diff mbox series

[2/3] arm64: dts: meson-g12b: move common node into new odroid.dtsi

Message ID 20230122-topic-odroid-n2l-upstream-initial-v1-2-1ce5e08039d0@linaro.org (mailing list archive)
State New, archived
Headers show
Series arm64: meson-g12b: add initial support for Odroid-N2L | expand

Commit Message

Neil Armstrong Jan. 23, 2023, 2:07 p.m. UTC 
In order to introduce Odroid-N2L which is basically an Odroid-N2+
without some on-board peripherals (Ethernet, RTC, Hub, Jack),
move the common nodes into a new meson-g12b-odroid.dtsi which will
will be the common dtsi for all the Odroid-N2 derived boards.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 .../boot/dts/amlogic/meson-g12b-odroid-n2.dtsi     | 448 +--------------------
 arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi | 445 ++++++++++++++++++++
 2 files changed, 454 insertions(+), 439 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 667d2b774924..24d0442dffb2 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -4,17 +4,11 @@ 
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
-#include <dt-bindings/sound/meson-g12a-toacodec.h>
-#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+#include "meson-g12b-odroid.dtsi"
 
 / {
 	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
 		rtc0 = &rtc;
-		rtc1 = &vrtc;
 	};
 
 	dio2133: audio-amplifier-0 {
@@ -25,149 +19,6 @@  dio2133: audio-amplifier-0 {
 		status = "okay";
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	fan: gpio-fan {
-		compatible = "gpio-fan";
-		gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
-		/* Using Dummy Speed */
-		gpio-fan,speed-map = <0 0>, <1 1>;
-		#cooling-cells = <2>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-blue {
-			label = "n2:blue";
-			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	tf_io: gpio-regulator-tf_io {
-		compatible = "regulator-gpio";
-
-		regulator-name = "TF_IO";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
-		gpios-states = <0>;
-
-		states = <3300000 0>,
-			 <1800000 1>;
-	};
-
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	main_12v: regulator-main_12v {
-		compatible = "regulator-fixed";
-		regulator-name = "12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		vin-supply = <&main_12v>;
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-	};
-
-	vcc_1v8: regulator-vcc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-		/* FIXME: actually controlled by VDDCPU_B_EN */
-	};
-
-	vddcpu_a: regulator-vddcpu-a {
-		/*
-		 * MP8756GD Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_A";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		pwm-supply = <&main_12v>;
-
-		pwms = <&pwm_ab 0 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vddcpu_b: regulator-vddcpu-b {
-		/*
-		 * Silergy SY8120B1ABC Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_B";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		pwm-supply = <&main_12v>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	hub_5v: regulator-hub_5v {
 		compatible = "regulator-fixed";
 		regulator-name = "HUB_5V";
@@ -180,47 +31,6 @@  hub_5v: regulator-hub_5v {
 		enable-active-high;
 	};
 
-	usb_pwr_en: regulator-usb_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* Connected to the microUSB port power enable */
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&main_12v>;
-		regulator-always-on;
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "ODROID-N2";
@@ -354,102 +164,13 @@  &acodec {
 	status = "okay";
 };
 
-&arb {
-	status = "okay";
-};
-
-&cec_AO {
-	pinctrl-0 = <&cec_ao_a_h_pins>;
-	pinctrl-names = "default";
-	status = "disabled";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
-	pinctrl-0 = <&cec_ao_b_h_pins>;
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
 	pinctrl-names = "default";
 	status = "okay";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&clkc_audio {
-	status = "okay";
-};
-
-&cpu0 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu100 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu101 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu102 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu103 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu_thermal {
-	trips {
-		cpu_active: cpu-active {
-			temperature = <60000>; /* millicelsius */
-			hysteresis = <2000>; /* millicelsius */
-			type = "active";
-		};
-	};
-
-	cooling-maps {
-		map {
-			trip = <&cpu_active>;
-			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
-};
-
-&ddr_thermal {
-	trips {
-		ddr_active: ddr-active {
-			temperature = <60000>; /* millicelsius */
-			hysteresis = <2000>; /* millicelsius */
-			type = "active";
-		};
-	};
-
-	cooling-maps {
-		map {
-			trip = <&ddr_active>;
-			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
 };
 
