
+				clock-names = "sys_ck", "ref_ck", "mcu_ck",
+					      "dma_ck", "xhci_ck";
+				status = "disabled";
+			};
+		};
+
+		u3phy: phy@11cc0000 {
+			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#phy-cells = <1>;
+			ranges;
+
+			u2port0: usb-phy@11cc0000 {
+				reg = <0 0x11cc0000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@11cc1000 {
+				reg = <0 0x11cc1000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	systimer: timer@10017000 {
+		compatible = "mediatek,mt6795-systimer";
+		reg = <0 0x10017000 0 0x10>;
+		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>;
+		clock-names = "clk13m";
+	};
+};