diff mbox series

[v12,5/8] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support

Message ID 20230301091136.17862-6-r-gunasekaran@ti.com (mailing list archive)
State New, archived
Headers show
Series arm64: j721s2: Add support for additional IPs | expand

Commit Message

Ravi Gunasekaran March 1, 2023, 9:11 a.m. UTC 
From: Aswath Govindraju <a-govindraju@ti.com>

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that up to 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
---
I had reviewed this patch in the v5 series [0].
Since I'm taking over upstreaming this series, I removed the self
Reviewed-by tag.

[0] - https://lore.kernel.org/all/96058a13-4903-2b8c-8de2-f37fdfd3672b@ti.com/

Changes from v11:
* No change

Changes from v10:
* Removed Link tag from commit message

Changes from v9:
* Enabled USB nodes

Changes from v8:
* No change

Changes from v7:
* No change

Changes from v6:
* No change

Changes from v5:
* Removed Cc tags from commit message

Changes from v4:
* No change

Changes from v3:
* No change

Changes from v2:
* No change

Changes from v1:
* No change

 .../dts/ti/k3-j721s2-common-proc-board.dts    | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 907f34ff22a5..fa38940fe6cd 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ 
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -323,6 +329,24 @@ 
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	status = "okay";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";