diff mbox series

[v5,09/10] arm64: dts: freescale: add initial apalis imx8 aka quadmax module support

Message ID 20230126110833.264439-10-marcel@ziswiler.com (mailing list archive)
State New, archived
Headers show
Series arm64: dts: freescale: prepare and add apalis imx8 support | expand

Commit Message

Marcel Ziswiler Jan. 26, 2023, 11:08 a.m. UTC
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This patch adds the device tree to support Toradex Apalis iMX8 [1] aka
QuadMax a computer on module which can be used on different carrier
boards.

The module consists of an NXP i.MX 8 family SoC (either i.MX 8QuadMax or
8QuadPlus), two PF8100 PMICs, a KSZ9131 Gigabit Ethernet PHY, 2, 4 or 8
GB of LPDDR4 RAM, an eMMC, an SGTL5000 analogue audio codec, an USB3503A
USB HSIC hub, an optional I2C EEPROM plus an optional Bluetooth/Wi-Fi
module.

Anything that is not self-contained on the module is disabled by
default.

The carrier board device trees in the next patch will include the
module's device tree and enable the supported peripherals of the
carrier board.

Some level of display functionality just landed upstream but requires
further integration/testing on our side. Therefore, currently only
basic console UART, eMMC and Ethernet functionality work fine.

As there is no i.MX 8QuadPlus device tree upstream those have been
dropped. However, apart from an error message during boot about it
failing to bring up the second Cortex-A72 core this boots fine on
QuadPlus' as well.

[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---

(no changes since v1)

 .../boot/dts/freescale/imx8-apalis-v1.1.dtsi  | 1453 +++++++++++++++++
 .../dts/freescale/imx8qm-apalis-v1.1.dtsi     |   16 +
 .../boot/dts/freescale/imx8qm-apalis.dtsi     |  340 ++++
 3 files changed, 1809 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi

Comments

Shawn Guo Jan. 29, 2023, 3:19 a.m. UTC | #1
On Thu, Jan 26, 2023 at 12:08:32PM +0100, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This patch adds the device tree to support Toradex Apalis iMX8 [1] aka
> QuadMax a computer on module which can be used on different carrier
> boards.
> 
> The module consists of an NXP i.MX 8 family SoC (either i.MX 8QuadMax or
> 8QuadPlus), two PF8100 PMICs, a KSZ9131 Gigabit Ethernet PHY, 2, 4 or 8
> GB of LPDDR4 RAM, an eMMC, an SGTL5000 analogue audio codec, an USB3503A
> USB HSIC hub, an optional I2C EEPROM plus an optional Bluetooth/Wi-Fi
> module.
> 
> Anything that is not self-contained on the module is disabled by
> default.
> 
> The carrier board device trees in the next patch will include the
> module's device tree and enable the supported peripherals of the
> carrier board.
> 
> Some level of display functionality just landed upstream but requires
> further integration/testing on our side. Therefore, currently only
> basic console UART, eMMC and Ethernet functionality work fine.
> 
> As there is no i.MX 8QuadPlus device tree upstream those have been
> dropped. However, apart from an error message during boot about it
> failing to bring up the second Cortex-A72 core this boots fine on
> QuadPlus' as well.
> 
> [1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> ---
> 
> (no changes since v1)
> 
>  .../boot/dts/freescale/imx8-apalis-v1.1.dtsi  | 1453 +++++++++++++++++
>  .../dts/freescale/imx8qm-apalis-v1.1.dtsi     |   16 +
>  .../boot/dts/freescale/imx8qm-apalis.dtsi     |  340 ++++
>  3 files changed, 1809 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi b/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
> new file mode 100644
> index 000000000000..3960ef30464e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
> @@ -0,0 +1,1453 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2022 Toradex
> + */
> +
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> +	chosen {
> +		stdout-path = &lpuart1;
> +	};
> +
> +	/* Apalis BKL1 */
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		brightness-levels = <0 45 63 88 119 158 203 255>;
> +		default-brightness-level = <4>;
> +		enable-gpios = <&lsio_gpio1 4 GPIO_ACTIVE_HIGH>; /* Apalis BKL1_ON */
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_bkl_on>;
> +		/* TODO: hook-up to Apalis BKL1_PWM */
> +		status = "disabled";
> +	};
> +
> +	gpio_fan: gpio-fan {
> +		compatible = "gpio-fan";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio8>;
> +		gpios = <&lsio_gpio3 28 GPIO_ACTIVE_HIGH>;
> +		gpio-fan,speed-map = <	 0 0
> +				      3000 1>;
> +	};
> +
> +/* TODO: LVDS Panel */
> +
> +/* TODO: Shared PCIe/SATA Reference Clock */
> +
> +/* TODO: PCIe Wi-Fi Reference Clock */
> +
> +	/*
> +	 * Power management bus used to control LDO1OUT of the
> +	 * second PMIC PF8100. This is used for controlling voltage levels of
> +	 * typespecific RGMII signals and Apalis UART2_RTS UART2_CTS.
> +	 *
> +	 * IMX_SC_R_BOARD_R1 for 3.3V
> +	 * IMX_SC_R_BOARD_R2 for 1.8V
> +	 * IMX_SC_R_BOARD_R3 for 2.5V
> +	 * Note that for 2.5V operation the pad muxing needs to be changed,
> +	 * compare with PSW_OVR field of IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD.
> +	 *
> +	 * those power domains are mutually exclusive.
> +	 */
> +	reg_ext_rgmii: regulator-ext-rgmii {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDD_EXT_RGMII (LDO1)";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		power-domains = <&pd IMX_SC_R_BOARD_R1>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	reg_module_3v3: regulator-module-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "+V3.3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	reg_module_3v3_avdd: regulator-module-3v3-avdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "+V3.3_AUDIO";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	reg_module_wifi: regulator-module-wifi {
> +		compatible = "regulator-fixed";
> +		gpio = <&lsio_gpio1 28 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_wifi_pdn>;
> +		regulator-name = "wifi_pwrdn_fake_regulator";
> +		regulator-settling-time-us = <100>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	reg_pcie_switch: regulator-pcie-switch {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio7>;
> +		gpio = <&lsio_gpio3 26 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-name = "pcie_switch";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		startup-delay-us = <100000>;
> +	};
> +
> +	reg_usb_host_vbus: regulator-usb-host-vbus {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_usbh_en>;
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			/* Apalis USBH_EN */
> +			gpio = <&lsio_gpio4 4 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +			regulator-always-on;
> +	};
> +
> +	reg_usb_hsic: regulator-usb-hsic {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb-hsic-dummy";
> +		regulator-min-microvolt = <3000000>;
> +		regulator-max-microvolt = <3000000>;
> +	};
> +
> +	reg_usb_phy: regulator-usb-hsic1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb-phy-dummy";
> +		regulator-min-microvolt = <3000000>;
> +		regulator-max-microvolt = <3000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		decoder_boot: decoder_boot@84000000 {

Hyphen is more preferable than underscore in node name.

> +			no-map;
> +			reg = <0 0x84000000 0 0x2000000>;
> +		};
> +
> +		encoder1_boot: encoder1_boot@86000000 {
> +			no-map;
> +			reg = <0 0x86000000 0 0x200000>;
> +		};
> +
> +		encoder2_boot: encoder2_boot@86200000 {
> +			no-map;
> +			reg = <0 0x86200000 0 0x200000>;
> +		};
> +
> +		/*
> +		 * reserved-memory layout
> +		 * 0x8800_0000 ~ 0x8FFF_FFFF is reserved for M4
> +		 * Shouldn't be used at A core and Linux side.
> +		 *
> +		 */
> +		m4_reserved: m4@88000000 {
> +			no-map;
> +			reg = <0 0x88000000 0 0x8000000>;
> +		};
> +
> +		rpmsg_reserved: rpmsg@90000000 {

rpmsg@90200000

> +			no-map;
> +			reg = <0 0x90200000 0 0x200000>;
> +		};
> +
> +		vdevbuffer: vdevbuffer@90400000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0 0x90400000 0 0x100000>;
> +			no-map;
> +		};
> +
> +		decoder_rpc: decoder_rpc@92000000 {

Hyphen for node name.

> +			no-map;
> +			reg = <0 0x92000000 0 0x200000>;
> +		};
> +
> +		dsp_reserved: dsp@92400000 {
> +			no-map;
> +			reg = <0 0x92400000 0 0x2000000>;
> +		};
> +
> +		encoder1_rpc: encoder1_rpc@94400000 {
> +			no-map;
> +			reg = <0 0x94400000 0 0x700000>;
> +		};
> +
> +		encoder2_rpc: encoder2_rpc@94b00000 {
> +			no-map;
> +			reg = <0 0x94b00000 0 0x700000>;
> +		};
> +
> +		/* global autoconfigured region for contiguous allocations */
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			reusable;
> +			size = <0 0x3c000000>;
> +			alloc-ranges = <0 0xc0000000 0 0x3c000000>;
> +			linux,cma-default;
> +		};
> +	};
> +
> +	/* TODO: Apalis Analogue Audio */
> +
> +	/* TODO: HDMI Audio */
> +
> +	/* TODO: Apalis SPDIF1 */
> +
> +	touchscreen: vf50-touchscreen {

touchscreen for node name.

> +		compatible = "toradex,vf50-touchscreen";
> +		io-channels = <&adc1 2>,<&adc1 1>,

Missing space after the first comma.

> +			      <&adc1 0>,<&adc1 3>;
> +		interrupt-parent = <&lsio_gpio3>;
> +		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "idle","default";

Ditto

> +		pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>;
> +		pinctrl-1 = <&pinctrl_adc1>, <&pinctrl_touchctrl_gpios>;
> +		vf50-ts-min-pressure = <200>;
> +		xp-gpios = <&lsio_gpio2 4 GPIO_ACTIVE_LOW>;
> +		xm-gpios = <&lsio_gpio2 5 GPIO_ACTIVE_HIGH>;
> +		yp-gpios = <&lsio_gpio2 17 GPIO_ACTIVE_LOW>;
> +		ym-gpios = <&lsio_gpio2 21 GPIO_ACTIVE_HIGH>;
> +		/*
> +		 * NOTE: you must remove the pinctrl-adc1 from the adc1
> +		 * node below to use the touchscreen
> +		 */
> +		status = "disabled";
> +	};
> +
> +};
> +
> +&adc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc0>;
> +};
> +
> +&adc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc1>;
> +};
> +
> +/* TODO: Asynchronous Sample Rate Converter (ASRC) */
> +
> +/* Apalis ETH1 */
> +&fec1 {
> +	fsl,magic-packet;
> +	phy-handle = <&ethphy0>;
> +	phy-mode = "rgmii-id";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	pinctrl-1 = <&pinctrl_fec1_sleep>;
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@7 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			interrupt-parent = <&lsio_gpio1>;
> +			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
> +			micrel,led-mode = <0>;
> +			reg = <7>;

Can this be put right after compatible?

> +			reset-assert-us = <2>;
> +			reset-deassert-us = <2>;
> +			reset-gpios = <&lsio_gpio1 11 GPIO_ACTIVE_LOW>;
> +			reset-names = "phy-reset";
> +		};
> +	};
> +};
> +
> +/* Apalis CAN1 */
> +&flexcan1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +};
> +
> +/* Apalis CAN2 */
> +&flexcan2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan2>;
> +};
> +
> +/* Apalis CAN3 (optional) */
> +&flexcan3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan3>;
> +};
> +
> +/* TODO: Apalis HDMI1 */
> +
> +/* On-module I2C */
> +&i2c1 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpi2c1>;
> +	status = "okay";
> +
> +	/* TODO: Audio Codec */
> +
> +	/* USB3503A */
> +	usb3503@8 {

usb-hub for node name?

> +		compatible = "smsc,usb3503a";
> +		connect-gpios = <&lsio_gpio0 31 GPIO_ACTIVE_LOW>;
> +		initial-mode = <1>;
> +		intn-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usb3503a>;
> +		refclk-frequency = <25000000>;
> +		reg = <0x08>;

Put it right after compatible?

> +		reset-gpios = <&lsio_gpio1 2 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +/* Apalis I2C1 */
> +&i2c2 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpi2c2>;
> +
> +	atmel_mxt_ts: touch@4a {
> +		compatible = "atmel,maxtouch";
> +		reg = <0x4a>;
> +		interrupt-parent = <&lsio_gpio4>;
> +		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;		/* Apalis GPIO5 */
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio5>, <&pinctrl_gpio6>;
> +		reset-gpios = <&lsio_gpio4 2 GPIO_ACTIVE_LOW>;	/* Apalis GPIO6 */
> +		status = "disabled";
> +	};
> +
> +	/* M41T0M6 real time clock on carrier board */
> +	rtc_i2c: rtc@68 {
> +		compatible = "st,m41t0";
> +		reg = <0x68>;
> +		status = "disabled";
> +	};
> +};
> +
> +/* Apalis I2C3 (CAM) */
> +&i2c3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpi2c3>;
> +};
> +
> +&jpegdec {
> +	status = "okay";
> +};
> +
> +&jpegenc {
> +	status = "okay";
> +};
> +
> +/* TODO: Apalis LVDS1 */
> +
> +/* Apalis SPI1 */
> +&lpspi0 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	cs-gpios = <&lsio_gpio3 5 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpspi0>;
> +};
> +
> +/* Apalis SPI2 */
> +&lpspi2 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	cs-gpios = <&lsio_gpio3 10 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpspi2>;
> +};
> +
> +/* Apalis UART3 */
> +&lpuart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart0>;
> +};
> +
> +/* Apalis UART1 */
> +&lpuart1 {
> +	dma-names = "","";

What is this for?