 &ext_mdio {
@@ -468,27 +189,6 @@  external_phy: ethernet-phy@0 {
 	};
 };
 
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&external_phy>;
-	amlogic,tx-delay-ns = <2>;
-};
-
-&frddr_a {
-	status = "okay";
-};
-
-&frddr_b {
-	status = "okay";
-};
-
-&frddr_c {
-	status = "okay";
-};
-
 &gpio {
 	gpio-line-names =
 		/* GPIOZ */
@@ -549,26 +249,6 @@  hog-0 {
 	};
 };
 
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-	linux,rc-map-name = "rc-odroid";
-};
-
 &i2c3 {
 	status = "okay";
 	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
@@ -581,62 +261,11 @@  rtc: rtc@51 {
 	};
 };
 
-&pwm_ab {
-	pinctrl-0 = <&pwm_a_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
+&ir {
 	status = "okay";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-0 = <&remote_input_ao_pins>;
 	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-	vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&tf_io>;
-
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&flash_1v8>;
+	linux,rc-map-name = "rc-odroid";
 };
 
 /*
@@ -660,73 +289,14 @@  mx25u64: flash@0 {
 	};
 };
 
-&tdmif_b {
-	status = "okay";
-};
-
-&tdmif_c {
-	status = "okay";
-};
-
-&tdmin_a {
-	status = "okay";
-};
-
-&tdmin_b {
-	status = "okay";
-};
-
-&tdmin_c {
-	status = "okay";
-};
-
-&tdmin_lb {
-	status = "okay";
-};
-
-&tdmout_b {
-	status = "okay";
-};
-
-&tdmout_c {
-	status = "okay";
-};
-
 &toacodec {
 	status = "okay";
 };
 
-&tohdmitx {
-	status = "okay";
-};
-
-&toddr_a {
-	status = "okay";
-};
-
-&toddr_b {
-	status = "okay";
-};
-
-&toddr_c {
-	status = "okay";
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
 &usb {
-	status = "okay";
 	vbus-supply = <&usb_pwr_en>;
 };
 
-&usb2_phy0 {
-	phy-supply = <&vcc_5v>;
-};
-
 &usb2_phy1 {
 	/* Enable the hub which is connected to this port */
 	phy-supply = <&hub_5v>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi
new file mode 100644
index 000000000000..9e12a34b2840
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi
@@ -0,0 +1,445 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		rtc1 = &vrtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
+		/* Using Dummy Speed */
+		gpio-fan,speed-map = <0 0>, <1 1>;
+		#cooling-cells = <2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			label = "n2:blue";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+			 <1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&main_12v>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vddcpu_a: regulator-vddcpu-a {
+		/*
+		 * MP8756GD Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_A";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		pwm-supply = <&main_12v>;
+
+		pwms = <&pwm_ab 0 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddcpu_b: regulator-vddcpu-b {
+		/*
+		 * Silergy SY8120B1ABC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_B";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		pwm-supply = <&main_12v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu100 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu101 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu102 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu103 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu_thermal {
+	trips {
+		cpu_active: cpu-active {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpu_active>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&ddr_thermal {
+	trips {
+		ddr_active: ddr-active {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&ddr_active>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&pwm_ab {
+	pinctrl-0 = <&pwm_a_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+	status = "okay";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmif_c {
+	status = "okay";
+};
+
+&tdmin_a {
+	status = "okay";
+};
+
+&tdmin_b {
+	status = "okay";
+};
+
+&tdmin_c {
+	status = "okay";
+};
+
+&tdmin_lb {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tdmout_c {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&toddr_a {
+	status = "okay";
+};
+
+&toddr_b {
+	status = "okay";
+};
+
+&toddr_c {
+	status = "okay";
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};