diff mbox series

[v3,2/3] arm64: dts: ti: k3-am62-main: Add support for USB

Message ID 20230111132348.553061-3-sjoerd@collabora.com (mailing list archive)
State New, archived
Headers show
Series Improve K3-am625-sk support (USB, MMC) | expand

Commit Message

Sjoerd Simons Jan. 11, 2023, 1:23 p.m. UTC
From: Aswath Govindraju <a-govindraju@ti.com>

AM62 SoC has two instances of USB on it. Therefore, add support for the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[cherry-pick from vendor BSP]]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>

---

Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by

Changes in v2:
- Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 44 ++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

Comments

Vignesh Raghavendra Jan. 11, 2023, 6:20 p.m. UTC | #1
On 1/11/2023 6:53 PM, Sjoerd Simons wrote:
> From: Aswath Govindraju <a-govindraju@ti.com>
> 
> AM62 SoC has two instances of USB on it. Therefore, add support for the
> same.
> 
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> [cherry-pick from vendor BSP]]
> Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
> Tested-by: Martyn Welch <martyn.welch@collabora.com>
> 
> ---
> 
> Changes in v3:
> - Rebased against current ti-next aka 6.2-rc1
> - Add Martyn's tested-by
> 
> Changes in v2:
> - Rebase against linux-next 20221220
> 
>  arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 44 ++++++++++++++++++++++++
>  1 file changed, 44 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> index 466b94d1cee9..4da15e8c956f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
> @@ -555,6 +555,50 @@ sdhci2: mmc@fa20000 {
>  		status = "disabled";
>  	};
>  
> +	usbss0: dwc3-usb@f900000 {
> +		compatible = "ti,am62-usb";
> +		reg = <0x00 0x0f900000 0x00 0x800>;
> +		clocks = <&k3_clks 161 3>;
> +		clock-names = "ref";
> +		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
> +		ranges;
> +

Following the convention of the file, could you please set status =
"disabled" here and then set it to okay in board dts file (patch 3/3)

> +		usb0: usb@31000000 {
> +			compatible = "snps,dwc3";
> +			reg =<0x00 0x31000000 0x00 0x50000>;
> +			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> +				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> +			interrupt-names = "host", "peripheral";
> +			maximum-speed = "high-speed";
> +			dr_mode = "otg";
> +		};
> +	};
> +
> +	usbss1: dwc3-usb@f910000 {
> +		compatible = "ti,am62-usb";
> +		reg = <0x00 0x0f910000 0x00 0x800>;
> +		clocks = <&k3_clks 162 3>;
> +		clock-names = "ref";
> +		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
> +		ranges;
> +

Same here...

> +		usb1: usb@31100000 {
> +			compatible = "snps,dwc3";
> +			reg =<0x00 0x31100000 0x00 0x50000>;
> +			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> +				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> +			interrupt-names = "host", "peripheral";
> +			maximum-speed = "high-speed";
> +			dr_mode = "otg";
> +		};
> +	};
> +
>  	fss: bus@fc00000 {
>  		compatible = "simple-bus";
>  		reg = <0x00 0x0fc00000 0x00 0x70000>;
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 466b94d1cee9..4da15e8c956f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -555,6 +555,50 @@  sdhci2: mmc@fa20000 {
 		status = "disabled";
 	};
 
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	fss: bus@fc00000 {
 		compatible = "simple-bus";
 		reg = <0x00 0x0fc00000 0x00 0x70000>;