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart1>;
> +};
> +
> +/* Apalis UART4 */
> +&lpuart2 {
> +	dma-names = "","";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart2>;
> +};
> +
> +/* Apalis UART2 */
> +&lpuart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart3>;
> +};
> +
> +&lsio_gpio0 {
> +	gpio-line-names = "MXM3_279",
> +			  "MXM3_277",
> +			  "MXM3_135",
> +			  "MXM3_203",
> +			  "MXM3_201",
> +			  "MXM3_275",
> +			  "MXM3_110",
> +			  "MXM3_120",
> +			  "MXM3_1/GPIO1",
> +			  "MXM3_3/GPIO2",
> +			  "MXM3_124",
> +			  "MXM3_122",
> +			  "MXM3_5/GPIO3",
> +			  "MXM3_7/GPIO4",
> +			  "",
> +			  "",
> +			  "MXM3_4",
> +			  "MXM3_211",
> +			  "MXM3_209",
> +			  "MXM3_2",
> +			  "MXM3_136",
> +			  "MXM3_134",
> +			  "MXM3_6",
> +			  "MXM3_8",
> +			  "MXM3_112",
> +			  "MXM3_118",
> +			  "MXM3_114",
> +			  "MXM3_116";
> +};
> +
> +&lsio_gpio1 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_286",
> +			  "",
> +			  "MXM3_87",
> +			  "MXM3_99",
> +			  "MXM3_138",
> +			  "MXM3_140",
> +			  "MXM3_239",
> +			  "",
> +			  "MXM3_281",
> +			  "MXM3_283",
> +			  "MXM3_126",
> +			  "MXM3_132",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_173",
> +			  "MXM3_175",
> +			  "MXM3_123";
> +
> +	hdmi-ctrl-hog {
> +		gpio-hog;
> +		gpios = <30 GPIO_ACTIVE_HIGH>;
> +		line-name = "CONNECTOR_IS_HDMI";
> +		/* Set signals depending on HDP device type, 0 DP, 1 HDMI */
> +		output-high;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_hdmi_ctrl>;
> +	};
> +};
> +
> +&lsio_gpio2 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_198",
> +			  "MXM3_35",
> +			  "MXM3_164",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_217",
> +			  "MXM3_215",
> +			  "",
> +			  "",
> +			  "MXM3_193",
> +			  "MXM3_194",
> +			  "MXM3_37",
> +			  "",
> +			  "MXM3_271",
> +			  "MXM3_273",
> +			  "MXM3_195",
> +			  "MXM3_197",
> +			  "MXM3_177",
> +			  "MXM3_179",
> +			  "MXM3_181",
> +			  "MXM3_183",
> +			  "MXM3_185",
> +			  "MXM3_187";
> +
> +	/*
> +	 * Add GPIO2_20 as a wakeup source:
> +	 * Pin:  101	SC_P_SPI3_CS0 (MXM3_37/WAKE1_MICO)
> +	 * Type: 5	SC_PAD_WAKEUP_FALL_EDGE
> +	 * Line: 20
> +	 */
> +	 pad-wakeup = <IMX8QM_SPI3_CS0 5 20>;
> +	 pad-wakeup-num = <1>;
> +
> +	pcie-wifi-hog {
> +		gpio-hog;
> +		gpios = <11 GPIO_ACTIVE_HIGH>;
> +		line-name = "PCIE_WIFI_CLK";
> +		output-high;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pcie_wifi_refclk>;
> +	};
> +};
> +
> +&lsio_gpio3 {
> +	gpio-line-names = "MXM3_191",
> +			  "",
> +			  "MXM3_221",
> +			  "MXM3_225",
> +			  "MXM3_223",
> +			  "MXM3_227",
> +			  "MXM3_200",
> +			  "MXM3_235",
> +			  "MXM3_231",
> +			  "MXM3_229",
> +			  "MXM3_233",
> +			  "MXM3_204",
> +			  "MXM3_196",
> +			  "",
> +			  "MXM3_202",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_305",
> +			  "MXM3_307",
> +			  "MXM3_309",
> +			  "MXM3_311",
> +			  "MXM3_315",
> +			  "MXM3_317",
> +			  "MXM3_319",
> +			  "MXM3_321",
> +			  "MXM3_15/GPIO7",
> +			  "MXM3_63",
> +			  "MXM3_17/GPIO8",
> +			  "MXM3_12",
> +			  "MXM3_14",
> +			  "MXM3_16";
> +};
> +
> +&lsio_gpio4 {
> +	gpio-line-names = "MXM3_18",
> +			  "MXM3_11/GPIO5",
> +			  "MXM3_13/GPIO6",
> +			  "MXM3_274",
> +			  "MXM3_84",
> +			  "MXM3_262",
> +			  "MXM3_96",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_190",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_269",
> +			  "MXM3_251",
> +			  "MXM3_253",
> +			  "MXM3_295",
> +			  "MXM3_299",
> +			  "MXM3_301",
> +			  "MXM3_297",
> +			  "MXM3_293",
> +			  "MXM3_291",
> +			  "MXM3_289",
> +			  "MXM3_287";
> +
> +	/* Enable pcie root / sata ref clock unconditionally */
> +	pcie-sata-hog {
> +		gpio-hog;
> +		gpios = <11 GPIO_ACTIVE_HIGH>;
> +		line-name = "PCIE_SATA_CLK";
> +		output-high;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pcie_sata_refclk>;
> +	};
> +};
> +
> +&lsio_gpio5 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_150",
> +			  "MXM3_160",
> +			  "MXM3_162",
> +			  "MXM3_144",
> +			  "MXM3_146",
> +			  "MXM3_148",
> +			  "MXM3_152",
> +			  "MXM3_156",
> +			  "MXM3_158",
> +			  "MXM3_159",
> +			  "MXM3_184",
> +			  "MXM3_180",
> +			  "MXM3_186",
> +			  "MXM3_188",
> +			  "MXM3_176",
> +			  "MXM3_178";
> +};
> +
> +&lsio_gpio6 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_261",
> +			  "MXM3_263",
> +			  "MXM3_259",
> +			  "MXM3_257",
> +			  "MXM3_255",
> +			  "MXM3_128",
> +			  "MXM3_130",
> +			  "MXM3_265",
> +			  "MXM3_249",
> +			  "MXM3_247",
> +			  "MXM3_245",
> +			  "MXM3_243";
> +};
> +
> +/* Apalis PWM3, MXM3 pin 6 */
> +&lsio_pwm0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm0>;
> +	#pwm-cells = <3>;
> +};
> +
> +/* Apalis PWM4, MXM3 pin 8 */
> +&lsio_pwm1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm1>;
> +	#pwm-cells = <3>;
> +};
> +
> +/* Apalis PWM1, MXM3 pin 2 */
> +&lsio_pwm2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm2>;
> +	#pwm-cells = <3>;
> +};
> +
> +/* Apalis PWM2, MXM3 pin 4 */
> +&lsio_pwm3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm3>;
> +	#pwm-cells = <3>;
> +};
> +
> +/* TODO: Messaging Units */
> +
> +/* TODO: Apalis PCIE1 */
> +
> +/* TODO: On-module Wi-Fi */
> +
> +/* TODO: Apalis BKL1_PWM */
> +
> +/* TODO: Apalis DAP1 */
> +
> +/* TODO: Analogue Audio */
> +
> +/* TODO: Apalis SATA1 */
> +
> +/* TODO: Apalis SPDIF1 */
> +
> +/* TODO: Thermal Zones */
> +
> +/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
> +
> +/* TODO: Apalis USBH4 */
> +
> +/* Apalis USBO1 */
> +&usbphy1 {
> +	phy-3p0-supply = <&reg_usb_phy>;
> +	status = "okay";
> +};
> +
> +&usbotg1 {
> +	adp-disable;
> +	ci-disable-lpm;
> +	hnp-disable;
> +	over-current-active-low;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg1>;

We generally want to put such generic properties before device specific
ones.

