diff mbox series

[6/9] ARM: dts: imx28-duckbill-2: Include base board

Message ID 20230201203338.9525-7-stefan.wahren@i2se.com (mailing list archive)
State New, archived
Headers show
Series ARM: dts: imx28: Clean up older DTS files | expand

Commit Message

Stefan Wahren Feb. 1, 2023, 8:33 p.m. UTC 
All additional I2SE Duckbill 2 variants always have the same
base board in common. So consider this by including the base
board and avoid a lot of redundancy.

Special care needs to be taken of the SPI variant. ssp2 is used
as SD card interface on the base board, but on the SPI variant
it's downgrade to a SPI interface to connect the QCA7000. So
the SD card properties must be deleted.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Michael Heimpold <mhei@heimpold.de>
---
 arch/arm/boot/dts/imx28-duckbill-2-485.dts    | 174 ++-------------
 .../arm/boot/dts/imx28-duckbill-2-enocean.dts | 198 +++-------------
 arch/arm/boot/dts/imx28-duckbill-2-spi.dts    | 211 ++++--------------
 3 files changed, 81 insertions(+), 502 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
index d451fa018d83..b73020ff1053 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
@@ -5,172 +5,13 @@ 
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 485";
 	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
 		rs485-red {
 			label = "duckbill:red:rs485";
 			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -182,3 +23,16 @@  rs485-green {
 		};
 	};
 };
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
index 73f521c46c1e..473d99b9b42f 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -5,184 +5,14 @@ 
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 EnOcean";
 	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_AUART0_CTS__GPIO_3_2
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				enocean_button: enocean-button@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
 		enocean-blue {
 			label = "duckbill:blue:enocean";
 			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
@@ -211,3 +41,29 @@  key-enocean {
 		};
 	};
 };
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_AUART0_CTS__GPIO_3_2
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
+
+&pinctrl {
+	enocean_button: enocean-button@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
index 0e8be5975709..859d97a5a775 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
@@ -5,9 +5,7 @@ 
  */
 
 /dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
+#include "imx28-duckbill-2.dts"
 
 / {
 	model = "I2SE Duckbill 2 SPI";
@@ -16,179 +14,50 @@  / {
 	aliases {
 		ethernet1 = &qca7000;
 	};
+};
 
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				qca7000: ethernet@0 {
-					reg = <0>;
-					compatible = "qca,qca7000";
-					pinctrl-names = "default";
-					pinctrl-0 = <&qca7000_pins>;
-					interrupt-parent = <&gpio3>;
-					interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-					spi-cpha;
-					spi-cpol;
-					spi-max-frequency = <8000000>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: led@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				qca7000_pins: qca7000@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
-						MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
-						MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
-						MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
-						MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
-						MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
+&auart0 {
+	status = "disabled";
+};
 
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
+&i2c0 {
+	status = "disabled";
+};
 
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
+&pinctrl {
+	qca7000_pins: qca7000@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
+			MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
+			MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
+			MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
+			MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
+			MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
 	};
+};
 
-	leds {
-		compatible = "gpio-leds";
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	/delete-property/ bus-width;
+	/delete-property/ vmmc-supply;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		reg = <0>;
+		compatible = "qca,qca7000";
 		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
+		pinctrl-0 = <&qca7000_pins>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <8000000>;
 	};
 };