Shawn

> +	power-active-high;
> +	srp-disable;
> +};
> +
> +/* On-module eMMC */
> +&usdhc1 {
> +	bus-width = <8>;
> +	non-removable;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> +	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> +	status = "okay";
> +};
> +
> +/* Apalis MMC1 */
> +&usdhc2 {
> +	bus-width = <8>;
> +	cd-gpios = <&lsio_gpio2 9 GPIO_ACTIVE_LOW>; /* Apalis MMC1_CD# */
> +	no-1-8-v;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
> +	pinctrl-0 = <&pinctrl_usdhc2_4bit>,
> +		    <&pinctrl_usdhc2_8bit>,
> +		    <&pinctrl_mmc1_cd>;
> +	pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>,
> +		    <&pinctrl_usdhc2_8bit_100mhz>,
> +		    <&pinctrl_mmc1_cd>;
> +	pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>,
> +		    <&pinctrl_usdhc2_8bit_200mhz>,
> +		    <&pinctrl_mmc1_cd>;
> +	pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>,
> +		    <&pinctrl_usdhc2_8bit_sleep>,
> +		    <&pinctrl_mmc1_cd_sleep>;
> +};
> +
> +/* Apalis SD1 */
> +&usdhc3 {
> +	bus-width = <4>;
> +	cd-gpios = <&lsio_gpio4 12 GPIO_ACTIVE_LOW>; /* Apalis SD1_CD# */
> +	no-1-8-v;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_sd1_cd>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_sd1_cd>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_sd1_cd>;
> +};
> +
> +/* TODO: Video Processing Unit (driver upstream but device tree part missing) */
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
> +		    <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
> +		    <&pinctrl_gpio3>, <&pinctrl_gpio4>, <&pinctrl_gpio_keys>,
> +		    <&pinctrl_gpio_usbh_oc_n>, <&pinctrl_lpuart1ctrl>,
> +		    <&pinctrl_lvds0_i2c0_gpio>, <&pinctrl_lvds1_i2c0_gpios>,
> +		    <&pinctrl_mipi_dsi_0_1_en>, <&pinctrl_mipi_dsi1_gpios>,
> +		    <&pinctrl_mlb_gpios>, <&pinctrl_qspi1a_gpios>,
> +		    <&pinctrl_sata1_act>, <&pinctrl_sim0_gpios>,
> +		    <&pinctrl_usdhc1_gpios>;
> +
> +	/* Apalis AN1_ADC */
> +	pinctrl_adc0: adc0grp {
> +		fsl,pins = /* Apalis AN1_ADC0 */
> +			   <IMX8QM_ADC_IN0_DMA_ADC0_IN0				0xc0000060>,
> +			   /* Apalis AN1_ADC1 */
> +			   <IMX8QM_ADC_IN1_DMA_ADC0_IN1				0xc0000060>,
> +			   /* Apalis AN1_ADC2 */
> +			   <IMX8QM_ADC_IN2_DMA_ADC0_IN2				0xc0000060>,
> +			   /* Apalis AN1_TSWIP_ADC3 */
> +			   <IMX8QM_ADC_IN3_DMA_ADC0_IN3				0xc0000060>;
> +	};
> +
> +	/* Apalis AN1_TS */
> +	pinctrl_adc1: adc1grp {
> +		fsl,pins = /* Apalis AN1_TSPX */
> +			   <IMX8QM_ADC_IN4_DMA_ADC1_IN0				0xc0000060>,
> +			   /* Apalis AN1_TSMX */
> +			   <IMX8QM_ADC_IN5_DMA_ADC1_IN1				0xc0000060>,
> +			   /* Apalis AN1_TSPY */
> +			   <IMX8QM_ADC_IN6_DMA_ADC1_IN2				0xc0000060>,
> +			   /* Apalis AN1_TSMY */
> +			   <IMX8QM_ADC_IN7_DMA_ADC1_IN3				0xc0000060>;
> +	};
> +
> +	/* Apalis CAM1 */
> +	pinctrl_cam1_gpios: cam1gpiosgrp {
> +		fsl,pins = /* Apalis CAM1_D7 */
> +			   <IMX8QM_MIPI_DSI1_I2C0_SCL_LSIO_GPIO1_IO20		0x00000021>,
> +			   /* Apalis CAM1_D6 */
> +			   <IMX8QM_MIPI_DSI1_I2C0_SDA_LSIO_GPIO1_IO21		0x00000021>,
> +			   /* Apalis CAM1_D5 */
> +			   <IMX8QM_ESAI0_TX0_LSIO_GPIO2_IO26			0x00000021>,
> +			   /* Apalis CAM1_D4 */
> +			   <IMX8QM_ESAI0_TX1_LSIO_GPIO2_IO27			0x00000021>,
> +			   /* Apalis CAM1_D3 */
> +			   <IMX8QM_ESAI0_TX2_RX3_LSIO_GPIO2_IO28		0x00000021>,
> +			   /* Apalis CAM1_D2 */
> +			   <IMX8QM_ESAI0_TX3_RX2_LSIO_GPIO2_IO29		0x00000021>,
> +			   /* Apalis CAM1_D1 */
> +			   <IMX8QM_ESAI0_TX4_RX1_LSIO_GPIO2_IO30		0x00000021>,
> +			   /* Apalis CAM1_D0 */
> +			   <IMX8QM_ESAI0_TX5_RX0_LSIO_GPIO2_IO31		0x00000021>,
> +			   /* Apalis CAM1_PCLK */
> +			   <IMX8QM_MCLK_IN0_LSIO_GPIO3_IO00			0x00000021>,
> +			   /* Apalis CAM1_MCLK */
> +			   <IMX8QM_SPI3_SDO_LSIO_GPIO2_IO18			0x00000021>,
> +			   /* Apalis CAM1_VSYNC */
> +			   <IMX8QM_ESAI0_SCKR_LSIO_GPIO2_IO24			0x00000021>,
> +			   /* Apalis CAM1_HSYNC */
> +			   <IMX8QM_ESAI0_SCKT_LSIO_GPIO2_IO25			0x00000021>;
> +	};
> +
> +	/* Apalis DAP1 */
> +	pinctrl_dap1_gpios: dap1gpiosgrp {
> +		fsl,pins = /* Apalis DAP1_MCLK */
> +			   <IMX8QM_SPI3_SDI_LSIO_GPIO2_IO19			0x00000021>,
> +			   /* Apalis DAP1_D_OUT */
> +			   <IMX8QM_SAI1_RXC_LSIO_GPIO3_IO12			0x00000021>,
> +			   /* Apalis DAP1_RESET */
> +			   <IMX8QM_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000021>,
> +			   /* Apalis DAP1_BIT_CLK */
> +			   <IMX8QM_SPI0_CS1_LSIO_GPIO3_IO06			0x00000021>,
> +			   /* Apalis DAP1_D_IN */
> +			   <IMX8QM_SAI1_RXFS_LSIO_GPIO3_IO14			0x00000021>,
> +			   /* Apalis DAP1_SYNC */
> +			   <IMX8QM_SPI2_CS1_LSIO_GPIO3_IO11			0x00000021>,
> +			   /* On-module Wi-Fi_I2S_EN# */
> +			   <IMX8QM_ESAI1_TX5_RX0_LSIO_GPIO2_IO13		0x00000021>;
> +	};
> +
> +	/* Apalis LCD1_G1+2 */
> +	pinctrl_esai0_gpios: esai0gpiosgrp {
> +		fsl,pins = /* Apalis LCD1_G1 */
> +			   <IMX8QM_ESAI0_FSR_LSIO_GPIO2_IO22			0x00000021>,
> +			   /* Apalis LCD1_G2 */
> +			   <IMX8QM_ESAI0_FST_LSIO_GPIO2_IO23			0x00000021>;
> +	};
> +
> +	/* On-module Gigabit Ethernet PHY Micrel KSZ9031 for Apalis GLAN */
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = /* Use pads in 3.3V mode */
> +			   <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
> +			   <IMX8QM_ENET0_MDC_CONN_ENET0_MDC				0x06000020>,
> +			   <IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO				0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC			0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC			0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x06000020>,
> +			   <IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x06000020>,
> +			   <IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M	0x06000020>,
> +			   /* On-module ETH_RESET# */
> +			   <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x06000020>,
> +			   /* On-module ETH_INT# */
> +			   <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29			0x04000060>;
> +	};
> +
> +	pinctrl_fec1_sleep: fec1-sleepgrp {
> +		fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD		0x000014a0>,
> +			   <IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14			0x04000040>,
> +			   <IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13			0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08		0x04000040>,
> +			   <IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09		0x04000040>,
> +			   <IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15	0x04000040>,
> +			   <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11			0x06000020>,
> +			   <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29		0x04000040>;
> +	};
> +
> +	/* Apalis LCD1_ */
> +	pinctrl_fec2_gpios: fec2gpiosgrp {
> +		fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD		0x000014a0>,
> +			   /* Apalis LCD1_R1 */
> +			   <IMX8QM_ENET1_MDC_LSIO_GPIO4_IO18			0x00000021>,
> +			   /* Apalis LCD1_R0 */
> +			   <IMX8QM_ENET1_MDIO_LSIO_GPIO4_IO17			0x00000021>,
> +			   /* Apalis LCD1_G0 */
> +			   <IMX8QM_ENET1_REFCLK_125M_25M_LSIO_GPIO4_IO16	0x00000021>,
> +			   /* Apalis LCD1_R7 */
> +			   <IMX8QM_ENET1_RGMII_RX_CTL_LSIO_GPIO6_IO17		0x00000021>,
> +			   /* Apalis LCD1_DE */
> +			   <IMX8QM_ENET1_RGMII_RXD0_LSIO_GPIO6_IO18		0x00000021>,
> +			   /* Apalis LCD1_HSYNC */
> +			   <IMX8QM_ENET1_RGMII_RXD1_LSIO_GPIO6_IO19		0x00000021>,
> +			   /* Apalis LCD1_VSYNC */
> +			   <IMX8QM_ENET1_RGMII_RXD2_LSIO_GPIO6_IO20		0x00000021>,
> +			   /* Apalis LCD1_PCLK */
> +			   <IMX8QM_ENET1_RGMII_RXD3_LSIO_GPIO6_IO21		0x00000021>,
> +			   /* Apalis LCD1_R6 */
> +			   <IMX8QM_ENET1_RGMII_TX_CTL_LSIO_GPIO6_IO11		0x00000021>,
> +			   /* Apalis LCD1_R5 */
> +			   <IMX8QM_ENET1_RGMII_TXC_LSIO_GPIO6_IO10		0x00000021>,
> +			   /* Apalis LCD1_R4 */
> +			   <IMX8QM_ENET1_RGMII_TXD0_LSIO_GPIO6_IO12		0x00000021>,
> +			   /* Apalis LCD1_R3 */
> +			   <IMX8QM_ENET1_RGMII_TXD1_LSIO_GPIO6_IO13		0x00000021>,
> +			   /* Apalis LCD1_R2 */
> +			   <IMX8QM_ENET1_RGMII_TXD2_LSIO_GPIO6_IO14		0x00000021>;
> +	};
> +
> +	/* Apalis CAN1 */
> +	pinctrl_flexcan1: flexcan0grp {
> +		fsl,pins = <IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX			0x00000021>,
> +			   <IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX			0x00000021>;
> +	};
> +
> +	/* Apalis CAN2 */
> +	pinctrl_flexcan2: flexcan1grp {
> +		fsl,pins = <IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX			0x00000021>,
> +			   <IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX			0x00000021>;
> +	};
> +
> +	/* Apalis CAN3 (optional) */
> +	pinctrl_flexcan3: flexcan2grp {
> +		fsl,pins = <IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX			0x00000021>,
> +			   <IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX			0x00000021>;
> +	};
> +
> +	/* Apalis GPIO1 */
> +	pinctrl_gpio1: gpio1grp {
> +		fsl,pins = <IMX8QM_M40_GPIO0_00_LSIO_GPIO0_IO08			0x06000021>;
> +	};
> +
> +	/* Apalis GPIO2 */
> +	pinctrl_gpio2: gpio2grp {
> +		fsl,pins = <IMX8QM_M40_GPIO0_01_LSIO_GPIO0_IO09			0x06000021>;
> +	};
> +
> +	/* Apalis GPIO3 */
> +	pinctrl_gpio3: gpio3grp {
> +		fsl,pins = <IMX8QM_M41_GPIO0_00_LSIO_GPIO0_IO12			0x06000021>;
> +	};
> +
> +	/* Apalis GPIO4 */
> +	pinctrl_gpio4: gpio4grp {
> +		fsl,pins = <IMX8QM_M41_GPIO0_01_LSIO_GPIO0_IO13			0x06000021>;
> +	};
> +
> +	/* Apalis GPIO5 */
> +	pinctrl_gpio5: gpio5grp {
> +		fsl,pins = <IMX8QM_FLEXCAN2_RX_LSIO_GPIO4_IO01			0x06000021>;
> +	};
> +
> +	/* Apalis GPIO6 */
> +	pinctrl_gpio6: gpio6grp {
> +		fsl,pins = <IMX8QM_FLEXCAN2_TX_LSIO_GPIO4_IO02			0x00000021>;
> +	};
> +
> +	/* Apalis GPIO7 */
> +	pinctrl_gpio7: gpio7grp {
> +		fsl,pins = <IMX8QM_MLB_SIG_LSIO_GPIO3_IO26			0x00000021>;
> +	};
> +
> +	/* Apalis GPIO8 */
> +	pinctrl_gpio8: gpio8grp {
> +		fsl,pins = <IMX8QM_MLB_DATA_LSIO_GPIO3_IO28			0x00000021>;
> +	};
> +
> +	/* Apalis BKL1_ON */
> +	pinctrl_gpio_bkl_on: gpiobklongrp {
> +		fsl,pins = <IMX8QM_LVDS0_GPIO00_LSIO_GPIO1_IO04			0x00000021>;
> +	};
> +
> +	/* Apalis WAKE1_MICO */
> +	pinctrl_gpio_keys: gpiokeysgrp {
> +		fsl,pins = <IMX8QM_SPI3_CS0_LSIO_GPIO2_IO20			0x06700021>;
> +	};
> +
> +	/* Apalis USBH_OC# */
> +	pinctrl_gpio_usbh_oc_n: gpiousbhocngrp {
> +		fsl,pins = <IMX8QM_USB_SS3_TC3_LSIO_GPIO4_IO06			0x04000021>;
> +	};
> +
> +	/* On-module HDMI_CTRL */
> +	pinctrl_hdmi_ctrl: hdmictrlgrp {
> +		fsl,pins = <IMX8QM_MIPI_CSI1_GPIO0_00_LSIO_GPIO1_IO30		0x00000061>;
> +	};
> +
> +	/* On-module I2C */
> +	pinctrl_lpi2c1: lpi2c1grp {
> +		fsl,pins = <IMX8QM_GPT0_CLK_DMA_I2C1_SCL			0x04000020>,
> +			   <IMX8QM_GPT0_CAPTURE_DMA_I2C1_SDA			0x04000020>;
> +	};
> +
> +	/* Apalis I2C1 */
> +	pinctrl_lpi2c2: lpi2c2grp {
> +		fsl,pins = <IMX8QM_GPT1_CLK_DMA_I2C2_SCL			0x04000020>,
> +			   <IMX8QM_GPT1_CAPTURE_DMA_I2C2_SDA			0x04000020>;
> +	};
> +
> +	/* Apalis I2C3 (CAM) */
> +	pinctrl_lpi2c3: lpi2c3grp {
> +		fsl,pins = <IMX8QM_SIM0_PD_DMA_I2C3_SCL				0x04000020>,
> +			   <IMX8QM_SIM0_POWER_EN_DMA_I2C3_SDA			0x04000020>;
> +	};
> +
> +	/* Apalis SPI1 */
> +	pinctrl_lpspi0: lpspi0grp {
> +		fsl,pins = <IMX8QM_SPI0_SCK_DMA_SPI0_SCK			0x0600004c>,
> +			   <IMX8QM_SPI0_SDO_DMA_SPI0_SDO			0x0600004c>,
> +			   <IMX8QM_SPI0_SDI_DMA_SPI0_SDI			0x0600004c>,
> +			   <IMX8QM_SPI0_CS0_LSIO_GPIO3_IO05			0x0600004c>;
> +	};
> +
> +	/* Apalis SPI2 */
> +	pinctrl_lpspi2: lpspi2grp {
> +		fsl,pins = <IMX8QM_SPI2_SCK_DMA_SPI2_SCK			0x0600004c>,
> +			   <IMX8QM_SPI2_SDO_DMA_SPI2_SDO			0x0600004c>,
> +			   <IMX8QM_SPI2_SDI_DMA_SPI2_SDI			0x0600004c>,
> +			   <IMX8QM_SPI2_CS0_LSIO_GPIO3_IO10			0x0600004c>;
> +	};
> +
> +	/* Apalis UART3 */
> +	pinctrl_lpuart0: lpuart0grp {
> +		fsl,pins = <IMX8QM_UART0_RX_DMA_UART0_RX			0x06000020>,
> +			   <IMX8QM_UART0_TX_DMA_UART0_TX			0x06000020>;
> +	};
> +
> +	/* Apalis UART1 */
> +	pinctrl_lpuart1: lpuart1grp {
> +		fsl,pins = <IMX8QM_UART1_RX_DMA_UART1_RX			0x06000020>,
> +			   <IMX8QM_UART1_TX_DMA_UART1_TX			0x06000020>,
> +			   <IMX8QM_UART1_CTS_B_DMA_UART1_CTS_B			0x06000020>,
> +			   <IMX8QM_UART1_RTS_B_DMA_UART1_RTS_B			0x06000020>;
> +	};
> +
> +	/* Apalis UART1 */
> +	pinctrl_lpuart1ctrl: lpuart1ctrlgrp {
> +		fsl,pins = /* Apalis UART1_DTR */
> +			   <IMX8QM_M40_I2C0_SCL_LSIO_GPIO0_IO06			0x00000021>,
> +			   /* Apalis UART1_DSR */
> +			   <IMX8QM_M40_I2C0_SDA_LSIO_GPIO0_IO07			0x00000021>,
> +			   /* Apalis UART1_DCD */
> +			   <IMX8QM_M41_I2C0_SCL_LSIO_GPIO0_IO10			0x00000021>,
> +			   /* Apalis UART1_RI */
> +			   <IMX8QM_M41_I2C0_SDA_LSIO_GPIO0_IO11			0x00000021>;
> +	};
> +
> +	/* Apalis UART4 */
> +	pinctrl_lpuart2: lpuart2grp {
> +		fsl,pins = <IMX8QM_LVDS0_I2C1_SCL_DMA_UART2_TX			0x06000020>,
> +			   <IMX8QM_LVDS0_I2C1_SDA_DMA_UART2_RX			0x06000020>;
> +	};
> +
> +	/* Apalis UART2 */
> +	pinctrl_lpuart3: lpuart3grp {
> +		fsl,pins = <IMX8QM_LVDS1_I2C1_SCL_DMA_UART3_TX			0x06000020>,
> +			   <IMX8QM_LVDS1_I2C1_SDA_DMA_UART3_RX			0x06000020>,
> +			   <IMX8QM_ENET1_RGMII_TXD3_DMA_UART3_RTS_B		0x06000020>,
> +			   <IMX8QM_ENET1_RGMII_RXC_DMA_UART3_CTS_B		0x06000020>;
> +	};
> +
> +	/* Apalis TS_2 */
> +	pinctrl_lvds0_i2c0_gpio: lvds0i2c0gpiogrp {
> +		fsl,pins = <IMX8QM_LVDS0_I2C0_SCL_LSIO_GPIO1_IO06		0x00000021>;
> +	};
> +
> +	/* Apalis LCD1_G6+7 */
> +	pinctrl_lvds1_i2c0_gpios: lvds1i2c0gpiosgrp {
> +		fsl,pins = /* Apalis LCD1_G6 */
> +			   <IMX8QM_LVDS1_I2C0_SCL_LSIO_GPIO1_IO12		0x00000021>,
> +			   /* Apalis LCD1_G7 */
> +			   <IMX8QM_LVDS1_I2C0_SDA_LSIO_GPIO1_IO13		0x00000021>;
> +	};
> +
> +	/* Apalis TS_3 */
> +	pinctrl_mipi_dsi_0_1_en: mipidsi0-1engrp {
> +		fsl,pins = <IMX8QM_LVDS0_I2C0_SDA_LSIO_GPIO1_IO07		0x00000021>;
> +	};
> +
> +	/* Apalis TS_4 */
> +	pinctrl_mipi_dsi1_gpios: mipidsi1gpiosgrp {
> +		fsl,pins = <IMX8QM_MIPI_DSI1_GPIO0_00_LSIO_GPIO1_IO22		0x00000021>;
> +	};
> +
> +	/* Apalis TS_1 */
> +	pinctrl_mlb_gpios: mlbgpiosgrp {
> +		fsl,pins = <IMX8QM_MLB_CLK_LSIO_GPIO3_IO27			0x00000021>;
> +	};
> +
> +	/* Apalis MMC1_CD# */
> +	pinctrl_mmc1_cd: mmc1cdgrp {
> +		fsl,pins = <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09			0x00000021>;
> +	};
> +
> +	pinctrl_mmc1_cd_sleep: mmc1cdsleepgrp {
> +		fsl,pins = <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09			0x04000021>;
> +	};
> +
> +	/* On-module PCIe_Wi-Fi */
> +	pinctrl_pcieb: pciebgrp {
> +		fsl,pins = <IMX8QM_PCIE_CTRL1_CLKREQ_B_LSIO_GPIO4_IO30		0x00000021>,
> +			   <IMX8QM_PCIE_CTRL1_WAKE_B_LSIO_GPIO4_IO31		0x00000021>,
> +			   <IMX8QM_PCIE_CTRL1_PERST_B_LSIO_GPIO5_IO00		0x00000021>;
> +	};
> +
> +	/* On-module PCIe_CLK_EN1 */
> +	pinctrl_pcie_sata_refclk: pciesatarefclkgrp {
> +		fsl,pins = <IMX8QM_USDHC2_WP_LSIO_GPIO4_IO11			0x00000021>;
> +	};
> +
> +	/* On-module PCIe_CLK_EN2 */
> +	pinctrl_pcie_wifi_refclk: pciewifirefclkgrp {
> +		fsl,pins = <IMX8QM_ESAI1_TX3_RX2_LSIO_GPIO2_IO11		0x00000021>;
> +	};
> +
> +	/* Apalis PWM3 */
> +	pinctrl_pwm0: pwm0grp {
> +		fsl,pins = <IMX8QM_UART0_RTS_B_LSIO_PWM0_OUT			0x00000020>;
> +	};
> +
> +	/* Apalis PWM4 */
> +	pinctrl_pwm1: pwm1grp {
> +		fsl,pins = <IMX8QM_UART0_CTS_B_LSIO_PWM1_OUT			0x00000020>;
> +	};
> +
> +	/* Apalis PWM1 */
> +	pinctrl_pwm2: pwm2grp {
> +		fsl,pins = <IMX8QM_GPT1_COMPARE_LSIO_PWM2_OUT			0x00000020>;
> +	};
> +
> +	/* Apalis PWM2 */
> +	pinctrl_pwm3: pwm3grp {
> +		fsl,pins = <IMX8QM_GPT0_COMPARE_LSIO_PWM3_OUT			0x00000020>;
> +	};
> +
> +	/* Apalis BKL1_PWM */
> +	pinctrl_pwm_bkl: pwmbklgrp {
> +		fsl,pins = <IMX8QM_LVDS1_GPIO00_LVDS1_PWM0_OUT			0x00000020>;
> +	};
> +
> +	/* Apalis LCD1_ */
> +	pinctrl_qspi1a_gpios: qspi1agpiosgrp {
> +		fsl,pins = /* Apalis LCD1_B0 */
> +			   <IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26			0x00000021>,
> +			   /* Apalis LCD1_B1 */
> +			   <IMX8QM_QSPI1A_DATA1_LSIO_GPIO4_IO25			0x00000021>,
> +			   /* Apalis LCD1_B2 */
> +			   <IMX8QM_QSPI1A_DATA2_LSIO_GPIO4_IO24			0x00000021>,
> +			   /* Apalis LCD1_B3 */
> +			   <IMX8QM_QSPI1A_DATA3_LSIO_GPIO4_IO23			0x00000021>,
> +			   /* Apalis LCD1_B5 */
> +			   <IMX8QM_QSPI1A_DQS_LSIO_GPIO4_IO22			0x00000021>,
> +			   /* Apalis LCD1_B7 */
> +			   <IMX8QM_QSPI1A_SCLK_LSIO_GPIO4_IO21			0x00000021>,
> +			   /* Apalis LCD1_B4 */
> +			   <IMX8QM_QSPI1A_SS0_B_LSIO_GPIO4_IO19			0x00000021>,
> +			   /* Apalis LCD1_B6 */
> +			   <IMX8QM_QSPI1A_SS1_B_LSIO_GPIO4_IO20			0x00000021>;
> +	};
> +
> +	/* On-module RESET_MOCI#_DRV */
> +	pinctrl_reset_moci: resetmocigrp {
> +		fsl,pins = <IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30			0x00000021>;
> +	};
> +
> +	/* On-module I2S SGTL5000 for Apalis Analogue Audio */
> +	pinctrl_sai1: sai1grp {
> +		fsl,pins = <IMX8QM_SAI1_TXD_AUD_SAI1_TXD			0xc600006c>,
> +			   <IMX8QM_SAI1_RXD_AUD_SAI1_RXD			0xc600004c>,
> +			   <IMX8QM_SAI1_TXC_AUD_SAI1_TXC			0xc600004c>,
> +			   <IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS			0xc600004c>;
> +	};
> +
> +	/* Apalis SATA1_ACT# */
> +	pinctrl_sata1_act: sata1actgrp {
> +		fsl,pins = <IMX8QM_ESAI1_TX0_LSIO_GPIO2_IO08			0x00000021>;
> +	};
> +
> +	/* Apalis SD1_CD# */
> +	pinctrl_sd1_cd: sd1cdgrp {
> +		fsl,pins = <IMX8QM_USDHC2_CD_B_LSIO_GPIO4_IO12			0x00000021>;
> +	};
> +
> +	/* On-module I2S SGTL5000 SYS_MCLK */
> +	pinctrl_sgtl5000: sgtl5000grp {
> +		fsl,pins = <IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0			0xc600004c>;
> +	};
> +
> +	/* Apalis LCD1_ */
> +	pinctrl_sim0_gpios: sim0gpiosgrp {
> +		fsl,pins = /* Apalis LCD1_G5 */
> +			   <IMX8QM_SIM0_CLK_LSIO_GPIO0_IO00			0x00000021>,
> +			   /* Apalis LCD1_G3 */
> +			   <IMX8QM_SIM0_GPIO0_00_LSIO_GPIO0_IO05		0x00000021>,
> +			   /* Apalis TS_5 */
> +			   <IMX8QM_SIM0_IO_LSIO_GPIO0_IO02			0x00000021>,
> +			   /* Apalis LCD1_G4 */
> +			   <IMX8QM_SIM0_RST_LSIO_GPIO0_IO01			0x00000021>;
> +	};
> +
> +	/* Apalis SPDIF */
> +	pinctrl_spdif0: spdif0grp {
> +		fsl,pins = <IMX8QM_SPDIF0_TX_AUD_SPDIF0_TX			0xc6000040>,
> +			   <IMX8QM_SPDIF0_RX_AUD_SPDIF0_RX			0xc6000040>;
> +	};
> +
> +	pinctrl_touchctrl_gpios: touchctrlgpiosgrp {
> +		fsl,pins = <IMX8QM_ESAI1_FSR_LSIO_GPIO2_IO04			0x00000021>,
> +			   <IMX8QM_ESAI1_FST_LSIO_GPIO2_IO05			0x00000041>,
> +			   <IMX8QM_SPI3_SCK_LSIO_GPIO2_IO17			0x00000021>,
> +			   <IMX8QM_SPI3_CS1_LSIO_GPIO2_IO21			0x00000041>;
> +	};
> +
> +	pinctrl_touchctrl_idle: touchctrlidlegrp {
> +		fsl,pins = <IMX8QM_ADC_IN4_LSIO_GPIO3_IO22			0x00000021>,
> +			   <IMX8QM_ADC_IN5_LSIO_GPIO3_IO23			0x00000021>,
> +			   <IMX8QM_ADC_IN6_LSIO_GPIO3_IO24			0x00000021>,
> +			   <IMX8QM_ADC_IN7_LSIO_GPIO3_IO25			0x00000021>;
> +	};
> +
> +	/* On-module USB HSIC HUB (active) */
> +	pinctrl_usb_hsic_active: usbh1activegrp {
> +		fsl,pins = <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA		0x000000cf>,
> +			   <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE	0x000000ff>;
> +	};
> +
> +	/* On-module USB HSIC HUB (idle) */
> +	pinctrl_usb_hsic_idle: usbh1idlegrp {
> +		fsl,pins = <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA		0x000000cf>,
> +			   <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE	0x000000cf>;
> +	};
> +
> +	/* On-module USB HSIC HUB */
> +	pinctrl_usb3503a: usb3503agrp {
> +		fsl,pins = /* On-module HSIC_HUB_CONNECT */
> +			   <IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31			0x00000041>,
> +			   /* On-module HSIC_INT_N */
> +			   <IMX8QM_SCU_GPIO0_05_LSIO_GPIO1_IO01			0x00000021>,
> +			   /* On-module HSIC_RESET_N */
> +			   <IMX8QM_SCU_GPIO0_06_LSIO_GPIO1_IO02			0x00000041>;
> +	};
> +
> +	/* Apalis USBH_EN */
> +	pinctrl_usbh_en: usbhengrp {
> +		fsl,pins = <IMX8QM_USB_SS3_TC1_LSIO_GPIO4_IO04			0x00000021>;
> +	};
> +
> +	/* Apalis USBO1 */
> +	pinctrl_usbotg1: usbotg1grp {
> +		fsl,pins = /* Apalis USBO1_EN */
> +			   <IMX8QM_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021>,
> +			   /* Apalis USBO1_OC# */
> +			   <IMX8QM_USB_SS3_TC2_CONN_USB_OTG1_OC			0x04000021>;
> +	};
> +
> +	/* On-module eMMC */
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000041>,
> +			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000021>,
> +			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000021>,
> +			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000041>,
> +			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
> +		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000040>,
> +			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020>,
> +			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000040>,
> +			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000020>;
> +	};
> +
> +	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
> +		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000040>,
> +			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020>,
> +			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020>,
> +			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000040>,
> +			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000020>;
> +	};
> +
> +	/* Apalis TS_6 */
> +	pinctrl_usdhc1_gpios: usdhc1gpiosgrp {
> +		fsl,pins = <IMX8QM_USDHC1_STROBE_LSIO_GPIO5_IO23		0x00000021>;
> +	};
> +
> +	/* Apalis MMC1 */
> +	pinctrl_usdhc2_4bit: usdhc2grp4bitgrp {
> +		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000041>,
> +			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000021>,
> +			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000021>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc2_4bit_100mhz: usdhc2-4bit100mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040>,
> +			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020>,
> +			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000020>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc2_4bit_200mhz: usdhc2-4bit200mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040>,
> +			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020>,
> +			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000020>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc2_8bit: usdhc2grp8bitgrp {
> +		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000021>,
> +			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc2_8bit_100mhz: usdhc2-8bit100mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000020>;
> +	};
> +
> +	pinctrl_usdhc2_8bit_200mhz: usdhc2-8bit200mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000020>,
> +			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000020>;
> +	};
> +
> +	pinctrl_usdhc2_4bit_sleep: usdhc2-4bitsleepgrp {
> +		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x04000061>,
> +			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x04000061>,
> +			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x04000061>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc2_8bit_sleep: usdhc2-8bitsleepgrp {
> +		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x04000061>,
> +			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x04000061>;
> +	};
> +
> +	/* Apalis SD1 */
> +	pinctrl_usdhc3: usdhc3grp {
> +		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
> +			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
> +			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
> +			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
> +			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
> +	};
> +
> +	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> +		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
> +			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
> +			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
> +			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
> +			   /* On-module PMIC use */
> +			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
> +	};
> +
> +	/* On-module Wi-Fi */
> +	pinctrl_wifi: wifigrp {
> +		fsl,pins = /* On-module Wi-Fi_SUSCLK_32k */
> +			   <IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K	0x06000021>,
> +			   /* On-module Wi-Fi_PCIE_W_DISABLE */
> +			   <IMX8QM_MIPI_CSI0_MCLK_OUT_LSIO_GPIO1_IO24		0x06000021>;
> +	};
> +
> +	pinctrl_wifi_pdn: wifipdngrp {
> +		fsl,pins = /* On-module Wi-Fi_POWER_DOWN */
> +			   <IMX8QM_MIPI_CSI0_GPIO0_01_LSIO_GPIO1_IO28		0x06000021>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
> new file mode 100644
> index 000000000000..81ba8b2831ac
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2022 Toradex
> + */
> +
> +#include <dt-bindings/pwm/pwm.h>
> +#include "imx8qm.dtsi"
> +#include "imx8-apalis-v1.1.dtsi"
> +
> +/ {
> +	model = "Toradex Apalis iMX8QM V1.1";
> +	compatible = "toradex,apalis-imx8-v1.1",
> +		     "fsl,imx8qm";
> +};
> +
> +/* TODO: Cooling Maps */
> diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi
> new file mode 100644
> index 000000000000..1c6af9f549a8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi
> @@ -0,0 +1,340 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2022 Toradex
> + */
> +
> +#include "imx8qm-apalis-v1.1.dtsi"
> +
> +/ {
> +	model = "Toradex Apalis iMX8QM";
> +	compatible = "toradex,apalis-imx8",
> +		     "fsl,imx8qm";
> +};
> +
> +&ethphy0 {
> +	interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> +};
> +
> +/*
> + * Apalis iMX8QM V1.0 has PHY KSZ9031. the Micrel PHY driver
> + * doesn't support setting internal PHY delay for TXC line for
> + * this PHY model. Use delay on MAC side instead.
> + */
> +&fec1 {
> +	fsl,rgmii_txc_dly;
> +	phy-mode = "rgmii-rxid";
> +};
> +
> +/* TODO: Apalis HDMI1 */
> +
> +/* Apalis I2C2 (DDC) */
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpi2c0>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	clock-frequency = <100000>;
> +};
> +
> +&lsio_gpio0 {
> +	gpio-line-names = "MXM3_279",
> +			  "MXM3_277",
> +			  "MXM3_135",
> +			  "MXM3_203",
> +			  "MXM3_201",
> +			  "MXM3_275",
> +			  "MXM3_110",
> +			  "MXM3_120",
> +			  "MXM3_1/GPIO1",
> +			  "MXM3_3/GPIO2",
> +			  "MXM3_124",
> +			  "MXM3_122",
> +			  "MXM3_5/GPIO3",
> +			  "MXM3_7/GPIO4",
> +			  "",
> +			  "",
> +			  "MXM3_4",
> +			  "MXM3_211",
> +			  "MXM3_209",
> +			  "MXM3_2",
> +			  "MXM3_136",
> +			  "MXM3_134",
> +			  "MXM3_6",
> +			  "MXM3_8",
> +			  "MXM3_112",
> +			  "MXM3_118",
> +			  "MXM3_114",
> +			  "MXM3_116";
> +};
> +
> +&lsio_gpio1 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_286",
> +			  "",
> +			  "MXM3_87",
> +			  "MXM3_99",
> +			  "MXM3_138",
> +			  "MXM3_140",
> +			  "MXM3_239",
> +			  "",
> +			  "MXM3_281",
> +			  "MXM3_283",
> +			  "MXM3_126",
> +			  "MXM3_132",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_173",
> +			  "MXM3_175",
> +			  "MXM3_123";
> +};
> +
> +&lsio_gpio2 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_198",
> +			  "MXM3_35",
> +			  "MXM3_164",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_217",
> +			  "MXM3_215",
> +			  "",
> +			  "",
> +			  "MXM3_193",
> +			  "MXM3_194",
> +			  "MXM3_37",
> +			  "",
> +			  "MXM3_271",
> +			  "MXM3_273",
> +			  "MXM3_195",
> +			  "MXM3_197",
> +			  "MXM3_177",
> +			  "MXM3_179",
> +			  "MXM3_181",
> +			  "MXM3_183",
> +			  "MXM3_185",
> +			  "MXM3_187";
> +};
> +
> +&lsio_gpio3 {
> +	gpio-line-names = "MXM3_191",
> +			  "",
> +			  "MXM3_221",
> +			  "MXM3_225",
> +			  "MXM3_223",
> +			  "MXM3_227",
> +			  "MXM3_200",
> +			  "MXM3_235",
> +			  "MXM3_231",
> +			  "MXM3_229",
> +			  "MXM3_233",
> +			  "MXM3_204",
> +			  "MXM3_196",
> +			  "",
> +			  "MXM3_202",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_305",
> +			  "MXM3_307",
> +			  "MXM3_309",
> +			  "MXM3_311",
> +			  "MXM3_315",
> +			  "MXM3_317",
> +			  "MXM3_319",
> +			  "MXM3_321",
> +			  "MXM3_15/GPIO7",
> +			  "MXM3_63",
> +			  "MXM3_17/GPIO8",
> +			  "MXM3_12",
> +			  "MXM3_14",
> +			  "MXM3_16";
> +};
> +
> +&lsio_gpio4 {
> +	gpio-line-names = "MXM3_18",
> +			  "MXM3_11/GPIO5",
> +			  "MXM3_13/GPIO6",
> +			  "MXM3_274",
> +			  "MXM3_84",
> +			  "MXM3_262",
> +			  "MXM3_96",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_190",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_269",
> +			  "MXM3_251",
> +			  "MXM3_253",
> +			  "MXM3_295",
> +			  "MXM3_299",
> +			  "MXM3_301",
> +			  "MXM3_297",
> +			  "MXM3_293",
> +			  "MXM3_291",
> +			  "MXM3_289",
> +			  "MXM3_287";
> +
> +	/* Enable pcie root / sata ref clock unconditionally */
> +	pcie-sata-hog {
> +		gpios = <27 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +};
> +
> +&lsio_gpio5 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_150",
> +			  "MXM3_160",
> +			  "MXM3_162",
> +			  "MXM3_144",
> +			  "MXM3_146",
> +			  "MXM3_148",
> +			  "MXM3_152",
> +			  "MXM3_156",
> +			  "MXM3_158",
> +			  "MXM3_159",
> +			  "MXM3_184",
> +			  "MXM3_180",
> +			  "MXM3_186",
> +			  "MXM3_188",
> +			  "MXM3_176",
> +			  "MXM3_178";
> +};
> +
> +&lsio_gpio6 {
> +	gpio-line-names = "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "",
> +			  "MXM3_261",
> +			  "MXM3_263",
> +			  "MXM3_259",
> +			  "MXM3_257",
> +			  "MXM3_255",
> +			  "MXM3_128",
> +			  "MXM3_130",
> +			  "MXM3_265",
> +			  "MXM3_249",
> +			  "MXM3_247",
> +			  "MXM3_245",
> +			  "MXM3_243";
> +};
> +
> +&pinctrl_fec1 {
> +	fsl,pins =
> +		/* Use pads in 1.8V mode */
> +		<IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
> +		<IMX8QM_ENET0_MDC_CONN_ENET0_MDC				0x06000020>,
> +		<IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO				0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL		0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL		0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2			0x06000020>,
> +		<IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3			0x06000020>,
> +		<IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M	0x06000020>,
> +		/* On-module ETH_RESET# */
> +		<IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x06000020>,
> +		/* On-module ETH_INT# */
> +		<IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05				0x04000060>;
> +};
> +
> +&pinctrl_fec1_sleep {
> +	fsl,pins =
> +		<IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
> +		<IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14				0x04000040>,
> +		<IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13				0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30				0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04				0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08			0x04000040>,
> +		<IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09			0x04000040>,
> +		<IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15			0x04000040>,
> +		<IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x04000040>,
> +		<IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05				0x04000040>;
> +};
> +
> +&iomuxc {
> +	/* Apalis I2C2 (DDC) */
> +	pinctrl_lpi2c0: lpi2c0grp {
> +		fsl,pins =
> +			<IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL			0x04000022>,
> +			<IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA			0x04000022>;
> +	};
> +};
> +
> +/* On-module PCIe_CTRL0_CLKREQ */
> +&pinctrl_pcie_sata_refclk {
> +	fsl,pins =
> +		<IMX8QM_PCIE_CTRL0_CLKREQ_B_LSIO_GPIO4_IO27			0x00000021>;
> +};
> +
> +/* TODO: On-module Wi-Fi */
> +
> +/* Apalis MMC1 */
> +&usdhc2 {
> +	/*
> +	 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
> +	 * issues with certain SD cards, disable 1.8V signaling for now.
> +	 */
> +	no-1-8-v;
> +};
> +
> +/* Apalis SD1 */
> +&usdhc3 {
> +	/*
> +	 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
> +	 * issues with certain SD cards, disable 1.8V signaling for now.
> +	 */
> +	no-1-8-v;
> +};
> -- 
> 2.36.1
>
Marcel Ziswiler Feb. 3, 2023, 1:14 p.m. UTC | #2
Hi Shawn

On Wed, 2023-02-01 at 04:01 +0100, Marcel Ziswiler wrote:

[snip]


> > > +/* Apalis UART1 */
> > > +&lpuart1 {
> > > +       dma-names = "","";
> > 
> > What is this for?
> 
> I guess that switches off DMA falling pack to PIO. Likely, there was an issue at one point in downstream. Let
> me re-test without it.

BTW: Upstream this indeed works just fine without this and I removed it in v6.

[snip]

> > > +&usbotg1 {
> > > +       adp-disable;
> > > +       ci-disable-lpm;
> > > +       hnp-disable;
> > > +       over-current-active-low;
> > > +       pinctrl-names = "default";
> > > +       pinctrl-0 = <&pinctrl_usbotg1>;
> > 
> > We generally want to put such generic properties before device specific
> > ones.
> 
> Okay.

Sorry, I missed the generally here. Let me re-work the device trees with this in mind adhering to hopefully all
the rules which apply and send a v7 ASAP.

> Thanks!

Thank you!

> > Shawn

Cheers

Marcel


[snip]
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi b/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
new file mode 100644
index 000000000000..3960ef30464e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-apalis-v1.1.dtsi
@@ -0,0 +1,1453 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	/* Apalis BKL1 */
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&lsio_gpio1 4 GPIO_ACTIVE_HIGH>; /* Apalis BKL1_ON */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_bkl_on>;
+		/* TODO: hook-up to Apalis BKL1_PWM */
+		status = "disabled";
+	};
+
+	gpio_fan: gpio-fan {
+		compatible = "gpio-fan";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio8>;
+		gpios = <&lsio_gpio3 28 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <	 0 0
+				      3000 1>;
+	};
+
+/* TODO: LVDS Panel */
+
+/* TODO: Shared PCIe/SATA Reference Clock */
+
+/* TODO: PCIe Wi-Fi Reference Clock */
+
+	/*
+	 * Power management bus used to control LDO1OUT of the
+	 * second PMIC PF8100. This is used for controlling voltage levels of
+	 * typespecific RGMII signals and Apalis UART2_RTS UART2_CTS.
+	 *
+	 * IMX_SC_R_BOARD_R1 for 3.3V
+	 * IMX_SC_R_BOARD_R2 for 1.8V
+	 * IMX_SC_R_BOARD_R3 for 2.5V
+	 * Note that for 2.5V operation the pad muxing needs to be changed,
+	 * compare with PSW_OVR field of IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD.
+	 *
+	 * those power domains are mutually exclusive.
+	 */
+	reg_ext_rgmii: regulator-ext-rgmii {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_EXT_RGMII (LDO1)";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		power-domains = <&pd IMX_SC_R_BOARD_R1>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_wifi: regulator-module-wifi {
+		compatible = "regulator-fixed";
+		gpio = <&lsio_gpio1 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pdn>;
+		regulator-name = "wifi_pwrdn_fake_regulator";
+		regulator-settling-time-us = <100>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	reg_pcie_switch: regulator-pcie-switch {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio7>;
+		gpio = <&lsio_gpio3 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "pcie_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		startup-delay-us = <100000>;
+	};
+
+	reg_usb_host_vbus: regulator-usb-host-vbus {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usbh_en>;
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			/* Apalis USBH_EN */
+			gpio = <&lsio_gpio4 4 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			regulator-always-on;
+	};
+
+	reg_usb_hsic: regulator-usb-hsic {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-hsic-dummy";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+	};
+
+	reg_usb_phy: regulator-usb-hsic1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-phy-dummy";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		decoder_boot: decoder_boot@84000000 {
+			no-map;
+			reg = <0 0x84000000 0 0x2000000>;
+		};
+
+		encoder1_boot: encoder1_boot@86000000 {
+			no-map;
+			reg = <0 0x86000000 0 0x200000>;
+		};
+
+		encoder2_boot: encoder2_boot@86200000 {
+			no-map;
+			reg = <0 0x86200000 0 0x200000>;
+		};
+
+		/*
+		 * reserved-memory layout
+		 * 0x8800_0000 ~ 0x8FFF_FFFF is reserved for M4
+		 * Shouldn't be used at A core and Linux side.
+		 *
+		 */
+		m4_reserved: m4@88000000 {
+			no-map;
+			reg = <0 0x88000000 0 0x8000000>;
+		};
+
+		rpmsg_reserved: rpmsg@90000000 {
+			no-map;
+			reg = <0 0x90200000 0 0x200000>;
+		};
+
+		vdevbuffer: vdevbuffer@90400000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x90400000 0 0x100000>;
+			no-map;
+		};
+
+		decoder_rpc: decoder_rpc@92000000 {
+			no-map;
+			reg = <0 0x92000000 0 0x200000>;
+		};
+
+		dsp_reserved: dsp@92400000 {
+			no-map;
+			reg = <0 0x92400000 0 0x2000000>;
+		};
+
+		encoder1_rpc: encoder1_rpc@94400000 {
+			no-map;
+			reg = <0 0x94400000 0 0x700000>;
+		};
+
+		encoder2_rpc: encoder2_rpc@94b00000 {
+			no-map;
+			reg = <0 0x94b00000 0 0x700000>;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x3c000000>;
+			alloc-ranges = <0 0xc0000000 0 0x3c000000>;
+			linux,cma-default;
+		};
+	};
+
+	/* TODO: Apalis Analogue Audio */
+
+	/* TODO: HDMI Audio */
+
+	/* TODO: Apalis SPDIF1 */
+
+	touchscreen: vf50-touchscreen {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 2>,<&adc1 1>,
+			      <&adc1 0>,<&adc1 3>;
+		interrupt-parent = <&lsio_gpio3>;
+		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>, <&pinctrl_touchctrl_gpios>;
+		pinctrl-1 = <&pinctrl_adc1>, <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		xp-gpios = <&lsio_gpio2 4 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&lsio_gpio2 5 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&lsio_gpio2 17 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&lsio_gpio2 21 GPIO_ACTIVE_HIGH>;
+		/*
+		 * NOTE: you must remove the pinctrl-adc1 from the adc1
+		 * node below to use the touchscreen
+		 */
+		status = "disabled";
+	};
+
+};
+
+&adc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0>;
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+};
+
+/* TODO: Asynchronous Sample Rate Converter (ASRC) */
+
+/* Apalis ETH1 */
+&fec1 {
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-1 = <&pinctrl_fec1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&lsio_gpio1>;
+			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+			reset-assert-us = <2>;
+			reset-deassert-us = <2>;
+			reset-gpios = <&lsio_gpio1 11 GPIO_ACTIVE_LOW>;
+			reset-names = "phy-reset";
+		};
+	};
+};
+
+/* Apalis CAN1 */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+};
+
+/* Apalis CAN2 */
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+/* Apalis CAN3 (optional) */
+&flexcan3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan3>;
+};
+
+/* TODO: Apalis HDMI1 */
+
+/* On-module I2C */
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	/* TODO: Audio Codec */
+
+	/* USB3503A */
+	usb3503@8 {
+		compatible = "smsc,usb3503a";
+		connect-gpios = <&lsio_gpio0 31 GPIO_ACTIVE_LOW>;
+		initial-mode = <1>;
+		intn-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb3503a>;
+		refclk-frequency = <25000000>;
+		reg = <0x08>;
+		reset-gpios = <&lsio_gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* Apalis I2C1 */
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c2>;
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		interrupt-parent = <&lsio_gpio4>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;		/* Apalis GPIO5 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio5>, <&pinctrl_gpio6>;
+		reset-gpios = <&lsio_gpio4 2 GPIO_ACTIVE_LOW>;	/* Apalis GPIO6 */
+		status = "disabled";
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+		status = "disabled";
+	};
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+};
+
+&jpegdec {
+	status = "okay";
+};
+
+&jpegenc {
+	status = "okay";
+};
+
+/* TODO: Apalis LVDS1 */
+
+/* Apalis SPI1 */
+&lpspi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&lsio_gpio3 5 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi0>;
+};
+
+/* Apalis SPI2 */
+&lpspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&lsio_gpio3 10 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi2>;
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+	dma-names = "","";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+	dma-names = "","";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart2>;
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart3>;
+};
+
+&lsio_gpio0 {
+	gpio-line-names = "MXM3_279",
+			  "MXM3_277",
+			  "MXM3_135",
+			  "MXM3_203",
+			  "MXM3_201",
+			  "MXM3_275",
+			  "MXM3_110",
+			  "MXM3_120",
+			  "MXM3_1/GPIO1",
+			  "MXM3_3/GPIO2",
+			  "MXM3_124",
+			  "MXM3_122",
+			  "MXM3_5/GPIO3",
+			  "MXM3_7/GPIO4",
+			  "",
+			  "",
+			  "MXM3_4",
+			  "MXM3_211",
+			  "MXM3_209",
+			  "MXM3_2",
+			  "MXM3_136",
+			  "MXM3_134",
+			  "MXM3_6",
+			  "MXM3_8",
+			  "MXM3_112",
+			  "MXM3_118",
+			  "MXM3_114",
+			  "MXM3_116";
+};
+
+&lsio_gpio1 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_286",
+			  "",
+			  "MXM3_87",
+			  "MXM3_99",
+			  "MXM3_138",
+			  "MXM3_140",
+			  "MXM3_239",
+			  "",
+			  "MXM3_281",
+			  "MXM3_283",
+			  "MXM3_126",
+			  "MXM3_132",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_173",
+			  "MXM3_175",
+			  "MXM3_123";
+
+	hdmi-ctrl-hog {
+		gpio-hog;
+		gpios = <30 GPIO_ACTIVE_HIGH>;
+		line-name = "CONNECTOR_IS_HDMI";
+		/* Set signals depending on HDP device type, 0 DP, 1 HDMI */
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hdmi_ctrl>;
+	};
+};
+
+&lsio_gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_198",
+			  "MXM3_35",
+			  "MXM3_164",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_217",
+			  "MXM3_215",
+			  "",
+			  "",
+			  "MXM3_193",
+			  "MXM3_194",
+			  "MXM3_37",
+			  "",
+			  "MXM3_271",
+			  "MXM3_273",
+			  "MXM3_195",
+			  "MXM3_197",
+			  "MXM3_177",
+			  "MXM3_179",
+			  "MXM3_181",
+			  "MXM3_183",
+			  "MXM3_185",
+			  "MXM3_187";
+
+	/*
+	 * Add GPIO2_20 as a wakeup source:
+	 * Pin:  101	SC_P_SPI3_CS0 (MXM3_37/WAKE1_MICO)
+	 * Type: 5	SC_PAD_WAKEUP_FALL_EDGE
+	 * Line: 20
+	 */
+	 pad-wakeup = <IMX8QM_SPI3_CS0 5 20>;
+	 pad-wakeup-num = <1>;
+
+	pcie-wifi-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		line-name = "PCIE_WIFI_CLK";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_wifi_refclk>;
+	};
+};
+
+&lsio_gpio3 {
+	gpio-line-names = "MXM3_191",
+			  "",
+			  "MXM3_221",
+			  "MXM3_225",
+			  "MXM3_223",
+			  "MXM3_227",
+			  "MXM3_200",
+			  "MXM3_235",
+			  "MXM3_231",
+			  "MXM3_229",
+			  "MXM3_233",
+			  "MXM3_204",
+			  "MXM3_196",
+			  "",
+			  "MXM3_202",
+			  "",
+			  "",
+			  "",
+			  "MXM3_305",
+			  "MXM3_307",
+			  "MXM3_309",
+			  "MXM3_311",
+			  "MXM3_315",
+			  "MXM3_317",
+			  "MXM3_319",
+			  "MXM3_321",
+			  "MXM3_15/GPIO7",
+			  "MXM3_63",
+			  "MXM3_17/GPIO8",
+			  "MXM3_12",
+			  "MXM3_14",
+			  "MXM3_16";
+};
+
+&lsio_gpio4 {
+	gpio-line-names = "MXM3_18",
+			  "MXM3_11/GPIO5",
+			  "MXM3_13/GPIO6",
+			  "MXM3_274",
+			  "MXM3_84",
+			  "MXM3_262",
+			  "MXM3_96",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_190",
+			  "",
+			  "",
+			  "",
+			  "MXM3_269",
+			  "MXM3_251",
+			  "MXM3_253",
+			  "MXM3_295",
+			  "MXM3_299",
+			  "MXM3_301",
+			  "MXM3_297",
+			  "MXM3_293",
+			  "MXM3_291",
+			  "MXM3_289",
+			  "MXM3_287";
+
+	/* Enable pcie root / sata ref clock unconditionally */
+	pcie-sata-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>;
+		line-name = "PCIE_SATA_CLK";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_sata_refclk>;
+	};
+};
+
+&lsio_gpio5 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_150",
+			  "MXM3_160",
+			  "MXM3_162",
+			  "MXM3_144",
+			  "MXM3_146",
+			  "MXM3_148",
+			  "MXM3_152",
+			  "MXM3_156",
+			  "MXM3_158",
+			  "MXM3_159",
+			  "MXM3_184",
+			  "MXM3_180",
+			  "MXM3_186",
+			  "MXM3_188",
+			  "MXM3_176",
+			  "MXM3_178";
+};
+
+&lsio_gpio6 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_261",
+			  "MXM3_263",
+			  "MXM3_259",
+			  "MXM3_257",
+			  "MXM3_255",
+			  "MXM3_128",
+			  "MXM3_130",
+			  "MXM3_265",
+			  "MXM3_249",
+			  "MXM3_247",
+			  "MXM3_245",
+			  "MXM3_243";
+};
+
+/* Apalis PWM3, MXM3 pin 6 */
+&lsio_pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0>;
+	#pwm-cells = <3>;
+};
+
+/* Apalis PWM4, MXM3 pin 8 */
+&lsio_pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	#pwm-cells = <3>;
+};
+
+/* Apalis PWM1, MXM3 pin 2 */
+&lsio_pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	#pwm-cells = <3>;
+};
+
+/* Apalis PWM2, MXM3 pin 4 */
+&lsio_pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	#pwm-cells = <3>;
+};
+
+/* TODO: Messaging Units */
+
+/* TODO: Apalis PCIE1 */
+
+/* TODO: On-module Wi-Fi */
+
+/* TODO: Apalis BKL1_PWM */
+
+/* TODO: Apalis DAP1 */
+
+/* TODO: Analogue Audio */
+
+/* TODO: Apalis SATA1 */
+
+/* TODO: Apalis SPDIF1 */
+
+/* TODO: Thermal Zones */
+
+/* TODO: Apalis USBH2, Apalis USBH3 and on-module Wi-Fi via on-module HSIC Hub */
+
+/* TODO: Apalis USBH4 */
+
+/* Apalis USBO1 */
+&usbphy1 {
+	phy-3p0-supply = <&reg_usb_phy>;
+	status = "okay";
+};
+
+&usbotg1 {
+	adp-disable;
+	ci-disable-lpm;
+	hnp-disable;
+	over-current-active-low;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	power-active-high;
+	srp-disable;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	status = "okay";
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+	bus-width = <8>;
+	cd-gpios = <&lsio_gpio2 9 GPIO_ACTIVE_LOW>; /* Apalis MMC1_CD# */
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2_4bit>,
+		    <&pinctrl_usdhc2_8bit>,
+		    <&pinctrl_mmc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>,
+		    <&pinctrl_usdhc2_8bit_100mhz>,
+		    <&pinctrl_mmc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>,
+		    <&pinctrl_usdhc2_8bit_200mhz>,
+		    <&pinctrl_mmc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>,
+		    <&pinctrl_usdhc2_8bit_sleep>,
+		    <&pinctrl_mmc1_cd_sleep>;
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	bus-width = <4>;
+	cd-gpios = <&lsio_gpio4 12 GPIO_ACTIVE_LOW>; /* Apalis SD1_CD# */
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_sd1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_sd1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_sd1_cd>;
+};
+
+/* TODO: Video Processing Unit (driver upstream but device tree part missing) */
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
+		    <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>, <&pinctrl_gpio_keys>,
+		    <&pinctrl_gpio_usbh_oc_n>, <&pinctrl_lpuart1ctrl>,
+		    <&pinctrl_lvds0_i2c0_gpio>, <&pinctrl_lvds1_i2c0_gpios>,
+		    <&pinctrl_mipi_dsi_0_1_en>, <&pinctrl_mipi_dsi1_gpios>,
+		    <&pinctrl_mlb_gpios>, <&pinctrl_qspi1a_gpios>,
+		    <&pinctrl_sata1_act>, <&pinctrl_sim0_gpios>,
+		    <&pinctrl_usdhc1_gpios>;
+
+	/* Apalis AN1_ADC */
+	pinctrl_adc0: adc0grp {
+		fsl,pins = /* Apalis AN1_ADC0 */
+			   <IMX8QM_ADC_IN0_DMA_ADC0_IN0				0xc0000060>,
+			   /* Apalis AN1_ADC1 */
+			   <IMX8QM_ADC_IN1_DMA_ADC0_IN1				0xc0000060>,
+			   /* Apalis AN1_ADC2 */
+			   <IMX8QM_ADC_IN2_DMA_ADC0_IN2				0xc0000060>,
+			   /* Apalis AN1_TSWIP_ADC3 */
+			   <IMX8QM_ADC_IN3_DMA_ADC0_IN3				0xc0000060>;
+	};
+
+	/* Apalis AN1_TS */
+	pinctrl_adc1: adc1grp {
+		fsl,pins = /* Apalis AN1_TSPX */
+			   <IMX8QM_ADC_IN4_DMA_ADC1_IN0				0xc0000060>,
+			   /* Apalis AN1_TSMX */
+			   <IMX8QM_ADC_IN5_DMA_ADC1_IN1				0xc0000060>,
+			   /* Apalis AN1_TSPY */
+			   <IMX8QM_ADC_IN6_DMA_ADC1_IN2				0xc0000060>,
+			   /* Apalis AN1_TSMY */
+			   <IMX8QM_ADC_IN7_DMA_ADC1_IN3				0xc0000060>;
+	};
+
+	/* Apalis CAM1 */
+	pinctrl_cam1_gpios: cam1gpiosgrp {
+		fsl,pins = /* Apalis CAM1_D7 */
+			   <IMX8QM_MIPI_DSI1_I2C0_SCL_LSIO_GPIO1_IO20		0x00000021>,
+			   /* Apalis CAM1_D6 */
+			   <IMX8QM_MIPI_DSI1_I2C0_SDA_LSIO_GPIO1_IO21		0x00000021>,
+			   /* Apalis CAM1_D5 */
+			   <IMX8QM_ESAI0_TX0_LSIO_GPIO2_IO26			0x00000021>,
+			   /* Apalis CAM1_D4 */
+			   <IMX8QM_ESAI0_TX1_LSIO_GPIO2_IO27			0x00000021>,
+			   /* Apalis CAM1_D3 */
+			   <IMX8QM_ESAI0_TX2_RX3_LSIO_GPIO2_IO28		0x00000021>,
+			   /* Apalis CAM1_D2 */
+			   <IMX8QM_ESAI0_TX3_RX2_LSIO_GPIO2_IO29		0x00000021>,
+			   /* Apalis CAM1_D1 */
+			   <IMX8QM_ESAI0_TX4_RX1_LSIO_GPIO2_IO30		0x00000021>,
+			   /* Apalis CAM1_D0 */
+			   <IMX8QM_ESAI0_TX5_RX0_LSIO_GPIO2_IO31		0x00000021>,
+			   /* Apalis CAM1_PCLK */
+			   <IMX8QM_MCLK_IN0_LSIO_GPIO3_IO00			0x00000021>,
+			   /* Apalis CAM1_MCLK */
+			   <IMX8QM_SPI3_SDO_LSIO_GPIO2_IO18			0x00000021>,
+			   /* Apalis CAM1_VSYNC */
+			   <IMX8QM_ESAI0_SCKR_LSIO_GPIO2_IO24			0x00000021>,
+			   /* Apalis CAM1_HSYNC */
+			   <IMX8QM_ESAI0_SCKT_LSIO_GPIO2_IO25			0x00000021>;
+	};
+
+	/* Apalis DAP1 */
+	pinctrl_dap1_gpios: dap1gpiosgrp {
+		fsl,pins = /* Apalis DAP1_MCLK */
+			   <IMX8QM_SPI3_SDI_LSIO_GPIO2_IO19			0x00000021>,
+			   /* Apalis DAP1_D_OUT */
+			   <IMX8QM_SAI1_RXC_LSIO_GPIO3_IO12			0x00000021>,
+			   /* Apalis DAP1_RESET */
+			   <IMX8QM_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000021>,
+			   /* Apalis DAP1_BIT_CLK */
+			   <IMX8QM_SPI0_CS1_LSIO_GPIO3_IO06			0x00000021>,
+			   /* Apalis DAP1_D_IN */
+			   <IMX8QM_SAI1_RXFS_LSIO_GPIO3_IO14			0x00000021>,
+			   /* Apalis DAP1_SYNC */
+			   <IMX8QM_SPI2_CS1_LSIO_GPIO3_IO11			0x00000021>,
+			   /* On-module Wi-Fi_I2S_EN# */
+			   <IMX8QM_ESAI1_TX5_RX0_LSIO_GPIO2_IO13		0x00000021>;
+	};
+
+	/* Apalis LCD1_G1+2 */
+	pinctrl_esai0_gpios: esai0gpiosgrp {
+		fsl,pins = /* Apalis LCD1_G1 */
+			   <IMX8QM_ESAI0_FSR_LSIO_GPIO2_IO22			0x00000021>,
+			   /* Apalis LCD1_G2 */
+			   <IMX8QM_ESAI0_FST_LSIO_GPIO2_IO23			0x00000021>;
+	};
+
+	/* On-module Gigabit Ethernet PHY Micrel KSZ9031 for Apalis GLAN */
+	pinctrl_fec1: fec1grp {
+		fsl,pins = /* Use pads in 3.3V mode */
+			   <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
+			   <IMX8QM_ENET0_MDC_CONN_ENET0_MDC				0x06000020>,
+			   <IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO				0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC			0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC			0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x06000020>,
+			   <IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x06000020>,
+			   <IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M	0x06000020>,
+			   /* On-module ETH_RESET# */
+			   <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x06000020>,
+			   /* On-module ETH_INT# */
+			   <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29			0x04000060>;
+	};
+
+	pinctrl_fec1_sleep: fec1-sleepgrp {
+		fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD		0x000014a0>,
+			   <IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14			0x04000040>,
+			   <IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13			0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08		0x04000040>,
+			   <IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09		0x04000040>,
+			   <IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15	0x04000040>,
+			   <IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11			0x06000020>,
+			   <IMX8QM_MIPI_CSI1_MCLK_OUT_LSIO_GPIO1_IO29		0x04000040>;
+	};
+
+	/* Apalis LCD1_ */
+	pinctrl_fec2_gpios: fec2gpiosgrp {
+		fsl,pins = <IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD		0x000014a0>,
+			   /* Apalis LCD1_R1 */
+			   <IMX8QM_ENET1_MDC_LSIO_GPIO4_IO18			0x00000021>,
+			   /* Apalis LCD1_R0 */
+			   <IMX8QM_ENET1_MDIO_LSIO_GPIO4_IO17			0x00000021>,
+			   /* Apalis LCD1_G0 */
+			   <IMX8QM_ENET1_REFCLK_125M_25M_LSIO_GPIO4_IO16	0x00000021>,
+			   /* Apalis LCD1_R7 */
+			   <IMX8QM_ENET1_RGMII_RX_CTL_LSIO_GPIO6_IO17		0x00000021>,
+			   /* Apalis LCD1_DE */
+			   <IMX8QM_ENET1_RGMII_RXD0_LSIO_GPIO6_IO18		0x00000021>,
+			   /* Apalis LCD1_HSYNC */
+			   <IMX8QM_ENET1_RGMII_RXD1_LSIO_GPIO6_IO19		0x00000021>,
+			   /* Apalis LCD1_VSYNC */
+			   <IMX8QM_ENET1_RGMII_RXD2_LSIO_GPIO6_IO20		0x00000021>,
+			   /* Apalis LCD1_PCLK */
+			   <IMX8QM_ENET1_RGMII_RXD3_LSIO_GPIO6_IO21		0x00000021>,
+			   /* Apalis LCD1_R6 */
+			   <IMX8QM_ENET1_RGMII_TX_CTL_LSIO_GPIO6_IO11		0x00000021>,
+			   /* Apalis LCD1_R5 */
+			   <IMX8QM_ENET1_RGMII_TXC_LSIO_GPIO6_IO10		0x00000021>,
+			   /* Apalis LCD1_R4 */
+			   <IMX8QM_ENET1_RGMII_TXD0_LSIO_GPIO6_IO12		0x00000021>,
+			   /* Apalis LCD1_R3 */
+			   <IMX8QM_ENET1_RGMII_TXD1_LSIO_GPIO6_IO13		0x00000021>,
+			   /* Apalis LCD1_R2 */
+			   <IMX8QM_ENET1_RGMII_TXD2_LSIO_GPIO6_IO14		0x00000021>;
+	};
+
+	/* Apalis CAN1 */
+	pinctrl_flexcan1: flexcan0grp {
+		fsl,pins = <IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX			0x00000021>,
+			   <IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX			0x00000021>;
+	};
+
+	/* Apalis CAN2 */
+	pinctrl_flexcan2: flexcan1grp {
+		fsl,pins = <IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX			0x00000021>,
+			   <IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX			0x00000021>;
+	};
+
+	/* Apalis CAN3 (optional) */
+	pinctrl_flexcan3: flexcan2grp {
+		fsl,pins = <IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX			0x00000021>,
+			   <IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX			0x00000021>;
+	};
+
+	/* Apalis GPIO1 */
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <IMX8QM_M40_GPIO0_00_LSIO_GPIO0_IO08			0x06000021>;
+	};
+
+	/* Apalis GPIO2 */
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins = <IMX8QM_M40_GPIO0_01_LSIO_GPIO0_IO09			0x06000021>;
+	};
+
+	/* Apalis GPIO3 */
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins = <IMX8QM_M41_GPIO0_00_LSIO_GPIO0_IO12			0x06000021>;
+	};
+
+	/* Apalis GPIO4 */
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <IMX8QM_M41_GPIO0_01_LSIO_GPIO0_IO13			0x06000021>;
+	};
+
+	/* Apalis GPIO5 */
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins = <IMX8QM_FLEXCAN2_RX_LSIO_GPIO4_IO01			0x06000021>;
+	};
+
+	/* Apalis GPIO6 */
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins = <IMX8QM_FLEXCAN2_TX_LSIO_GPIO4_IO02			0x00000021>;
+	};
+
+	/* Apalis GPIO7 */
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins = <IMX8QM_MLB_SIG_LSIO_GPIO3_IO26			0x00000021>;
+	};
+
+	/* Apalis GPIO8 */
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins = <IMX8QM_MLB_DATA_LSIO_GPIO3_IO28			0x00000021>;
+	};
+
+	/* Apalis BKL1_ON */
+	pinctrl_gpio_bkl_on: gpiobklongrp {
+		fsl,pins = <IMX8QM_LVDS0_GPIO00_LSIO_GPIO1_IO04			0x00000021>;
+	};
+
+	/* Apalis WAKE1_MICO */
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <IMX8QM_SPI3_CS0_LSIO_GPIO2_IO20			0x06700021>;
+	};
+
+	/* Apalis USBH_OC# */
+	pinctrl_gpio_usbh_oc_n: gpiousbhocngrp {
+		fsl,pins = <IMX8QM_USB_SS3_TC3_LSIO_GPIO4_IO06			0x04000021>;
+	};
+
+	/* On-module HDMI_CTRL */
+	pinctrl_hdmi_ctrl: hdmictrlgrp {
+		fsl,pins = <IMX8QM_MIPI_CSI1_GPIO0_00_LSIO_GPIO1_IO30		0x00000061>;
+	};
+
+	/* On-module I2C */
+	pinctrl_lpi2c1: lpi2c1grp {
+		fsl,pins = <IMX8QM_GPT0_CLK_DMA_I2C1_SCL			0x04000020>,
+			   <IMX8QM_GPT0_CAPTURE_DMA_I2C1_SDA			0x04000020>;
+	};
+
+	/* Apalis I2C1 */
+	pinctrl_lpi2c2: lpi2c2grp {
+		fsl,pins = <IMX8QM_GPT1_CLK_DMA_I2C2_SCL			0x04000020>,
+			   <IMX8QM_GPT1_CAPTURE_DMA_I2C2_SDA			0x04000020>;
+	};
+
+	/* Apalis I2C3 (CAM) */
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <IMX8QM_SIM0_PD_DMA_I2C3_SCL				0x04000020>,
+			   <IMX8QM_SIM0_POWER_EN_DMA_I2C3_SDA			0x04000020>;
+	};
+
+	/* Apalis SPI1 */
+	pinctrl_lpspi0: lpspi0grp {
+		fsl,pins = <IMX8QM_SPI0_SCK_DMA_SPI0_SCK			0x0600004c>,
+			   <IMX8QM_SPI0_SDO_DMA_SPI0_SDO			0x0600004c>,
+			   <IMX8QM_SPI0_SDI_DMA_SPI0_SDI			0x0600004c>,
+			   <IMX8QM_SPI0_CS0_LSIO_GPIO3_IO05			0x0600004c>;
+	};
+
+	/* Apalis SPI2 */
+	pinctrl_lpspi2: lpspi2grp {
+		fsl,pins = <IMX8QM_SPI2_SCK_DMA_SPI2_SCK			0x0600004c>,
+			   <IMX8QM_SPI2_SDO_DMA_SPI2_SDO			0x0600004c>,
+			   <IMX8QM_SPI2_SDI_DMA_SPI2_SDI			0x0600004c>,
+			   <IMX8QM_SPI2_CS0_LSIO_GPIO3_IO10			0x0600004c>;
+	};
+
+	/* Apalis UART3 */
+	pinctrl_lpuart0: lpuart0grp {
+		fsl,pins = <IMX8QM_UART0_RX_DMA_UART0_RX			0x06000020>,
+			   <IMX8QM_UART0_TX_DMA_UART0_TX			0x06000020>;
+	};
+
+	/* Apalis UART1 */
+	pinctrl_lpuart1: lpuart1grp {
+		fsl,pins = <IMX8QM_UART1_RX_DMA_UART1_RX			0x06000020>,
+			   <IMX8QM_UART1_TX_DMA_UART1_TX			0x06000020>,
+			   <IMX8QM_UART1_CTS_B_DMA_UART1_CTS_B			0x06000020>,
+			   <IMX8QM_UART1_RTS_B_DMA_UART1_RTS_B			0x06000020>;
+	};
+
+	/* Apalis UART1 */
+	pinctrl_lpuart1ctrl: lpuart1ctrlgrp {
+		fsl,pins = /* Apalis UART1_DTR */
+			   <IMX8QM_M40_I2C0_SCL_LSIO_GPIO0_IO06			0x00000021>,
+			   /* Apalis UART1_DSR */
+			   <IMX8QM_M40_I2C0_SDA_LSIO_GPIO0_IO07			0x00000021>,
+			   /* Apalis UART1_DCD */
+			   <IMX8QM_M41_I2C0_SCL_LSIO_GPIO0_IO10			0x00000021>,
+			   /* Apalis UART1_RI */
+			   <IMX8QM_M41_I2C0_SDA_LSIO_GPIO0_IO11			0x00000021>;
+	};
+
+	/* Apalis UART4 */
+	pinctrl_lpuart2: lpuart2grp {
+		fsl,pins = <IMX8QM_LVDS0_I2C1_SCL_DMA_UART2_TX			0x06000020>,
+			   <IMX8QM_LVDS0_I2C1_SDA_DMA_UART2_RX			0x06000020>;
+	};
+
+	/* Apalis UART2 */
+	pinctrl_lpuart3: lpuart3grp {
+		fsl,pins = <IMX8QM_LVDS1_I2C1_SCL_DMA_UART3_TX			0x06000020>,
+			   <IMX8QM_LVDS1_I2C1_SDA_DMA_UART3_RX			0x06000020>,
+			   <IMX8QM_ENET1_RGMII_TXD3_DMA_UART3_RTS_B		0x06000020>,
+			   <IMX8QM_ENET1_RGMII_RXC_DMA_UART3_CTS_B		0x06000020>;
+	};
+
+	/* Apalis TS_2 */
+	pinctrl_lvds0_i2c0_gpio: lvds0i2c0gpiogrp {
+		fsl,pins = <IMX8QM_LVDS0_I2C0_SCL_LSIO_GPIO1_IO06		0x00000021>;
+	};
+
+	/* Apalis LCD1_G6+7 */
+	pinctrl_lvds1_i2c0_gpios: lvds1i2c0gpiosgrp {
+		fsl,pins = /* Apalis LCD1_G6 */
+			   <IMX8QM_LVDS1_I2C0_SCL_LSIO_GPIO1_IO12		0x00000021>,
+			   /* Apalis LCD1_G7 */
+			   <IMX8QM_LVDS1_I2C0_SDA_LSIO_GPIO1_IO13		0x00000021>;
+	};
+
+	/* Apalis TS_3 */
+	pinctrl_mipi_dsi_0_1_en: mipidsi0-1engrp {
+		fsl,pins = <IMX8QM_LVDS0_I2C0_SDA_LSIO_GPIO1_IO07		0x00000021>;
+	};
+
+	/* Apalis TS_4 */
+	pinctrl_mipi_dsi1_gpios: mipidsi1gpiosgrp {
+		fsl,pins = <IMX8QM_MIPI_DSI1_GPIO0_00_LSIO_GPIO1_IO22		0x00000021>;
+	};
+
+	/* Apalis TS_1 */
+	pinctrl_mlb_gpios: mlbgpiosgrp {
+		fsl,pins = <IMX8QM_MLB_CLK_LSIO_GPIO3_IO27			0x00000021>;
+	};
+
+	/* Apalis MMC1_CD# */
+	pinctrl_mmc1_cd: mmc1cdgrp {
+		fsl,pins = <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09			0x00000021>;
+	};
+
+	pinctrl_mmc1_cd_sleep: mmc1cdsleepgrp {
+		fsl,pins = <IMX8QM_ESAI1_TX1_LSIO_GPIO2_IO09			0x04000021>;
+	};
+
+	/* On-module PCIe_Wi-Fi */
+	pinctrl_pcieb: pciebgrp {
+		fsl,pins = <IMX8QM_PCIE_CTRL1_CLKREQ_B_LSIO_GPIO4_IO30		0x00000021>,
+			   <IMX8QM_PCIE_CTRL1_WAKE_B_LSIO_GPIO4_IO31		0x00000021>,
+			   <IMX8QM_PCIE_CTRL1_PERST_B_LSIO_GPIO5_IO00		0x00000021>;
+	};
+
+	/* On-module PCIe_CLK_EN1 */
+	pinctrl_pcie_sata_refclk: pciesatarefclkgrp {
+		fsl,pins = <IMX8QM_USDHC2_WP_LSIO_GPIO4_IO11			0x00000021>;
+	};
+
+	/* On-module PCIe_CLK_EN2 */
+	pinctrl_pcie_wifi_refclk: pciewifirefclkgrp {
+		fsl,pins = <IMX8QM_ESAI1_TX3_RX2_LSIO_GPIO2_IO11		0x00000021>;
+	};
+
+	/* Apalis PWM3 */
+	pinctrl_pwm0: pwm0grp {
+		fsl,pins = <IMX8QM_UART0_RTS_B_LSIO_PWM0_OUT			0x00000020>;
+	};
+
+	/* Apalis PWM4 */
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <IMX8QM_UART0_CTS_B_LSIO_PWM1_OUT			0x00000020>;
+	};
+
+	/* Apalis PWM1 */
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <IMX8QM_GPT1_COMPARE_LSIO_PWM2_OUT			0x00000020>;
+	};
+
+	/* Apalis PWM2 */
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <IMX8QM_GPT0_COMPARE_LSIO_PWM3_OUT			0x00000020>;
+	};
+
+	/* Apalis BKL1_PWM */
+	pinctrl_pwm_bkl: pwmbklgrp {
+		fsl,pins = <IMX8QM_LVDS1_GPIO00_LVDS1_PWM0_OUT			0x00000020>;
+	};
+
+	/* Apalis LCD1_ */
+	pinctrl_qspi1a_gpios: qspi1agpiosgrp {
+		fsl,pins = /* Apalis LCD1_B0 */
+			   <IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26			0x00000021>,
+			   /* Apalis LCD1_B1 */
+			   <IMX8QM_QSPI1A_DATA1_LSIO_GPIO4_IO25			0x00000021>,
+			   /* Apalis LCD1_B2 */
+			   <IMX8QM_QSPI1A_DATA2_LSIO_GPIO4_IO24			0x00000021>,
+			   /* Apalis LCD1_B3 */
+			   <IMX8QM_QSPI1A_DATA3_LSIO_GPIO4_IO23			0x00000021>,
+			   /* Apalis LCD1_B5 */
+			   <IMX8QM_QSPI1A_DQS_LSIO_GPIO4_IO22			0x00000021>,
+			   /* Apalis LCD1_B7 */
+			   <IMX8QM_QSPI1A_SCLK_LSIO_GPIO4_IO21			0x00000021>,
+			   /* Apalis LCD1_B4 */
+			   <IMX8QM_QSPI1A_SS0_B_LSIO_GPIO4_IO19			0x00000021>,
+			   /* Apalis LCD1_B6 */
+			   <IMX8QM_QSPI1A_SS1_B_LSIO_GPIO4_IO20			0x00000021>;
+	};
+
+	/* On-module RESET_MOCI#_DRV */
+	pinctrl_reset_moci: resetmocigrp {
+		fsl,pins = <IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30			0x00000021>;
+	};
+
+	/* On-module I2S SGTL5000 for Apalis Analogue Audio */
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <IMX8QM_SAI1_TXD_AUD_SAI1_TXD			0xc600006c>,
+			   <IMX8QM_SAI1_RXD_AUD_SAI1_RXD			0xc600004c>,
+			   <IMX8QM_SAI1_TXC_AUD_SAI1_TXC			0xc600004c>,
+			   <IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS			0xc600004c>;
+	};
+
+	/* Apalis SATA1_ACT# */
+	pinctrl_sata1_act: sata1actgrp {
+		fsl,pins = <IMX8QM_ESAI1_TX0_LSIO_GPIO2_IO08			0x00000021>;
+	};
+
+	/* Apalis SD1_CD# */
+	pinctrl_sd1_cd: sd1cdgrp {
+		fsl,pins = <IMX8QM_USDHC2_CD_B_LSIO_GPIO4_IO12			0x00000021>;
+	};
+
+	/* On-module I2S SGTL5000 SYS_MCLK */
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0			0xc600004c>;
+	};
+
+	/* Apalis LCD1_ */
+	pinctrl_sim0_gpios: sim0gpiosgrp {
+		fsl,pins = /* Apalis LCD1_G5 */
+			   <IMX8QM_SIM0_CLK_LSIO_GPIO0_IO00			0x00000021>,
+			   /* Apalis LCD1_G3 */
+			   <IMX8QM_SIM0_GPIO0_00_LSIO_GPIO0_IO05		0x00000021>,
+			   /* Apalis TS_5 */
+			   <IMX8QM_SIM0_IO_LSIO_GPIO0_IO02			0x00000021>,
+			   /* Apalis LCD1_G4 */
+			   <IMX8QM_SIM0_RST_LSIO_GPIO0_IO01			0x00000021>;
+	};
+
+	/* Apalis SPDIF */
+	pinctrl_spdif0: spdif0grp {
+		fsl,pins = <IMX8QM_SPDIF0_TX_AUD_SPDIF0_TX			0xc6000040>,
+			   <IMX8QM_SPDIF0_RX_AUD_SPDIF0_RX			0xc6000040>;
+	};
+
+	pinctrl_touchctrl_gpios: touchctrlgpiosgrp {
+		fsl,pins = <IMX8QM_ESAI1_FSR_LSIO_GPIO2_IO04			0x00000021>,
+			   <IMX8QM_ESAI1_FST_LSIO_GPIO2_IO05			0x00000041>,
+			   <IMX8QM_SPI3_SCK_LSIO_GPIO2_IO17			0x00000021>,
+			   <IMX8QM_SPI3_CS1_LSIO_GPIO2_IO21			0x00000041>;
+	};
+
+	pinctrl_touchctrl_idle: touchctrlidlegrp {
+		fsl,pins = <IMX8QM_ADC_IN4_LSIO_GPIO3_IO22			0x00000021>,
+			   <IMX8QM_ADC_IN5_LSIO_GPIO3_IO23			0x00000021>,
+			   <IMX8QM_ADC_IN6_LSIO_GPIO3_IO24			0x00000021>,
+			   <IMX8QM_ADC_IN7_LSIO_GPIO3_IO25			0x00000021>;
+	};
+
+	/* On-module USB HSIC HUB (active) */
+	pinctrl_usb_hsic_active: usbh1activegrp {
+		fsl,pins = <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA		0x000000cf>,
+			   <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE	0x000000ff>;
+	};
+
+	/* On-module USB HSIC HUB (idle) */
+	pinctrl_usb_hsic_idle: usbh1idlegrp {
+		fsl,pins = <IMX8QM_USB_HSIC0_DATA_CONN_USB_HSIC0_DATA		0x000000cf>,
+			   <IMX8QM_USB_HSIC0_STROBE_CONN_USB_HSIC0_STROBE	0x000000cf>;
+	};
+
+	/* On-module USB HSIC HUB */
+	pinctrl_usb3503a: usb3503agrp {
+		fsl,pins = /* On-module HSIC_HUB_CONNECT */
+			   <IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31			0x00000041>,
+			   /* On-module HSIC_INT_N */
+			   <IMX8QM_SCU_GPIO0_05_LSIO_GPIO1_IO01			0x00000021>,
+			   /* On-module HSIC_RESET_N */
+			   <IMX8QM_SCU_GPIO0_06_LSIO_GPIO1_IO02			0x00000041>;
+	};
+
+	/* Apalis USBH_EN */
+	pinctrl_usbh_en: usbhengrp {
+		fsl,pins = <IMX8QM_USB_SS3_TC1_LSIO_GPIO4_IO04			0x00000021>;
+	};
+
+	/* Apalis USBO1 */
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = /* Apalis USBO1_EN */
+			   <IMX8QM_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021>,
+			   /* Apalis USBO1_OC# */
+			   <IMX8QM_USB_SS3_TC2_CONN_USB_OTG1_OC			0x04000021>;
+	};
+
+	/* On-module eMMC */
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000041>,
+			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000021>,
+			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000021>,
+			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000021>,
+			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000021>,
+			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000021>,
+			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000021>,
+			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000021>,
+			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000021>,
+			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000021>,
+			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000041>,
+			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000021>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000040>,
+			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000020>,
+			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020>,
+			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020>,
+			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020>,
+			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020>,
+			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020>,
+			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020>,
+			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020>,
+			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020>,
+			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000040>,
+			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000020>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK			0x06000040>,
+			   <IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD			0x00000020>,
+			   <IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020>,
+			   <IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020>,
+			   <IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020>,
+			   <IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020>,
+			   <IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020>,
+			   <IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020>,
+			   <IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020>,
+			   <IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020>,
+			   <IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE		0x06000040>,
+			   <IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B		0x00000020>;
+	};
+
+	/* Apalis TS_6 */
+	pinctrl_usdhc1_gpios: usdhc1gpiosgrp {
+		fsl,pins = <IMX8QM_USDHC1_STROBE_LSIO_GPIO5_IO23		0x00000021>;
+	};
+
+	/* Apalis MMC1 */
+	pinctrl_usdhc2_4bit: usdhc2grp4bitgrp {
+		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000041>,
+			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000021>,
+			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000021>,
+			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000021>,
+			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000021>,
+			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000021>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc2_4bit_100mhz: usdhc2-4bit100mhzgrp {
+		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040>,
+			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020>,
+			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000020>,
+			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000020>,
+			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000020>,
+			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000020>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc2_4bit_200mhz: usdhc2-4bit200mhzgrp {
+		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040>,
+			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020>,
+			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x00000020>,
+			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x00000020>,
+			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x00000020>,
+			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x00000020>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc2_8bit: usdhc2grp8bitgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000021>,
+			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000021>,
+			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000021>,
+			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000021>;
+	};
+
+	pinctrl_usdhc2_8bit_100mhz: usdhc2-8bit100mhzgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000020>,
+			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000020>,
+			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000020>,
+			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000020>;
+	};
+
+	pinctrl_usdhc2_8bit_200mhz: usdhc2-8bit200mhzgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x00000020>,
+			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x00000020>,
+			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x00000020>,
+			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x00000020>;
+	};
+
+	pinctrl_usdhc2_4bit_sleep: usdhc2-4bitsleepgrp {
+		fsl,pins = <IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x04000061>,
+			   <IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x04000061>,
+			   <IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0		0x04000061>,
+			   <IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1		0x04000061>,
+			   <IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2		0x04000061>,
+			   <IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3		0x04000061>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc2_8bit_sleep: usdhc2-8bitsleepgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA4_CONN_USDHC1_DATA4		0x04000061>,
+			   <IMX8QM_USDHC1_DATA5_CONN_USDHC1_DATA5		0x04000061>,
+			   <IMX8QM_USDHC1_DATA6_CONN_USDHC1_DATA6		0x04000061>,
+			   <IMX8QM_USDHC1_DATA7_CONN_USDHC1_DATA7		0x04000061>;
+	};
+
+	/* Apalis SD1 */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
+			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
+			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
+			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
+			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
+			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
+			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
+			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
+			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
+			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
+			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041>,
+			   <IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021>,
+			   <IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0		0x00000021>,
+			   <IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1		0x00000021>,
+			   <IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2		0x00000021>,
+			   <IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3		0x00000021>,
+			   /* On-module PMIC use */
+			   <IMX8QM_USDHC2_VSELECT_CONN_USDHC2_VSELECT		0x00000021>;
+	};
+
+	/* On-module Wi-Fi */
+	pinctrl_wifi: wifigrp {
+		fsl,pins = /* On-module Wi-Fi_SUSCLK_32k */
+			   <IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K	0x06000021>,
+			   /* On-module Wi-Fi_PCIE_W_DISABLE */
+			   <IMX8QM_MIPI_CSI0_MCLK_OUT_LSIO_GPIO1_IO24		0x06000021>;
+	};
+
+	pinctrl_wifi_pdn: wifipdngrp {
+		fsl,pins = /* On-module Wi-Fi_POWER_DOWN */
+			   <IMX8QM_MIPI_CSI0_GPIO0_01_LSIO_GPIO1_IO28		0x06000021>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
new file mode 100644
index 000000000000..81ba8b2831ac
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1.dtsi
@@ -0,0 +1,16 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8qm.dtsi"
+#include "imx8-apalis-v1.1.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX8QM V1.1";
+	compatible = "toradex,apalis-imx8-v1.1",
+		     "fsl,imx8qm";
+};
+
+/* TODO: Cooling Maps */
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi
new file mode 100644
index 000000000000..1c6af9f549a8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis.dtsi
@@ -0,0 +1,340 @@ 
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8qm-apalis-v1.1.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX8QM";
+	compatible = "toradex,apalis-imx8",
+		     "fsl,imx8qm";
+};
+
+&ethphy0 {
+	interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+};
+
+/*
+ * Apalis iMX8QM V1.0 has PHY KSZ9031. the Micrel PHY driver
+ * doesn't support setting internal PHY delay for TXC line for
+ * this PHY model. Use delay on MAC side instead.
+ */
+&fec1 {
+	fsl,rgmii_txc_dly;
+	phy-mode = "rgmii-rxid";
+};
+
+/* TODO: Apalis HDMI1 */
+
+/* Apalis I2C2 (DDC) */
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c0>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+};
+
+&lsio_gpio0 {
+	gpio-line-names = "MXM3_279",
+			  "MXM3_277",
+			  "MXM3_135",
+			  "MXM3_203",
+			  "MXM3_201",
+			  "MXM3_275",
+			  "MXM3_110",
+			  "MXM3_120",
+			  "MXM3_1/GPIO1",
+			  "MXM3_3/GPIO2",
+			  "MXM3_124",
+			  "MXM3_122",
+			  "MXM3_5/GPIO3",
+			  "MXM3_7/GPIO4",
+			  "",
+			  "",
+			  "MXM3_4",
+			  "MXM3_211",
+			  "MXM3_209",
+			  "MXM3_2",
+			  "MXM3_136",
+			  "MXM3_134",
+			  "MXM3_6",
+			  "MXM3_8",
+			  "MXM3_112",
+			  "MXM3_118",
+			  "MXM3_114",
+			  "MXM3_116";
+};
+
+&lsio_gpio1 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_286",
+			  "",
+			  "MXM3_87",
+			  "MXM3_99",
+			  "MXM3_138",
+			  "MXM3_140",
+			  "MXM3_239",
+			  "",
+			  "MXM3_281",
+			  "MXM3_283",
+			  "MXM3_126",
+			  "MXM3_132",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_173",
+			  "MXM3_175",
+			  "MXM3_123";
+};
+
+&lsio_gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_198",
+			  "MXM3_35",
+			  "MXM3_164",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_217",
+			  "MXM3_215",
+			  "",
+			  "",
+			  "MXM3_193",
+			  "MXM3_194",
+			  "MXM3_37",
+			  "",
+			  "MXM3_271",
+			  "MXM3_273",
+			  "MXM3_195",
+			  "MXM3_197",
+			  "MXM3_177",
+			  "MXM3_179",
+			  "MXM3_181",
+			  "MXM3_183",
+			  "MXM3_185",
+			  "MXM3_187";
+};
+
+&lsio_gpio3 {
+	gpio-line-names = "MXM3_191",
+			  "",
+			  "MXM3_221",
+			  "MXM3_225",
+			  "MXM3_223",
+			  "MXM3_227",
+			  "MXM3_200",
+			  "MXM3_235",
+			  "MXM3_231",
+			  "MXM3_229",
+			  "MXM3_233",
+			  "MXM3_204",
+			  "MXM3_196",
+			  "",
+			  "MXM3_202",
+			  "",
+			  "",
+			  "",
+			  "MXM3_305",
+			  "MXM3_307",
+			  "MXM3_309",
+			  "MXM3_311",
+			  "MXM3_315",
+			  "MXM3_317",
+			  "MXM3_319",
+			  "MXM3_321",
+			  "MXM3_15/GPIO7",
+			  "MXM3_63",
+			  "MXM3_17/GPIO8",
+			  "MXM3_12",
+			  "MXM3_14",
+			  "MXM3_16";
+};
+
+&lsio_gpio4 {
+	gpio-line-names = "MXM3_18",
+			  "MXM3_11/GPIO5",
+			  "MXM3_13/GPIO6",
+			  "MXM3_274",
+			  "MXM3_84",
+			  "MXM3_262",
+			  "MXM3_96",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_190",
+			  "",
+			  "",
+			  "",
+			  "MXM3_269",
+			  "MXM3_251",
+			  "MXM3_253",
+			  "MXM3_295",
+			  "MXM3_299",
+			  "MXM3_301",
+			  "MXM3_297",
+			  "MXM3_293",
+			  "MXM3_291",
+			  "MXM3_289",
+			  "MXM3_287";
+
+	/* Enable pcie root / sata ref clock unconditionally */
+	pcie-sata-hog {
+		gpios = <27 GPIO_ACTIVE_HIGH>;
+	};
+
+};
+
+&lsio_gpio5 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_150",
+			  "MXM3_160",
+			  "MXM3_162",
+			  "MXM3_144",
+			  "MXM3_146",
+			  "MXM3_148",
+			  "MXM3_152",
+			  "MXM3_156",
+			  "MXM3_158",
+			  "MXM3_159",
+			  "MXM3_184",
+			  "MXM3_180",
+			  "MXM3_186",
+			  "MXM3_188",
+			  "MXM3_176",
+			  "MXM3_178";
+};
+
+&lsio_gpio6 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_261",
+			  "MXM3_263",
+			  "MXM3_259",
+			  "MXM3_257",
+			  "MXM3_255",
+			  "MXM3_128",
+			  "MXM3_130",
+			  "MXM3_265",
+			  "MXM3_249",
+			  "MXM3_247",
+			  "MXM3_245",
+			  "MXM3_243";
+};
+
+&pinctrl_fec1 {
+	fsl,pins =
+		/* Use pads in 1.8V mode */
+		<IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
+		<IMX8QM_ENET0_MDC_CONN_ENET0_MDC				0x06000020>,
+		<IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO				0x06000020>,
+		<IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL		0x06000020>,
+		<IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC			0x06000020>,
+		<IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0			0x06000020>,
+		<IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1			0x06000020>,
+		<IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2			0x06000020>,
+		<IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3			0x06000020>,
+		<IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC			0x06000020>,
+		<IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL		0x06000020>,
+		<IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0			0x06000020>,
+		<IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1			0x06000020>,
+		<IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2			0x06000020>,
+		<IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3			0x06000020>,
+		<IMX8QM_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M	0x06000020>,
+		/* On-module ETH_RESET# */
+		<IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x06000020>,
+		/* On-module ETH_INT# */
+		<IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05				0x04000060>;
+};
+
+&pinctrl_fec1_sleep {
+	fsl,pins =
+		<IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD			0x000014a0>,
+		<IMX8QM_ENET0_MDC_LSIO_GPIO4_IO14				0x04000040>,
+		<IMX8QM_ENET0_MDIO_LSIO_GPIO4_IO13				0x04000040>,
+		<IMX8QM_ENET0_RGMII_TX_CTL_LSIO_GPIO5_IO31			0x04000040>,
+		<IMX8QM_ENET0_RGMII_TXC_LSIO_GPIO5_IO30				0x04000040>,
+		<IMX8QM_ENET0_RGMII_TXD0_LSIO_GPIO6_IO00			0x04000040>,
+		<IMX8QM_ENET0_RGMII_TXD1_LSIO_GPIO6_IO01			0x04000040>,
+		<IMX8QM_ENET0_RGMII_TXD2_LSIO_GPIO6_IO02			0x04000040>,
+		<IMX8QM_ENET0_RGMII_TXD3_LSIO_GPIO6_IO03			0x04000040>,
+		<IMX8QM_ENET0_RGMII_RXC_LSIO_GPIO6_IO04				0x04000040>,
+		<IMX8QM_ENET0_RGMII_RX_CTL_LSIO_GPIO6_IO05			0x04000040>,
+		<IMX8QM_ENET0_RGMII_RXD0_LSIO_GPIO6_IO06			0x04000040>,
+		<IMX8QM_ENET0_RGMII_RXD1_LSIO_GPIO6_IO07			0x04000040>,
+		<IMX8QM_ENET0_RGMII_RXD2_LSIO_GPIO6_IO08			0x04000040>,
+		<IMX8QM_ENET0_RGMII_RXD3_LSIO_GPIO6_IO09			0x04000040>,
+		<IMX8QM_ENET0_REFCLK_125M_25M_LSIO_GPIO4_IO15			0x04000040>,
+		<IMX8QM_LVDS1_GPIO01_LSIO_GPIO1_IO11				0x04000040>,
+		<IMX8QM_LVDS0_GPIO01_LSIO_GPIO1_IO05				0x04000040>;
+};
+
+&iomuxc {
+	/* Apalis I2C2 (DDC) */
+	pinctrl_lpi2c0: lpi2c0grp {
+		fsl,pins =
+			<IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL			0x04000022>,
+			<IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA			0x04000022>;
+	};
+};
+
+/* On-module PCIe_CTRL0_CLKREQ */
+&pinctrl_pcie_sata_refclk {
+	fsl,pins =
+		<IMX8QM_PCIE_CTRL0_CLKREQ_B_LSIO_GPIO4_IO27			0x00000021>;
+};
+
+/* TODO: On-module Wi-Fi */
+
+/* Apalis MMC1 */
+&usdhc2 {
+	/*
+	 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
+	 * issues with certain SD cards, disable 1.8V signaling for now.
+	 */
+	no-1-8-v;
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	/*
+	 * The PMIC on V1.0A HW generates 1.6V instead of 1.8V which creates
+	 * issues with certain SD cards, disable 1.8V signaling for now.
+	 */
+	no-1-8-v;
+};